How To Make A Hat Rack - SIMPLE AND EASY DIY

Рет қаралды 82,730

RaCo Woodworking

Күн бұрын

Пікірлер: 33

@tomfrank5326 3 жыл бұрын

This worked great. I made one for my son as a Christmas present this year.

@gdprun 2 жыл бұрын

Great job- that you. i think I may make one for my brother in law. He has a lot of hats!!

@wahinenuiloa 7 ай бұрын

Great video. Thanks for posting🤙🏾

@sandEffect 2 жыл бұрын

Super clever and easy. Great video.

@whalens7069 4 ай бұрын

Just made one thank you!

@Apb23 4 жыл бұрын

You make it look easy... but I think it’s hard for most people! I like the music.

@racowoodworking147 4 жыл бұрын

It is't really that hard, just have fun with it and give it a try.

@racowoodworking147 3 жыл бұрын

You can make it look easy too, just take your time and follow the steps. If you make a mistake, start over...keep practicing. The more you work with your tools, the better you understand them.

@markbendall1 2 жыл бұрын

Hi, thanks for taking the time and effort to make this. I would like to see the logo on the front of my caps so I noticed when you put your cap on this it also took up the slot below it, in theory you could only cut 5 slots to show 5 caps fully? Another video? lol

@brianholt6083 2 жыл бұрын

Pretty nice

@ralphkopkowski6813 2 жыл бұрын

Can I get a copy of your template to make the holes for the rack

@B_man12345 10 ай бұрын

I was thinking the same thing. You could adjust watch the video step by step I might do that to make my own I like this idea

@RYBRENG 9 ай бұрын

He has a link posted in the description

@ronash9918 13 күн бұрын

Can you make one and sale it

@ryankirby5141 3 жыл бұрын

Gotta subscribe just because the AVS banner!!!!!

@racowoodworking147 3 жыл бұрын

Thanks...Go Avs Go. They have a good team this year, hopefully they can go all the way.

@ryankirby5141 3 жыл бұрын

RaCo Woodworking I hope so. They need to open back up so I can make the trek out to a game from SLC

@jdw1407 2 жыл бұрын

whats the spacing between holes?

@J123G 2 жыл бұрын

I printed out the template pdf and it didn't print to scale based on what width board he was using. Based on another youtube design I would guess about 4 inches (100mm). The hole he drilled is larger than the other youtuber design but my guess would be a 1.25 to 1.5 inch hole with a slot .75 to 1.0 inches. The angle used here was 45 and I think that is OK. The spacing between vertical racks should be about 1 inch (or wider) than the typical ball cap width.

@richardscott9158 3 жыл бұрын

How do I make a template?

@denniscabral4487 2 ай бұрын

You never said how far apart your pilot hole is away the very first hole how far apart are they 6 in 8 in 4 in you said you had a template down below the Templeton tells how far apart the holes are

@ajrchops83 Жыл бұрын

Since you used a template. It would be helpful if you gave more measurements- Hole circumference. Where the holes are, you said center but they’re clearly not- ? You did say one each thick spacer….

@storedaway 6 ай бұрын

He did mention the bit was 1 1/2 inches.