How to make a DIY LINE SPOOLER for Cheap!

In this video I attempt to make a customized version of a DIY LINE SPOOLER.
Materials used: 2x6 board cut to approximately 11.5 inches
1x4 board cut 2x for approximately 9.5 inches
Medal screw rod 15 inches
5 to 6 nuts to match your screw rod diameter of choice with about 10 washers to fit the diameter.
2 springs that are big enough to allow for tension on the bar. make sure it doesn't touch the bar or it wont create tension.
Visit www.mattsfishingadventures.com
Check out our facebook shop, click the shop tab to support!
/ mattsfishing. .
/ mattsfishing. .
To help Fund My Fishing and Film Making Habit we now Have a
Patreon!
/ mattsfishinga. .
Follow me on my social platforms i post just about anything on there and you can reach me there the fastest .
Follow me on facebook
/ matthew.vala. .
Facebook group
/ 92833. .
Follow me on Instagram: / mattsfishin. .
SnapChat: / matthewva. .
Facebook Fan Page: / mattsfishing. .
Twitter:
/ mattsfishingadv

[@clarkriccobuono3903]

You can C clamp to your table too.

[@johnbuschman8815]

Good job I like it

[@redladyfish4201]

Awesome idea, very handy.tight lines!

[@americanpatriot661]

Gr8 idea! getting ready to spool up some reels myself. Good luck on the sailfish trip bro can't wait to watch the video.

[@50shadesofblue24]

Great video bud!

[@federicocabarle713]

pretty great now I have to make a trip to home depot try using c-clamps and clamp it on the table.

[@MattsFishingAdventures]

Yes sir it definitely works and its budget

[@yangjianhunt]

Nice design, Matt!

[@MattsFishingAdventures]

Thanks were you able to understand the setup? Video was kinda ehh lol. Messed up a little and fixed it up on the editing.

[@yangjianhunt]

@@MattsFishingAdventures Yep I definitely got the idea. :)

[@mrBDeye]

Items needed for this project...You'll need one pencil and one brother to hold the pencil.

[@alfonsom2385]

Video was unclear i now have a pet shark in my room

[@octyl95]

Quick tip maybe you should buy a Dewalt or Milwaukee drill see you had some problems at 2:30

[@equinoxfishingteam5837]

Great job Dude!!!! Congratulations from Equinox Fishing Team....

[@Nick_Tag]

Master at work :) was the mistake basically to use two nuts on the right side as well?

[@MattsFishingAdventures]

Don't think it was much of mistake. I've had that same spooler for a couple of years and I still use it and ill let you know that it spools braid so tight how its suppose to be put on and I'm super impressed with how everything works.

[@larrytwiner]

Yes, I believe that is what he changed. The washer was causing the single nut to spin with it, but with the second nut locking in the first nut it won't move with the washer. At least that is what I got out of it.

[@JCS1956AZ]

You could make that a quick release/quick load if you cut the tops of the holes open, so all you had to is loosen the nuts and lift out the whole shaft and reel. Or did someone already suggest that?

[@MattsFishingAdventures]

That's a good idea 💡

[@bigbamboo936]

Dread, the inner nuts were not necessary. Due to your washers you could adjust the tension just from the outer nuts. Other than that, not bad.

[@charlesmurray1220]

Challenged.

[@piercedwyer5040]

mate get some good tools

[@williamster2015]

You could have done this much easier by literally doing 50% of this build, Image it as the letter "L". Two washer, spacer and locking nut on the exterior side and interior side. Followed by a flange washer then your string, another flange washer, , a flat washer, your spring another flat washer and a Locking wingnut or a cwibg nut backed with another nut

[@zachshott7833]

You actually have to PUSH when trying to drive a screw....

[@brentnanita3939]

I dont mind a shop fee if they would do a professional job. Most guys they have doing it do a crap job. I dont trust them to do my braid, esp tie my knot on the spool.

[@robertrook2714]

You have officially lost your man cardb

[@matejjurisic11]

Wtf are you doing?

[@MattsFishingAdventures]

Making a KZbin video! What are you doing?

[@ShutUpNFish1]

Dude! This was horrible….get you some better tools too!😂