How to make a Drone Using pixhawk flight controller Part-1

#diydot3d #pixhawk #drone #build #diy #rc #droneframe #diydrone #flightcontroller #matek #powerdistribution #dronemotor #droneframe #gps #flysky
How to make a Drone Using pixhawk flight controller Part-1
Join this channel to get access to perks:
/ @diydot3d
Follow :
Facebook: / diydot3d
Instagram: / diydot3d
Twitter: / ddot3d
💙❤💙❤💙❤💙❤💙❤💙❤💙❤💙❤💙❤💙❤

[@Stortion]

the first video with a clear walkthrough of the Pixhawk/flysky setup. I thank you so much for this

[@DiyDot3d]

Thank you🙏

[@vineetbatra2037]

Good efforts to teach making drone....Thanks dear

[@OCDer]

thanks very much sir, this content so great knowlegde, greetings from indonesia student electrical engineer

[@MidEats]

Please go through the detail inspection of PID tunning

[@НикитаДавыдов-о7ъ]

Thank you very much! I tried to build drone using APM 2.8 recently. But it bent to the left all the time so drone flipped at the start. I have been struggling with that for months. By some reason I was sure that controller is alright but week ago I discovered that one of the outputs doesn't work correct and motor that is connected to this output doesn't rotates if you check motors through Mission Planer at 5% thrust. Now I will try to build drone with Pixhawk. I am wondering why so many people make drones with APM because there is always problem with external GPS and it is also quite an old controller now. I wish I knew it in advance

[@curlybracket]

king🔥

[@uus]

Why you don’t calibrate esc from mission planner?

[@aredits7311]

Hi bro I'm doing project on drone at first i have used the Arducopter the issue i was faced is that it was not stable it was lifting up vertically but while lifting vertically it was moving right and left without any movement in direction channels and now I'm using Pixhawk flight controller and the Same issue i am facing with Pixhawk also. So please can you help me in stabilization of drone using Pixhawk

[@siddharthkosaraju670]

what battery did you use? and when you showed the power distribution module, there were wires soldered to the lipo and 3-4s ports of the power distribution module, where did you get that wire from?

[@DiyDot3d]

Lipo will power the pixhawk power module and power distribution board

[@user-cf8sq3ck2j]

I saw that kind of drone on aliexpress. I am planning to buy one and your video will be of great help. I want to know the durability and is it worth to buy it ???

[@ricardoaguiar4823]

Hi, I have pixhawk 2.4.8, I should update with "Pixhawk1" or "fmuv3", would you know the difference between these updates?

[@HungNguyen-bk1jn]

Where in pixhawk i can connect camera?

[@kislaytripathi4873]

Bro I have done all the connections and also calibrated the drone in mission planner and also calibrated the remote but still my drone is not responding .. Please can u help me we are working for a drone automation project in our college

[@sapnakulkarni9413]

Uncle hi I met you in ground 🥲🥲🥲🙏

[@vinireddy386]

bro after esc calibaration imgetting continuos beep sound so wt to do stop it ..??

[@DiyDot3d]

May be esc still in programming mode.check esc manual to configure

[@skymavericks]

Bro at radio calibration, my Trasmiter are not working, not showing any values

[@DiyDot3d]

Hi. Check connection to flight controller from reciever , may be you connected wrongly

[@skymavericks]

@@DiyDot3d okyy bro , but one more thing after esc calibration . 2nd time motor not start. And also fail safe value not edit . I have 3s battery but in failsafe showing 4s . How can I correct ?