How to Magnetize a Tau Broadside

A 9 minute video looking at magnetizing a tau broadside. Needs 4-3/16X1/16, 2-3/16X1/32 and 6-1/8X1/32 magnets.

[@matthewjones252]

This is one of the best magnetized versions I have seen. Well done and thanks for showing us how.

[@WarhammerDad]

Thanks!

[@quazzap2815]

Great tutorial, now got mine magnetised fairly successfully. Thanks!

[@WarhammerDad]

Great to hear, and thanks!

[@davidma6616]

I just magnetized the crap out of my first Broadside. This was a helpful video! I didn’t use the exact same magnets or method, but it was still an excellent jumping off point.

[@slapsmckenzie9293]

you've done alot of good for the greater good here

[@Virakotxa]

The fact that the algorithm suggested me this, makes me fear what is ahead!

[@craigmac1516]

you can use the 2 mm magnets for the support sytems they are smaller and lighter than the main weapons.

[@WarhammerDad]

Probably. I used the smallest I had on hand and they do fine.

[@RoboticDragon]

I have had nothing but problems with these and found out everybody has had the same issues haha Magnetizing the arms for both variations is a pain, and I secretly dont think GW wanted you to be able to. But ill be darned if its going to stop us. Good Job.

[@WarhammerDad]

Thanks, broadsides are some of the tougher models. Tyranids top it though :)

[@TheCliffstudios]

you could have cut the front of the rail gun off and magnetized the front part and magnetized one missile pod. less magnets more secure and it looks awsome.

[@WarhammerDad]

Thanks. I am always hesitant to cut parts of the weapon itself. Much less forgiving of mistakes. It is a good idea though.

[@Aleksandrgrc]

After I cut off the knobs. I drill all the way through both side torsos. I then put magnets all the way through. So both arms will have opposite polarities. I then fill the edge with green stuff. Making notches so when they dry and you put the arms back on the notches interlock a d hold up the weight instead of sliding downwards. I've done three. I will likely never magnetize a broadside again.

[@Aleksandrgrc]

Also of note. Messiest work in my whole army. But it's under the arms so...

[@weathforjr]

Suggestion: Dremel off the barrel of the rail rifle, then cut the high yield missile pods off, then attach your base magnet on the hull of the rail rifle, and attach magnets to the missile and barrel sections. Less magnets, less work imo. Good video. Thanks for the ideas and securement tips

[@dreadnorth8745]

you're way works the best my guy, thanks!

[@WarhammerDad]

Thanks!

[@georgemoldovan2477]

Very nice models

[@Ellipses_klu]

This is... Really nice

[@wolffirepaladin5]

Can you do a magnetising guide for other tau models such as commander?

[@WarhammerDad]

If my son adds more models to his Army, I will. I am not playing as much 40K the last couple of years...no reason, just moving a lot and not getting into a community yet.

[@plaguebearerbob8882]

Top work!

[@WarhammerDad]

Thanks

[@ancientgear7192]

Can the arms with the railgun stand raised and not point down?

[@TimcoSteve]

Excellent

[@ThePeacemaker848]

Now you need to do a Ghostkeel.

[@warvisiongaming40k11]

great video! greetings mr cool!

[@georgemoldovan2477]

Nice

[@boxwinebanditbwb8903]

Lol I wonder if you can make a affiliate link for the magnets.

[@jackseager7147]

What size magnets did you use in mm?

[@WarhammerDad]

Not sure exactly as I use US standard, but google says 1/8th is 3.17m mm; 1/32 is .79375; 1/16th is 1.5875mm and 3/16th is 4.76mm. I am not sure what mm sizes are typical though.

[@cosmit4250]

Hi I know I’m quite late to this video but wanted to ask what hobby knife you would recommend? Or should I just go for a Stanley knife? I’m mainly looking on amazon but anything is helpful. Thanks

[@WarhammerDad]

I use a generic hobby knife that lets me change out the blades. I picked it up at a hobby store. I mostly use #11 blades. For cutting foam I use a Stanley fat max.