How To Make 3.7V To 1.5V Converter

[@Albaloshi88]

Dear this circuit is very useful for clocks and many more useges Thanks 🙏

[@apnaagritech786]

greate tariq lab , good small circuit to convert from 3.7v to 1.57v .thanks for sharing.👍💯🎁💯💐🌼🍀

[@electrofixtips]

They can be used to provide a stable voltage source for testing and repairing electronic circuits. Finally, thank you for making this video!

[@madhavapranay8727]

It really works i hav old neckband li ion battery 120 mah i hav connected to this diy converter thank you so much

[@irfanbhti7577]

Very simple and easy 👍

[@changuinho2000]

thank you very much, I used this to use a 18650 battery in place of a AA battery, that runs a month and then I have to replace it in a Wall Clock....Then if needed I can recharge them on a charger....I replaced the mosquito rackets with them, always using a box, not soldering into the battery !

[@GangaRam-dj3vr]

Very nice video bro thanks for sharing this video 👍👍👍👍

[@kaunisiapa]

Hi.. what's the differences between (this vid) your circuit compared to the circuit using capacitor/elco.? Does your circuit will last longer with a new 18650 lithium battery compared to circuit with elco.? Thank you.. 🙏🙏

[@willsmith1976]

Boa noite!! Eu fiz esse mesmo esquema coloque no relogio de parede, mas ele está adiantando, cimo faço pra resolver isso ?

[@hrushikeshrath4419]

I have successfully completed this project. But then again I have done a similar project in which the output is 1.47v to 1.53v but the clock is not running but it is running on battery. What shall I do?

[@Megapihal]

Сделал всё как на вашей схеме, при полной зарядке 18650 -4,2в получаем на выходе 1,62в, 3,7в-1,37в, 3,0в-1,05в, 2,50в-0,8в, напряжение на выходе при разряде батареи тоже падает.

[@ВенерХасанов-э6о]

То что напряжение падает, понятно. У меня обнаружился другой эффект. После замены обычной батарейки на 18650 с этим конвертором увеличился ток потребляемый часовам механизмом практически в двое и часы стали безбожно убегать! За 8 часов на 30 секунд. Как с этим бороться?

[@Al3abmizo]

Instead of this circuit use AMS1117 voltage regulator will produce stable voltage and at least 800mah fixed 👌

[@romyasdarrr7026]

Bang klo mau outnya 5volt pakai resistor berapa ohm

[@karelbenda5322]

For a voltage drop from 3.7V to 1.5V it is sufficient to connect 3 diodes in series. On one diode the voltage drop is about 0.7V. (3.7-1.5=2.2V).

[@401uwu7]

Generate to much heat in load...

[@bhoot1702]

Energy waste

[@Aaryandubey8]

Yes it does ​@@401uwu7

[@SwingMotor]

Yes kar sakte ha effectively kaam krega maine kiya ha ye

[@sachinsangwan7]

बहुत ज्यादआ गरम होता है ओर जल भी जाता है

[@alexanderlitvinovs8012]

Чем можно попробовать регулировать направление в схеме? Спасибо.

[@SarangS-bw5rl]

Very informative for beginners like me. Thanks for sharing your experience. Can you share resistances required to get output 1.8v , 2.0v , 2.5v , 2.7v , 3.0v and 3.3v from 3.7v battery Thanks

[@osmandemir7272]

Hello Does this circuit consume any energy while it is at rest? Does the transistor consume a certain amount of energy if the output is not connected somewhere?

[@kinshukpal5540]

Impeccable question

[@terabyteultra1673]

can i use the bc549c if i dont have the 547

[@TARIQLAB]

Yes

[@fortdekoda6685]

What's the difference between this simple circuit and a dc to dc converter

[@pandeyrahul999]

Aapka multimeter dekh k aapka channel subscribe kiya ho Fluke sirf professional k pass hota hai ❤🙏

[@TARIQLAB]

Thanks a lot ❤️❤️❤️

[@dikshitkumarpyne3077]

What will be the resistor value to make 5v to 1.2v converter.

[@mitah1888]

Setelah diuji dengan menggunakan diagram yg tertera terdapat kelemahan yaitu output dari arus yg dikeluarkan sangat kecil, ada beberapa jenis jam yg tidak mau jalan.

[@TARIQLAB]

Increase small value of Resistor 2 connected to GND will increase output voltage

[@hrushikeshrath4419]

How many value resistors should you put in relation to the small value register?

[@DavidCanet]

please Sir, -how to do same project for 100mAh battery 3.7V. I need install inside my Seiko 1.5 volt quartz watch . thank you so mucb Sir. you are genius

[@kikiryki]

Can anyone suggest a similar 3,7v to 1,5v chinese cheap product with low heat disipation in loud (i want to connect a small 1,5v E10 very low light ambient bulb) and minimum consumption in stand-by? Thank you

[@TA-sx4uh]

Lm317

[@tangkasbaru2446]

Good job

[@madhavapranay8727]

Can u make water overflow switch for water tanks so that water stops as it fills

[@johnmonk3381]

Why cant u just use a mechanical ball plunger for that. The one used mostly in toilet tanks

[@edityatalenta3768]

Bos..kl 5v ke 4v pake apa aj komp nya..

[@retroaria]

This Transitor is a PNP or NPN? And how can I do for 2.0V? (not 1.5V) Thanks

[@TARIQLAB]

Npn, reduce ground resistor value, or use 10k resistor to adjust

[@salalasalala9228]

Great tariqlab

[@namangupta86]

Can I use this to run a small 1.5volt motor?

[@TARIQLAB]

Maximum 100 mA

[@namangupta86]

@@TARIQLAB can we also use some capacitor to improve its efficiency and to have a more regulated current?

[@TARIQLAB]

Yes, to decrease fluctuation

[@slingshotsk2231]

Dono resistance mila ke 10k hona chahiye ya ek 10k ka???

[@TARIQLAB]

Aik 10k ki

[@mrgreen3319]

Can we use this circuit for trimmer motor

[@TARIQLAB]

This is only 100mA, if consumption below 100mA then ok otherwise use any higher current transistor

[@mrgreen3319]

@@TARIQLAB if i add a capacitor would it increase its MA

[@TARIQLAB]

No

[@mrgreen3319]

@@TARIQLAB then how to increase its MA... which current transistor shall i use

[@HotelPapa100]

@@mrgreen3319 This heats away excess voltage. You will need a transistor rated for the wattage and a heat sink.

[@adilbangashofficial]

Agar may 1.8 v banao os k liye kya kar na hai

[@TARIQLAB]

Collector side ki resistor 8.2 k se 9.5 k ke middle main rakhen

[@adilbangashofficial]

@@TARIQLAB hum ko 1.8v bana hai

[@brengoscadong6934]

Klo led 3,7 volt pakai baterai 3 volt gmana caranya bang

[@mahd2dz]

sir can i use S8050d npn transistor

[@TARIQLAB]

Yes, but s8050 pin 1 is emitter 2 is base & 3 is collector

[@mahd2dz]

​@@TARIQLABthanks i used bc547 i have it but I don't reach to 3.0v output 😢 what's the resistors give me that voltage "3v"

[@TARIQLAB]

Increase the value of base to GND resistor

[@apaskalss5159]

thank you sir

[@user-pd1cr1kk2k]

How to convert 3.7 to 3v?

[@TARIQLAB]

Use a diode in series that will drop 0.5-.0.7v

[@helloeworld153]

will work on transistor 13003 ?

[@TARIQLAB]

13003 is 700v transistor, not suitable for low voltage

[@zaidlatifqureshi4542]

What happened if we connect direct 3.7v instead of 1.5v in wall Clock......?

[@TARIQLAB]

Damage the machine, maximum u can give 1.8v

[@zaidlatifqureshi4542]

@@TARIQLAB 👍 Thanks

[@RinkuNagar-gp4we]

Sir trimer moter run kre is tra ka koi cericit banavo 3.7 volt battery se 1.2 volt out put ho

[@TARIQLAB]

Trimmer main wesy 1.2ki battery hi use hoti hai, ye transistor 100mA ka koi ziyada mA ka use kar len

[@praneetbhargava5886]

4.2 se 3v bhi ban skta hai kya

[@TARIQLAB]

Yes

[@jagseer_machenical]

Resistence wat ??

[@TARIQLAB]

1/4W

[@sadektako2845]

i have the bc 548 ,it is valid ??

[@TARIQLAB]

Will work

[@sadektako2845]

@@TARIQLAB choukrane .............../

[@Al3abmizo]

Not reliable and will not produce the required Amper to run the attached devices beside heat. Solution? Use a voltage regulator like AMS1117 with your required voltage like 1.2v 1.8v 2.4v 3.3 etc. it's perfect and output fixed stable voltage and about 800mah without any heat. 👌

[@hbtech6376]

Not working at all... I have a hearing aid operates on 1.5v I made same circuit but not working, when I connect the multimeter for voltage check it shows many useless numbers Don't know why but this is not useful for some purposes.

[@TARIQLAB]

Ur input voltage?

[@maungmaungtint8572]

It is ok. Thanks

[@shafi.j]

5volt to 3.7 volt charger with lm317 circuit video post

[@TARIQLAB]

Soon

[@govind3170]

Resistor watt?

[@TARIQLAB]

1/4 W

[@trajcem]

Current is too low! Clock cant run...

[@sayyedindia003]

اس میں بجلی کتنی ضائع ہوگی؟

[@TARIQLAB]

نا ہونے کے برابر

[@thanos9816]

Sir maine 3.7 v ko 1.5v badl diya but ampere bhi 1.5amp se 0.06amp hogyi mujhe 0.5amp chahiye kaise hoga please reply??

[@TARIQLAB]

Ye transistor 100mA ka hai koi bara transistor try karen

[@mrgreen3319]

@@TARIQLAB pnp or npn transistor use karna hain

[@Fransisko99]

Bagaimana kalo 5volt to 1.5volt bang?

[@TARIQLAB]

saya telah memuat naik video 5v hingga 1.5 pada saluran saya

[@crazymafia9790]

I usd bc 548 its working or not

[@TARIQLAB]

Try if difference in voltage then change in resistors value

[@rudypow182]

Resistor berapa watt?

[@TARIQLAB]

1/4 watt

[@CreativeNS0025]

kzbin.infomDAIsjS-6b4?feature=share

[@jmljl7077]

Bang mau tanya,untuk Transistor BC547 yang jenis: PNP apa NPN ya trims?

[@TARIQLAB]

BC547 NPN, BC557 PNP

[@jmljl7077]

Ok trims,untuk resistor-nya 10K yang berapa watt bang ya trims?

[@madhusudandabral6103]

मुझे समझ मे नही आया की bc 547 को वोल्टेज ड्राप के लिए कैसे यूज़ किया जा सकता है....मैंने बहुत सर्किट बनाये है जिसमे bc 547 को वोल्टेज इम्प्रोव के लिए लगाया गया था तो इस सर्किट में वोल्टेज ड्राप कैसे हो सकते है ....और दूसरी बात कई सर्किट में bc 547 के बेस पिन पर +v दिए जाते है और अमीटर पिन -v दिए जाते है और out put कलेक्टर पिन से ली जाती है पर इस सर्किट में कलेक्टर पर - वोल्ट दिए गए है ....समझ मे नही आया कुछ की हो क्या रहा है

[@TARIQLAB]

Base pe voltage kam ziyada karny se output emitter pe voltage kam ziyada hoty hain

[@MUHAMMADnehal9577]

Sir detail ke sath nhi bataya apny

[@idikutt34]

Thank you

[@TARIQLAB]

Welcome

[@aajkitazakhabar8785]

Please, make 1.5 v to 3.7v

[@gopikanaparthi749]

How To Make 3.7V To 3.0V Converter

[@TARIQLAB]

Just use 1N4007 diode, this will drop 0.7v

[@freemotionbyshorifbd2195]

ট্রিমার চলবে এটা দিয়ে

[@TARIQLAB]

Yes

[@fernandomaldonado599]

Hice el proyecto, y cuando lo conecto ami teclado inalambrico cae el voltaje de 1,5 v a 700mv una lagrima jaja

[@100roberthenry]

tried it, not enough current to run a small 1.2v set of solar string lights.

[@TARIQLAB]

BC547 only 100 mA max

[@magomedguppoev8213]

красава.

[@humdardi.]

Bc 547 transistor pnp or npn Kay lagay...Bhai e to kaho

[@TARIQLAB]

NPN

[@parameswarmandal8840]

Not same current output.

[@TARIQLAB]

Why,