To install the wireless backup camera on the tailgate of the CR-V
Пікірлер: 100
@computersshot7 жыл бұрын
You are the coolest you done this job ...Yet you take it all apart again, Risking damage to your panels again to show us an idea to do this job. You are a good man.
@vcrobison4 жыл бұрын
Thanks for taking the time to do this. I love that you simply explain the process. Thanks to your daughter too for her great camera work .
@xywix2 жыл бұрын
Thank you for explaining which one is positive and which one is negative. I’ve been stuck for hours trying to find a good enough video.
@joeh6666 жыл бұрын
It helps a lot, I am installing the back up camera for my wife's 09 CR-V and this is exactly what I need, appreciated your work man.
@xennonman7 жыл бұрын
Thank you for the video instructions. i just installed similar combo on my CRV. For me, the hardest part was taking the door apart but thanks to your instructions that was not hard.
@davehofmann67905 жыл бұрын
I don't know what people are complaining about. I did buy a trim tool set but otherwise followed your video and it was a lot easier than trying to figure it out myself.
@stephendistaso69476 жыл бұрын
Great video, this just helped me install a new wired camera in my CRV. Thanks for taking the time to do this!
@yinghongcao32756 жыл бұрын
You're welcome.
@baksharp6 жыл бұрын
Thank You, Yinghong Cao. God bless. Kudos to you - I just installed Auto-Vox M1W wireless backup camera in my 2010 Honda CRV following your instructions!. Awesome instructions. Found exactly as you said it!. No issues whatsoever!. Thanks.
@airborne135797 жыл бұрын
Great job. I have a 2010 CRV. With this video, I might give it a trial.
@lodiprideprimitives3 жыл бұрын
What an excellent video. Thank you so much for taking the time to make it and share it!
@jskirwin4 жыл бұрын
This is like the only video out there for this model of car. I referenced it several times - even though I'm installing a wired backup camera (note: there is a port below the light and a hole in the body that will allow you to enter the cabin with the RCA jack). Thanks Yinghong!
@yinghongcao32754 жыл бұрын
My pleasure. By the way, where is the port and hole located? Under the tail light? Thanks
@jskirwin4 жыл бұрын
@@yinghongcao3275 Yes. It is about 5 inches below the tail light. It is about 2 inches wide and 3/4 inches tall. You can easily drill through that. Pull back the inside trunk area plastic panel and you should be able to fish a wire to it.
@yinghongcao32754 жыл бұрын
@@jskirwin wonderful, thanks so much!
@1hjehje Жыл бұрын
I have a Honda 2009 CRV and I just ordered an Android Auto screen with a wired backup camera. Thank you for this video as I am sure that it will be helpful when I do my camera installation.
@bradhenry74377 жыл бұрын
Excellent video. Saved me a lot of time!
@flyingvfan516 жыл бұрын
Thank you! I did this today using your instructions and it turned out great. This is a great video!
@yinghongcao32756 жыл бұрын
You're welcome! Enjoy your DIY technologies!
@ATIK-USA7 жыл бұрын
Thank you so much for uploading this video, you save my money. Thanks again......
@ReneRaffo6 жыл бұрын
This is the same principal for the Honda Element thank you
@koshykoshy92767 жыл бұрын
Thank you for uploading
@knarfsidnal6 жыл бұрын
Thank you. Very clear and simple instructions. I am installing the exact same system to my wife's '09 CR-V. For the power cable pass-through, I will try to pierce a neat hole in the rubber grommet (upper left corner of hatch) using a hot nail. Question: have you experienced any difficulty/failure of the adhesive attachment for the transmitter module: Thank you again.
@seemorevid16 жыл бұрын
About to try this today (3/2/18) on my 2011 CR-V. thank you for the very clear demonstration.
@yinghongcao32756 жыл бұрын
Wish you enjoy your work. The installation shall be same for the 2007-2011 model.
@seemorevid16 жыл бұрын
Successful, except found it very difficult to remove the liner. I got the smaller ones off, then drilled a small hole in the back liner and "fished' the wires through. just have to patch the hole as invisibly as possible. Had a busy afternoon, but got it done!
@yinghongcao32756 жыл бұрын
Congratulations!
@seemorevid16 жыл бұрын
Thanks!
@jamescherry7653 жыл бұрын
This was great. I replaced my backup camera 🎥 no problems after watching your video 👌
@yinghongcao32753 жыл бұрын
Glad it helped. Mine still works great after 4 years of installation.
@yinghongcao32753 жыл бұрын
Just realized it has been 5 years. Can't believe it. Time flies.
@y2k704 Жыл бұрын
thank you this video was very helpful
@xMarkuzx8 жыл бұрын
thank you for the video!
@09876superduper7 жыл бұрын
Great video, thanks to you and your camera person. That looked like my garage, right down the the hanging ladder garage door opener and grass catcher on the wall... wait a minute, I better go check and see if you installed it on my car. :)
@yinghongcao32757 жыл бұрын
Ha Ha!
@09876superduper7 жыл бұрын
Updating to let you know I installed the camera on my car. It was really very easy to install after viewing this video. Thanks for sharing.
@baylorstandsstands79433 жыл бұрын
Thank you. Will be used as guide for me. Been thinking about backup camera
The wireless camera and signal receiving cable are packed in two boxes. Some websites sell them separately. Look carefully if the price is much lower that this one. Make sure it does give you both, not just the camera without the receiving cable. This receiving cable is required to charge and supply image to the GPS. regular GPS power cable won't receive signal from the camera.
@jambreaker89114 жыл бұрын
Thank you
@lightworkerlabs32875 жыл бұрын
Is it possible to install on a 2002 crv? Im not sure cuz the back has the tire on the right side and the license plate is to the left which makes it not centered. I figure maaaaybe possible? Great video btw.
@yinghongcao32755 жыл бұрын
Maybe. The principle shall remain same. You may install it above the license plate on the left, not centered, but still gives you a helpful back view when backup. The key point is to safely remove the plastic panel of the tail door and the light assembly on the rear right side. Good luck if you decide to try.
@brendanzivcic7 жыл бұрын
Thanks for the video. What size socket did you say? 20mm?
@brendanzivcic7 жыл бұрын
10mm worked for me. thanks.
@yinghongcao32757 жыл бұрын
10 mm wrench socket to unscrew the door handle. The screws on the CR-V are all in metric unit.
@kobretti4413 жыл бұрын
Thank you.😄
@davidcastillo13404 жыл бұрын
I have a non-wireless camera. How do I run the cable through the interior until it reaches the dash? Ceiling or floor?
@yinghongcao32754 жыл бұрын
I don't have experience on this. Good luck to you. Some people run under floor mat. Some people run through side panel. Both involve a lot of work and have exposed cable around the dash board. That's why I chose wireless type, in which the cable is hidden inside the panel of the back door.
@y2k704 Жыл бұрын
what was the name of the wire you used and where did you get it from?
@yinghongcao3275 Жыл бұрын
It is Garmin BC 30 wireless camera, and its matching receiver power cable. The product is unavailable now. You might try the newer versions such as BC 50. Here is one from Amazon: www.amazon.com/Garmin-Resolution-160-degree-Weather-Resistant-Wearable4U/dp/B0B4YB4KZB/ref=sr_1_1_sspa?crid=1MXWNEA9EC9WZ&keywords=garmin%2Bbc%2Bwireless%2Bbackup%2Bcamera&qid=1673152425&sprefix=garmin%2Bbc%2Bwireless%2Bbackup%2Bcamera%2Caps%2C137&sr=8-1-spons&ufe=app_do%3Aamzn1.fos.f5122f16-c3e8-4386-bf32-63e904010ad0&smid=AY1YC2BWA3QO7&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUExM0wyNVRVS0FHWUE5JmVuY3J5cHRlZElkPUEwNDYzOTc5Mlg1Q0tQMjE3OEJXSSZlbmNyeXB0ZWRBZElkPUEwNDYyMjg4MzNUOEJUSE1aWUkyRSZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU&th=1
@ThanhTran-op2kl7 жыл бұрын
gio to cai luong
@johnnyappleseed87424 жыл бұрын
That is hard work. How about for a wired backup camera?
@yinghongcao32754 жыл бұрын
The wired camera needs more work. You'll still install camera and drill holes to put cables inside, one cable to connect to reverse power. Then you'll have to run another cable through the wall or floor in the cabin to reach a screen on the dashboard. A lot more work that I don't like.
@billyvlog71387 жыл бұрын
How much for this backup camera?
@yinghongcao32757 жыл бұрын
About USD 140 to 170. You can buy it at Amazon, search for Garmin BC 30 backup camera
@zz12345aaa12345zz5 жыл бұрын
How to connect the wires together? I've never done something like that
@yinghongcao32755 жыл бұрын
You may need a handyman to help. Simple version: you peer off the skin of both wires and wrap/tie the naked wires together, then wrap them with electric tape (black) to prevent shortage. Official version: you buy the wire connecting plugs or solder them together, then wrap with tapes.
@jerryandxh3 жыл бұрын
看到小e的微博,特地来看一下哈哈,曹先生牛🍺!
@yinghongcao32753 жыл бұрын
小e是谁?谢谢他(她)的介绍。您在中国?美国?我做这个视频纯属好玩,希望有人用得着。曹。
@davehofmann67905 жыл бұрын
Why is the green wire positive? Green is usually ground.
@yinghongcao32755 жыл бұрын
That's how it works here. My memory about the wiring is fading away, can't tell you why. Sorry.
@rjs12154 жыл бұрын
What year is this CR-V you are working on?
@yinghongcao32754 жыл бұрын
Model year 2010. It is the same generation from 2007-2011
@gurungoracle7 жыл бұрын
what year is your car?
@yinghongcao32757 жыл бұрын
2010 model, shall be same for the model year from 2007 to 2011. I guess Honda likely keep same design pattern in the new model 2012 to now. But you have to confirm yourself.
@richmaster204 жыл бұрын
I came to see the “wireless” camera installation video
@bobbyg2124 жыл бұрын
It's "wireless" between the back of the car and the display unit in the cockpit. At 5:20 he shows you where the transmitter is.
@sunnymango21014 жыл бұрын
What year of crv?
@yinghongcao32754 жыл бұрын
The year of 2010. It is the same generation from 2007 to 2011.
@sunnymango21014 жыл бұрын
Thank you. Appreciate your reply!
@hoisec20132 жыл бұрын
Es un quilombo...
@RXFINYC2 жыл бұрын
I’m still confused
@dirkdiggler26956 жыл бұрын
It says wireless but yet there are wires, huh false advertising.
@TinoDetres5 жыл бұрын
Wireless in terms of it connecting the camera with the front screen. Eliminating the need for running wires to the front.
@victorbasilio11482 жыл бұрын
Que pesima instalacion
@telhommep7 жыл бұрын
No ground connection !
@yinghongcao32757 жыл бұрын
Ground connection is for high voltage 120V or higher. This is a small voltage 12V electronic device. I believe it doesn't need a ground connection. Actually, even many devices, such as computer charger that uses 120 V power, only have two pins, which means the ground connection is not connected even you have it in the extension cord or wall socket.
@TinoDetres5 жыл бұрын
I'm a professional installer of 25 year plus. DO NOT USE A SCREWDRIVER TO PRY ANYTHING LOOSE ON VEHICLE! USE PLASTIC PANEL, AUTO TRIM REMOVAL TOOLS ONLY. If you look closely he damaged the plastic tabs on the panels and more likely than not, the paint with the screwdriver while removing the tail light assembly.
@vcrobison4 жыл бұрын
Chill. It's a 7 year old car.
@livelongandprosper707 жыл бұрын
in english anyone ??
@ttolhurst6 жыл бұрын
The man's English is fine. Have your hearing checked.
@teunihernandez56336 жыл бұрын
gross
@ThanhTran-op2kl7 жыл бұрын
gio to cai luong
@yinghongcao32757 жыл бұрын
I don't understand Vietnamese. Can you write in English? Thanks