How to Load CDR3 double roller speargun.

[@mickeymouse9654]

WOW! Well done!!! 💪 Proof that technique always precedes strength!! 😃👌👍

[@CoatesmansSpearfishing]

Thanks 👍, In the water this technique is much easier.

[@snowbank9386]

Crazy question please. Can u use one of the dual roller bands for a short shot simular to a conventional speargun. Great learning videos. Thanks

[@snowbank9386]

Will ur double roller run both 14mm and 16mm bands? Thanks, Stan

[@CoatesmansSpearfishing]

Yes both 14 & 16mm But you will need a cuttlefish barrel to carry the 8mm shaft and extra weights needed to handle the 16mm

[@riaanrheeder7621]

Hi Chris what would you say is the best size roller to get too shoot tail out of the kelp at cape point?

[@yulichenlu]

hello Chris, how does a mono roller vs double roller compare in terms or range? does it increase range? or only power?

[@CoatesmansSpearfishing]

They are very similar in speed / power and range if they are using the same shaft. The limiting factor is the rubbers snap back velocity so there is the same max speed both guns will drive the shaft. The difference is in ease of loading

[@yulichenlu]

hello~ thanks for getting back to me. what is the purpose of double roller if it doesnt add power speed or range? is it so thicker shafts can be used? @@CoatesmansSpearfishing

[@nick1luke]

Chris thanks for sacrificing your chest for this video Can you explain why a traditional shark fin shaft with 1 large sharkfin to hold both wishbones would not work with this gun?

[@CoatesmansSpearfishing]

Hey Never Lucky, Ha Ha, my chest is fine :-) The RA handle is designed to fit into your chest. Pretty much the only gun I can do this with. On the question of the shark fin, and both bridles on one fin. This will work no problem at all. And as long as the shark fins are not higher than the muzzle rails you can split them on two fins no problem. I have found that the notches work best tho, and is so easy there is really no need to go to fins.

[@snowbank9386]

Question please. What is the distance from center of roller to the band anchor point on the rob allen roller. Would u use same distance for a dual roller? Thanks, Stan

[@abyss13420]

Hello Chris I enjoy every time we watch your tutorial a passionate expert I would like to have one of your double roller heads where can I get it svp? Merci

[@CoatesmansSpearfishing]

Hey Maremano, If you just want the CDR muzzle pop over to coatesmans.com/shop/ Otherwise drop me an email at [e-mail] if you would like me to make you up a gun for you. Cheers and thanks, Chris

[@eliwaing8977]

Hello Sir.I am from East Timor,that speargun is awesome,What is barrel wins name?

[@CoatesmansSpearfishing]

This is my carbon Step Up barrel🤙

[@eliwaing8977]

@@CoatesmansSpearfishing How much for the gun? Can I order?

[@yd8104]

Hello, where can i get that carbon barrel? or that full setup for that matter?

[@CoatesmansSpearfishing]

drop me an email at [e-mail]

[@michaelkleist9482]

👍👍👍 sharing good tecneic..

[@peterthermocline]

👍 Slick video 💪

[@snowbank9386]

Offsides question, what is pro and con of african brea away rig compaired to normal bungee. If african is better with 3 attachment points, how to build? Thanks, stan

[@CoatesmansSpearfishing]

Hey Stan I will have to do a video, I just use a simple bungee so no extra attachment / weak points.

[@snowbank9386]

@@CoatesmansSpearfishing ok, less is better, thanks, stan

[@andrewkeary3288]

what barrel are you using for the 130 dbl roller? is it possible to buy one living in western australia?

[@CoatesmansSpearfishing]

Hi Andrew, Those are my StepUp carbon barrels, I really battle for supply of the carbon barrels so only sell them as complete guns.

[@andrewkeary3288]

fair enough thanks anyway@@CoatesmansSpearfishing

[@snowbank9386]

The light came on??? I asked about using 1 band on a dual band roller. I'm thinking remove 1 band instead of keeping both on? Also, mako 110 roller aluminum vs rob allen 110 toller carbon. The mako comes with a float attachment, does the rob allen 110 roller carbon require a float? Thanks for the help

[@CoatesmansSpearfishing]

Snow Bank, I do have a few clients that sometimes use just one band. And in certain situations works fine. I can speak for the Mako, but the RA 110 carbon roller is a good gun. Have you seen kzbin.info/www/bejne/r4fOpp5mmZhgq8k If you use my ultra light CSR muzzle the gun is pretty much neutral in the water with a 7mm shaft.

[@snowbank9386]

@@CoatesmansSpearfishing thanks for the reply and video. Once in a blue moon things come together thanks to ur focused and direct videos. Yahooooo

[@dustsnow666]

Hi Chris, Can you please let us know where are you sourcing the rob allen compatible cuttlefish carbon barrel in this video?. Id love to try the CRD3

[@CoatesmansSpearfishing]

hey Dusrtsnow666 This is my custom barrel that I designed and get made exclusive for my guns.

[@patrickvanpraet5487]

@Coatesman's Spearfishing where can I find this gun? Seems to not be on your site?

[@fishhunter348]

Hey Chris, I'm wondering if a 120 double roller with more pretension/shorter rubbers outperform the 130 double roller as setup in this vid. Trying to work out what the best option would be as far as ease of loading and max power and range.

[@CoatesmansSpearfishing]

Fish Hunter. On a 120 if you used 65cm 14mm bands with a load assist you would have more power. In reality tho this 130 with 80cm 14mms is fairly easy to load in the water, and shoots really really well. @williampescasub who as I am sure you have seen shoots the crap out of wahoo and doggies. He uses a 130 CDR3 with 85cm bands. Sometimes longer !!

[@fishhunter348]

@@CoatesmansSpearfishing thanks, good to know

[@joecelorellana7048]

Would like to have one of this here in philipines for wahoo and tuna

[@michaeltripp2149]

Chris, I enjoy your videos, especially on roller set up. Any tips on retaining slip tip cable or spectra for use in double or single roller set ups? I usually use small rubber bands on the shafts, but wondering if you had an alternative you suggested.

[@CoatesmansSpearfishing]

Hey Michael, On the slip tips with cable on shafts that have shark fins. I get a long rubber band, choke it around the stopper ball on the cable and pull back the band to the shark fin. This works well with the big guns. On the drop barbs I have been experimenting with pulling the line underneath the muzzle and wrapping the shooting line over it at the muzzle eye. Still need to film this to see nothing else is going on. But that could be the solution.

[@michaeltripp2149]

@@CoatesmansSpearfishing cheers Chris, i will try that rubber band trick. i have routed my spectra slip tips the way you describe for drop barbs, it seems to work pretty well. i would be interested to see what your video shows. Honestly, i do my best to avoid using slip tips, but they don't have a role in certain situations.

[@benlevine5181]

​@@CoatesmansSpearfishingthis is what I've been doing. Tested it in the pool and had no issues, seemed to work just fine for 3-4 shots. No issues out of the pool either.

[@ukcitizen5341]

Hi Chris, do you sell rob allens already converted?

[@CoatesmansSpearfishing]

drop me an email at [e-mail] and I will send you a price list of the guns that I build. cheers Chris

[@drewkaluskimanalive.7057]

Hi coatsman, can I buy this exact gun in australia?

[@CoatesmansSpearfishing]

Hey Drew, You can order direct from me I do not supply retailers. email [e-mail] cheers

[@mosoklali]

130 with two rollers vs 130 with one roller: what does the extra rubber/roller add to the already very good setup?

[@CoatesmansSpearfishing]

with the double roller you use 14mm bands which you can easily load without a load assist and get more power than just a single 16mm.

[@mosoklali]

@@CoatesmansSpearfishing can the 130 double roller go with 8mm shaft you think? In where i am, speargun shaft is so expensive and the much cheaper option is either 6mm or 8mm 316 stainless steel rod

[@dustsnow666]

Hi Chris, what’s the benefit of using a carbon barrel on such long gun, if I remember well, rollers don’t have to fight barrel warping as much as traditional ones. Great videos, keep them coming!

[@CoatesmansSpearfishing]

Hey Dustsnow666 The buoyancy of the barrel allows for ballast to balance the gun so that it is neutral in the water. This is helpful in many areas, from handling to having to swim the weight of the gun from the depths.

[@nfragala]

Watch your fingers. I just learned that important lesson unloading my new RA 90 Roller...

[@marlongonzalez4804]

Do you salle these gun in ebay?

[@eraldompaz]

Hi, how can i buy a double muzzle roller like this?

[@CoatesmansSpearfishing]

coatesmans.com or drop me an email [e-mail]

[@stevennguyen6325]

How to long 130cm-- rubber 70cm?thanks

[@snowbank9386]

Sorry, i asked anchor distance and did not specify a 110 roller. Thanks, Stan

[@CoatesmansSpearfishing]

Hey Stan, it is almost 110cm The easiest way to work out rubber lengths on rollers is half the barrel +5cm On a 110 use 60cm bands for both 14mm and 16mm. 14mm shoots a 7mm shaft and you can hand load 16mm shoots a 7.5mm shaft and you will need a load assist. For more check out: kzbin.info/www/bejne/r4fOpp5mmZhgq8k