How to make a Feature Ring

How to make a Feature Ring

[@billgiles3261]

Great technique, thanks for sharing.

[@SilverBack.]

nice work 👏👏👏

[@turkeycreekknives133]

Very nice lots of cutting glueing clamping

[@chriswalters5936]

hey tommy i had to get a new tablet a while back so i had to subscribe again just to let u know my friend. chris

[@jonsxln]

Great video Tommy. Love the design and technique. Subscribed…

[@myvoodooisstrong]

Nice work

[@Tommyakridgedesigns]

Thanks

[@PopsShop]

Thanks for the video. I am new to Woodturning and watch as many videos as possible. You always have informative videos. Thanks so much. Danny Sweet

[@Tommyakridgedesigns]

Thanks for the comment and for watching

[@bradleyswiger6050]

I love,, making one for me and my son. Hope God guides my had as he did yours.

[@jasonenz4238]

End result was absolutely exquisite!!! Great job bud! Haters gotta thumb down in jealousy. Take those thumbs down as a compliment...

[@Tommyakridgedesigns]

Thanks Jason

[@cmarkme]

Beautiful, I Love the Cross Design.. Made me Teary, thinking of my Late Wife :-)

[@petervanrensburg4171]

Very nice Tommy, thank you for sharing

[@Tommyakridgedesigns]

your welcome

[@roberthornwoodturner]

Thanks for the how to. Well done.

[@Tommyakridgedesigns]

glad I could help

[@lynbren]

thanks for sharing that good job

[@Tommyakridgedesigns]

Thank you Lynn

[@brianroberts6751]

Nice work. Good directions to follow. Thanks.

[@Tommyakridgedesigns]

thanks

[@reesh28]

Do you use measurements when making your bowls (segmented rings) or are you freestyling it. How do you know how many segments for each size ring? Thanks and love your videos!

[@Tommyakridgedesigns]

I freestyle, I just change the how long I leave the outside of each wedge. An 1/8 of an inch will increase the ring a good bit.

[@keithsshop6559]

Very nice vessel.

[@Tommyakridgedesigns]

thank you

[@turkeycreekknives133]

What where the dowels for set up for two ring layout

[@aaronbarton4140]

so was the urn at the end the one u made or the one u were trying to make ?

[@redkite200]

What were the two dowels for? I noticed you put them in when you glued it up, but they seemed to be gone when you came back to it when the glue set.

[@Tommyakridgedesigns]

Sometimes when you glue up the pieces they don’t quite match up so if you glue up the 2 half’s and place a Dow between and let it dry, you can sand the 2 half’s later so that they match.

[@redkite200]

@@Tommyakridgedesigns Thanks for that Tommy. Finished job looks superb. I just wondered if I had missed a step in the process.

[@17hmr243]

would be nice to see what your making be for you move on to the turning just thinking out aloud

[@Tommyakridgedesigns]

I have a hole video on this piece found here kzbin.info/www/bejne/l6C4oqiqj7CEiKc

[@thelettertsix]

nice, good work brother.

[@Tommyakridgedesigns]

Thanks

[@seeingdragons4319]

A bit of a leap in the end there, don't you think?

[@ErikAnderson1]

Nice Video and a nice Urn and great tutorial on the feature ring! I subscribed and liked, if you get a chance check out my channel too. Thanks Tommy!

[@Tommyakridgedesigns]

+Erik Anderson Thank you Erik, I have been a subscriber of your channel for a long time and I have seen every video you have done. I even sent you some money to help your mom, is she doing okay? Thanks for subscribing and have a great day, Tommy

[@starkaran8390]

I did it myself. I used Woodglut woodworking plans for this.

[@bradleyswiger6050]

I'm not a great typist and a worst proof reader. Suppose to be it and hand.