How to Install Roof Flashing | Pipes, Penetrations, T-Top

[@RoofRepairSpecialist]

Thanks for watching! Let me know if you have any additional tips for installing roof flashing.

[@dkaz974]

Parev from Arizona. Thank you so much. I feel comfortable changing my roof on my workshop because of your explanations.

[@RoofRepairSpecialist]

Parev zes. Glad to hear. Good luck on your project!

[@AndrewCraven-n4g]

AWESOME set of videos on roof installs!!! Thanks SOOOO much!!!! 😊😊😊😊😊😊

[@RoofRepairSpecialist]

Glad you like them!

[@rbahr8214]

Outstanding video. Great job explaining the small details.

[@RoofRepairSpecialist]

Glad you liked it!

[@scott5669]

I've watched tons of these videos and you definitely explain and teach the best..thank you..

[@RoofRepairSpecialist]

I appreciate that!

[@ashishmsukhadia]

Super videos and very thoroughly explained, especially the “why’s” and “what’s”. Thanks!

[@RoofRepairSpecialist]

Glad it was helpful!

[@ashishmsukhadia]

@@RoofRepairSpecialist I am getting ready to get a new roof installed on my house - my first time. So I was trying to get some education on You Tube. Then came across your channel - have viewed several now and now I know EVERYTHING there is to about roofing! 😀 My contractor is not going to be happy! Thanks - great service to the unitiated like me. Best regards!

[@asadadil8695]

Very scientific and up to code!

[@RoofRepairSpecialist]

Thank you.

[@mikecraig9007]

Love your channel. Great info.

[@RoofRepairSpecialist]

Glad you enjoy it!

[@veiledzorba]

What about sticking the cut edge down with a bit of mastic or tar? Being careful to NOT make a dam that would divert water further under the roof. I'm in Florida, need everything as windproof as possible!

[@RoofRepairSpecialist]

Probably not a bad idea. I would still use Ice and water shield I think that'll be most important. Try to find someone local to get advice.

[@gusmarokity6482]

Yes, good idea, in Florida I would use two screws too, galvanized, Above corner area where you got mastic under, half ping-pong, but two inches in from diameter, center. Also, I would use mastic cement around pipe upper area even under ice shield too and on top of every nails left and right of pipe a foot area at least.

[@ErezOvadia]

Which kind of silicone or seal do you recommend to use when the shingles meet the wall ? Thank you

[@xicotencatlvelasco7870]

Good job men

[@RoofRepairSpecialist]

Thanks!

[@mikethompson7436]

So what happens when you install that on a seam and the tar line seals to the bottom of the boot causing tension water to back up during a soaking rain and leak behind the underlying seam shingle 😮

[@THEATREGOD3]

I might be calling you in a couple days I got a situation in Beaumont

[@RoofRepairSpecialist]

Incase you do need us that is out of our service area unfortunately

[@yulinghong1817]

Perfect presentation! Do roofers need to prepare a "cut board" to cut the shingles which need to be cut to prevent hurt another shingles already put on roof on the high slope roofing replacement?

[@RoofRepairSpecialist]

I dont think so, usually a scrap piece of shingle or a scrap piece of wood will do the trick.

[@usatoolengineer]

Really good video

[@RoofRepairSpecialist]

Thanks!

[@DCmite1]

for the vent you used mastic on top and bottom of the flashing for this you recommend ice/water....are they both acceptable forms?

[@RoofRepairSpecialist]

Both are definitely acceptable. I prefer ice and water shield but both work

[@nickpanhead7209]

How is it done with an existing roof, I'm installing a furnace in my garage, and i have to install flashing for a 6" pipe. Its an older roof, not sure whats under shingles. Is there a certain way to install the flashing on to an existing roof. Do you have a video on that. Looked beautiful what you guy's did but im not a roofer. Thank you for your help

[@RoofRepairSpecialist]

I need to make a video on that. But concept is pretty h the same. You just need to remove the flashing first

[@nickpanhead7209]

@@RoofRepairSpecialist ok thank you for getting back to me

[@JahWhiteable]

Yes we’d love to see this

[@asadadil8695]

i think you should cut that felt and adhere the ice and water directly to the roof deck to stick better

[@RoofRepairSpecialist]

That is a good idea. Never thought about that!

[@hondaservicecenter]

No point, especially with synthetic, one hot summer will melt the ice and water base into the underlayment and directly onto roof. Test it yourself. Build a dog house and tear it off 6mo later

[@craig265]

You forgot to add the muffler bearing......

[@RoofRepairSpecialist]

I installed it on the ball joint, lol

[@craig265]

Did you use the jackhammer? @@RoofRepairSpecialist

[@ScottChichester]

Y just y

[@RoofRepairSpecialist]

T not Y

[@ericbstudios9807]

Bro are you kidding? A 4" gap between the shingles over the back of the pipe. Cmon now

[@RoofRepairSpecialist]

Whats going to happen?

[@ericbstudios9807]

@Roof Repair Specialist we're not just battling the rain here...there's ice backup to contend with

[@RoofRepairSpecialist]

Ah, that makes sense. I know Ice & Snow are something I know nothing about.

[@ericbstudios9807]

@Roof Repair Specialist understandable...roofing in NE Ohio has given me that experience I suppose. The ice guard you put over the pipe flange was awesome....the thing is: ice can expand up under the shingles, keep expanding and eventually break the seal and then you have shingle blow offs once a decent wind comes through. Take care

[@RoofRepairSpecialist]

I'll stick to California :)

[@LifeIsGoodThankYouGod]

how do you do flashing for a stucco wall ?

[@RoofRepairSpecialist]

Counter flashing.