How to Install Low Mount Fender Eliminator on 2019+ Kawasaki ZX-6R by TST Industries

[@slball123]

You are very good at narrating what you are doing and giving clear instructions. Well spoken dude

[@t3keen0ob]

Do you have an eta on when the low mount will be back in stock? I would rather wait to buy this than the standard mount. I subscribed on your website for notifications, thanks

[@TSTindustries]

The laser cutting should be done this week. Then they go to powdercoat. After that assembly. I would say that if you can be patient for a week or two you will get your preferred choice -BR

[@t3keen0ob]

@@TSTindustries nice, thanks for the update!!!

[@savageboy5533]

So I got the hyper pack for 2024 zx6r. Everything is going well but I’m pretty confused on the wiring for the license plate light.

[@jeffomspaugh6691]

It's easier to put the plate on the bracket first.

[@chazvelarde1055]

I did it pretty easy, I haven’t installed the taillight yet which I bought. But I have a check engine light on. I havent pulled codes but I do have two plug ins not connected due to the old plate. Any idea on how to fix?

[@masonwooster7336]

What did you do with the exhaust servo? Do you have a servo buddy or are you just rocking the engine light

[@masonwooster7336]

Scratch that I hear you say servo buddy I just had to listen a little longer

[@robertcallahan760]

So clean!

[@rzrpwr]

Im wondering if the block off plate can be ordered with black screws

[@TSTindustries]

Due to the lack of practicality of black hardware we do not supply pur kits with that option. We use stainless steel hardware .

[@elricaguilar6693]

Is this mount compatible with turn signals like the R7 low mount ?

[@TSTindustries]

Yes, you can mount a similar setup on this bracket. -BR

[@Jade___]

I have your fender eliminator and integrated tail light on my ninja 400, could i take those out and put them on a 24 zx6r?

[@TSTindustries]

The tail light, yes, but not the fender eliminator. -TST

[@Jade___]

@@TSTindustries Thanks for the quick reply!

[@TSTindustries]

@@Jade___ No problem!

[@jeffomspaugh6691]

This video didn't show how the low plate bracket mounted to the bike

[@TSTindustries]

Sure it does. Check out the 6:30 timestamp.

[@jeffomspaugh6691]

I don't know how I missed that​@@TSTindustries

[@TSTindustries]

@@jeffomspaugh6691 Lol no worries!

[@codyjenkins6570]

Will the 19+ version work on a 2016?

[@TSTindustries]

Unfortunately no. We do however offer a 2013-2018 specific tail light that you can find at our website TSTindustries.com . That part also has an instructional video to help you with installation.

[@cuzimaluzer777]

Any plans on doing some rear footpeg blanking plates?

[@TSTindustries]

Nah. We have done those in the past and they rarely sell. It was a waste of effort and time

[@zz-ic6dx]

What did you end up using to hide the holes where rear footpegs went?

[@TSTindustries]

@@zz-ic6dx the rear pegs are still on this bike. We did not remove those

[@ernestoantonio3496]

Does this fits on a 2014 zx6r?

[@TSTindustries]

It only fits 19 and up

[@zz-ic6dx]

On the part when you take those 2 screws out and subframe droops, i cannot get them both to align no matter how much i push up on subframe, i got one bolt in but no luck on other one. I had the entire tail taken apart cause i was doing taillight and fender together, do i need to reassemble tail first?

[@TSTindustries]

The subframe should be in place, and the subtray shifts within it. You just have to move around the subtray as you try to penetrate with the screw. Once concentric alignment is accomplished between subframe, subtray, and screw, it all just pops together.

[@aliankusmadi]

Nice

[@Lopez23300]

Will this fit a zx10r?😮‍💨

[@TSTindustries]

No but we have a dedicated low mount fender eliminator for the 10

[@Lopez23300]

@@TSTindustries shoot darn. I seen that. Was just hoping could get one placed like this🤘🏽

[@Yams6R]

I see that the Low Fender Mount is out of stock as of 4/17, when will it be back in stock?

[@TSTindustries]

We’re hoping to restock within the next month or so pending no further delays.

[@corcortou]

รันจากต้น