How to install PVC Bathroom Wall Panels

[@CoolDude-tz5co]

Excellent video, gets straight to the point with no nonsense, thanks

[@CiceronSpunky]

I always look forward to your videos.

[@czeital]

Good start but nothing on how to get that width cut correct if you need whole panel to corner - ie: if things are out of square etc and also are panel widths stated in/ex tongue and how are trips accomodated in width calcualtion. Also saw nothing on how to deal with the bottom when it's meeting a bath which would be great to know thanks

[@Chollanger148-pv8jp]

never even begin in that case :)

[@nairagasparetto]

It could be installed on a existing tile wall?

[@terrybenedict1]

VERY DRAMATIC

[@ebayseller6040]

can I make a table using this??

[@evashell]

Can you stick on top of old tile.As i will be using it as a kitchen splash back.

[@vcsradio2805]

Good job. Can this board be applied to a cement wall

[@gregc7699]

Yes

[@MidnightMoonlight92]

Can I put wall panels over Artex?

[@shaidanasreen134]

What about around the bathroom window or is this just suitable for straight wall, if you can pleas make video

[@thespecialist7]

Hi should you prime the wall first ,I am using plasterboard. Using Silicone to stick the wall panels. Or can I just plasterboard the wall first?

[@NarrowboatSuperB]

If you have plasterboard that has not been skimmed, just use PVA, mix pva with water, brush it onto the board.

[@kadrdil]

Thanks for your video what's the best silicone for stick the wall panel???

[@alistermcnicoll2634]

If putting on top of existing tiles is there not a problem of getting pipe connections of controls etc through the extra thickness?

[@NarrowboatSuperB]

Most of these boards are 5mm

[@flexhex3334]

what panel is this, im looking for it on your website and cant find it. Many thanks

[@RichardCropper]

Can this be applied over wall paper?

[@Xan-zh5ni]

Hi how would I replace a damaged panel?

[@samuelhara4874]

How do you fit the last panels

[@asmarahi3311]

Can we do colour on pvc panneling

[@dobarjepostenje662]

Can you put this wall panels on any type of wall? If I start doing this on which things I should be careful about

[@aimansaleem6166]

What is the material of these pvc?

[@silverbackag9790]

PVC.

[@cokhitonghop9256]

Well done

[@brrymcgolly]

Oh yes it looks very easy but they don't tell you about the awkward cuts when you get to the end. You can't guarantee not all bathrooms a square.. but a very good video

[@ealingbroadway2000]

That’s why you measure, we had height differences that went into a slant from corner to corner, that was a real pain

[@Immortaljme]

Can you use these panels on top of existing wall tiles?

[@twobins2060]

Yes

[@thelargest7614]

Of course, that would be even better probably.

[@markbellars6961]

If you fit over existing tiles surely the end trim will sit off the wall by the depth of the old tile and look weird.

[@pvclover76]

Do I need to put a bead of silicon in each side of the corner trim before pushing the panels in ?

[@svkscorpio]

Doesn't water seep in between the panels and cause the wall to dampen and also growth of mold behind them?

[@chrisbelfast6662]

No because you will use trims for the ends on the panels so it's water tight

[@alanoliver5378]

As instructed in the video, apply silicone sealer to the TnG joint of each panel.

[@privatechannel8462]

​@@Parkertannerzi did this, then found out it was me

[@ealingbroadway2000]

PVC cladding panels come in different sizes, mine were 8’x4’ and easier to work with, only needed 3 and shorten height on them.

[@davidhayes1950]

The pannels are tongue and groove and the bead runs round the side but don't bother measuring the bead just scribe it off the aqua panel that you have cut ready to put in and your adhesive should be put on like dot and dap and don't bother putting the nozzle on your adhesive as you need it to come out in big blobs once every 150 mm across and down doesn't have to be a exact and avoid putting the adhesive near the edge as it will squirt out around the edge of the panel but do put the nozzle on the silicone and do a bed of silicone were your gonna place the qua panel which will give you your added protection but make sure you wipe off clear any smudges of silicone/adhesive that get on your board showertray/bath because you want to put a neat bead of silicone on after the install is complete I install these all the time so any questions just ask

[@edenJesuschildofGod8132]

❤thanks

[@sophiemagsx]

Hi , are you in London? Would you fit this for me x

[@KILLUMINATI_MOVEMENT]

No. We are busy!

[@FrankDo65]

ONE HUGE PROBLEM! THEY DON'T HAVE A STORE IN U.S.A?

[@garydouglass9577]

You didnt use your staple gun to the edge of panels.

[@GJLCreativeStudios]

is that what its for? I was wdnering about that

[@davidwoodcock139]

Don’t forget to mark sure the walls are flat and even

[@dejantrifunovic3009]

Sare se ne uklapaju prirodno kao laminat na podu

[@sosolife]

☺️👍

[@Devon-x1u]

BTW I am not watching this to go back to bed i.e. the MUSIC please heavy metal anything but this

[@redguern]

Ha ha! I agree with you.

[@almirhusanovic8128]

I can see anything here

[@martincholman2]

It's not even a bathroom