How To: Install Fuel Injectors & Link DAT File to EMM || Evinrude Etec

The Dylan Be Fishing Channel
Quick & Easy Fix
How To: remove and install new fuel injector on a 2006 Evinrude etec 225 and link new injector DAT file to EMM. VERYYY IMPORTANT when installing new injector.
Tip: on how to make a starboard side injector into a port side injector
I"m not a certified Evinrude mechanic.
the injector that was removed was #2
Hope this video was helpful!
Like & Subscribe
Amazon Link for Evinrude Software:
www.amazon.com...

[@blaineavalle6211]

Awesome video brother. All the forums try scaring everyone into taking it into the dealership to upload coefficient and if you don't you will definitely blow your engine up. Cut and dry and so much simpler that I thought. Thank you!

[@dylanbefishing]

thanks! yea i was that guy who paid with my first injector issue and figured out the secrets lol going to make a video on testing the injectors next

[@redefinefishing3079]

Thank you so much, this is the best video we have seen, we paid over $2k on replacing two injectors on our etec 150, for sure we are doing the work ourself next time.

[@Hectorgutierrez]

Thank you so much! I have a 2006 Evinrude Etec 90 . #1 cylinder wasn’t making power. This was verified by pulling the spark plug boot and seeing no RPM change. I did have spark and 121 psi compression on all cylinders. I tested the resistance of the fuel injector and it was only 1.7 ohms. Should be 2-3 ohms. So I bought the diagnostic software you used, new fuel injector and had the fuel injector dat file emailed to me. Installed everything and bam! Engine is running perfect again! Thanks a million! Couldn’t of done without watching your video!

[@bankney49]

Could you please do a video on replacing an EMM ? I would like to know if it can be done without involving a dealer. Thanks!

[@cburrell66]

I would love to see this to

[@c219troll]

Great video. I learned the hard way to check if your motor has been repowered. Order the wrong fuel injector.

[@dylanbefishing]

oh man yea its a weird injector system for sure

[@carlosMako]

Great videos brother, keep them coming-very helpful info! nice Mako 231/Etec, I have almost the same setup lol, got a 88 231 with a 05 Etec 225, just found out my EMM is bad keeps faulting a #18 code reading 55 volt circuit above range, have you ever dealt with this issue, or do you know of anyone in the Miami/FL area that might repair these emms or sell used ones-im stuck on this one-appreciate the content-I'm a fan!

[@MrBigezee69]

Thank you for the video. Where did you get the cable to connect your computer to the engine? I have the same amazon repair program but it did not come with a cable

[@claytonpinheiro7635]

Nice ! From Amazônia Brazil !

[@mathewlacroix7630]

Hello Dylan Thanks for the video. I have done everything you did in the video. The #2 LED on my EMM is still lit and the engine will not stay running (it runs and then shuts off) any idea how to get the EMM LED to reset?

[@juanrosado6402]

Hi great video. Can you do a video doing more troubleshooting with the software. Like taking codes from the ecm it would be helpful. I ordered a set of cables to troubleshoot my engine over heating problem from Amazon .

[@dylanbefishing]

yes i can do that for you soon, if you need any help just reach out and ill do my best!👍🏼

[@sheldonesteb]

Man, this is so helpful! Thanks for putting it together

[@jebmcdonald5709]

If buy a used injector and don’t get a coeffiencent file can I just scan the code on black tag to get the coefficient

[@dylanbefishing]

Yes

[@francescodipietro347]

@jebmcdonald5700 & @dylanbefishing but once scanned the black tag, where do you download from??? Thx!

[@daddski1]

@@francescodipietro347 email that scan to your email, run the software and when the scan dialog box pops up, copy your file and paste into the two dialog boxes just as if you used a scanner.

[@Jupiterhomegroup]

Thank you for making the video. Very informative!!!

[@dylanbefishing]

no problem!🤙🏼

[@francescodipietro347]

Best video! Congratulation! If i buy the used iniector but once scanned the black tag, where do you download from??? Thx!

[@innovativepowersports]

Wish I seen this before spending $900 at Barnicle Bills and them still not sending me the .dat file that I am still waiting for. The software from them is $345. Looks like the same software on Amazon like you got is only $60.

[@ericbuckley4971]

Hey Dylan, my engine is a 300 etech February 2006 , the injectors only have 2 wipers and your saying 3 wires ,there is no orange wire , I have twin 300 ‘s same dates , one has injectors with the orange wire , which is now a spare engine, and the one I have one my boat has 2 wires on the injectors, no orange wire , I was going to swap out a couple of injectors,as the 4 and 5 injectors have stopped working and I can’t get replacement, for the 2 wires, I see that the housing are interchangeable but the injectors are not , do you have any ideas , as you seem to be more knowledgeable that our local dealer. Thank you Eric Buckley

[@daddski1]

the orange wire is for the coil.

[@user-lj3vv6qj3r]

Hey. great video. Learned a lot from it. I’m trying to get injectors done now on my 2007 175’s. They’re telling me they need a check sum number as well as the serial number? Any truth to that? What does the cs number do that the sn couldn’t? Also where did you find the injectors? Lol completely agreed that they’re hard to find.

[@joshuaj614]

Am i able to just scan the qr on an injector to get the number to use on say a used emm swap?

[@daddski1]

yes, then email it to yourself. After that, when the software asks you if you want to or have a scanner tell it yes. it will open a dialog box and you just copy and paste in the scanner boxes. The system will think you used a scanner and there ya go. all done after clicking the right boxes yes.

[@ayhankucukozer1478]

Hello.. The line coming to one injector of the 30 hp etech engine is not working. ecu is solid. There is a problem with the electrical installation. I wonder which cables should I look at? Can you please help? Yanıtla

[@anthonytorres1741]

Hi Question I have a evinrude E tech 2007 115 what year till what year I can use injectors from

[@brianjohnson1647]

there is zero info on how to take the dat file from email to install on laptop. tried many times. it doesn't down load

[@daddski1]

the software will have a popup dialog box asking you if you want to use a scanner to get that code. say yes, copy and paste the number thread from the email into that dialog box (two times, one below the other in the second box) and then follow instructions. The system will assume you scanned these numbers in.

[@davepoidy5520]

thankyou from orillia Ontario canada

[@kirkgemmell5833]

Hi bud we busy with this same thing but we also have had to source a second hand EMM - do we have to do this for all existing injectors not replaced ? Furthermore not sure where to get DAT files for existing injectors - help appreciated TIA kirk

[@primate2744]

I have this exact motor on a boat I just bought. People fear monger on e-tec. I have a 2019 60 on my skiff that has been great. Has this motor been good for you?

[@dylanbefishing]

i love it... never let me down as long as you listen to the engine because the injectors... 5 out 6 have been replaced and they're not cheap but other than that i cant complain 23ft mako goes 45mph on a flat day and pretty good on fuel

[@240Turbo48]

Beauty, perfect. Thanks!

[@jimknopke8037]

Nice vid. Thanks

[@dylanbefishing]

🤙🏼🤙🏼🤙🏼

[@alecborge5404]

Hi I had a fuel injector fail also a fried emm that’s unreadable. I was able to get a new set however have no experience with the programming side. Do you have any experience installing/programming a new emm? Also can it be done with the Amazon program software?

[@mortendalendalen1531]

But if you purchase a uset ones . Where do you get the file the dealership send you ???? Best regards Morten ..

[@daddski1]

scan the qr code on the injector you bought, email that file to yourself, when the software asks you if you have a scanner. say yes. copy and paste THE ENTIRE THREAD of numbers you emailed to yourself into the two dialog boxes and follow the instructions.

[@mariomorales8002]

One question can u sent me the link where u bought ur injector because last year I tryied replacing my injector seen a few video yet I couldn’t scan the tag to update the computer but if I can buy the injector on the website hopefully I can get the email and fallow ur instruction

[@johanbergqvist5357]

Is it hard to get parts to E-TEC engines?

[@PappyLearnFishing]

2012 Etec 250 H.O. can elect injector be cleaned?

[@daddski1]

sure. and there are several guys that you can send them to who will clean, replace the screens and test for about 35 dollars or less per injector. Very reliable and worth the time to ship ... just look u on google "who in my area does etec injectors"

[@fishingwithslayer9458]

I have a 15hp etec will the software work

[@alecborge5404]

Hi I had a fuel injector fail also a fried emm that’s unreadable. I was able to get a new set however have no experience with the programming side. Do you have any experience installing/programming a new emm? Also can it be done with the Amazon program software?

[@rogerhutchins69]

Nice video . I would like to hire you to help me with my 30hp