How to make a silver foxtail bracelet | DIY chain

[@JulianaKersten-mg5ni]

Thank you, finally someone teel the size of the wire and the mandrdl

[@pemj7360]

Thank you for making this video and explaining everything. And not speeded up .

[@maxattack5772]

What a beautiful bracelet you made!

[@margaretyoung9169]

Loved it after you highlighted it!

[@watchclubent.3956]

Hey please make more bracelets tutorials, thank you for your vids

[@kevinf6927]

Amazing thank you for creating this video, I have watched both video's with and with out audio , thank you very much for creating a video with the step by step audio

[@MadebyLeth]

Thank you for your comment it means a lot to me! And I'm glad you liked the video!

[@michelleg773]

Very beautiful bracelet! TFS 😁

[@tommtommkin]

Wow that is fantastic. Thank you so much for this I love it.

[@jaredchadwell7233]

Beautiful work! If your wire size was 0.8mm and mandrel was 14mm am i correct in calculating the aspect ratio to be 17.5?

[@JustME-ft4di]

Wonderful!

[@Bratmouse1]

Nice! What is that plate with the square holes where you pull the bracelet through? Thanks

[@MadebyLeth]

Thank you very much. It's called a draw plate, which is made with specific hole sizes, so you can stretch wire or, in this case, make the bracelet uniform in size.

[@donnaOdesignsJewelryArtist]

Incredible video! Beautiful bracelet. How thick is the finished bracelet?

[@MadebyLeth]

Thank you! The final bracelet is 4 x 4.5mm thick.

[@shizzydeep6867]

Where did you get the silver tubing from?

[@Infoacc24]

Hey, great work. What do you use as flux?

[@oeildeserpent5103]

Yes, super.

[@emilymalcolm87]

Amazing piece 🔥 what size are the jump rings you are using?

[@Nathan-ou2yg]

It says In the beginning

[@dragonshoarddesign3094]

What is the name of the the tool at 8:19 it was not in the description list? I am also a jeweler that would be very handy cutting stock for sizing or anything.

[@MadebyLeth]

I'm sorry it's not listed, the tool is called a 'Tube cutter'. I'm including an Amazon link to one so you can see what other names it goes by, I hopes this helps: www.amazon.com/Jewellers-Tools-Cutting-Cutter-Jewellery/dp/B017MONPSA

[@shellycristiani5339]

Beautiful bracelet Leth. What gauge is the silver? What is the diameter of the jump rings?

[@MadebyLeth]

Thanks, Shelly! The silver wire is 20 gauge/0.8mm and the jump rings are made on a 14mm mandrel.

[@ДенисКириянко-г9ф]

Красиво, а чем паяете и как называется металл? Ответьте пожалуйста

[@aleksanderwojcicki492]

Its silver and he is using silver solder i think

[@sharda2073]

Can we hammer instead of taking it out of the box steel plate

[@MadebyLeth]

Hello Sharda Yes, you can. The advantage of the draw plate is that the chain becomes very uniform, quickly. You will also be able to use a rolling mill if you have one. However, you can of course also do it with a hammer and make it just as uniform.

[@kameshrajendran4431]

Sir If my wire gauge 0.60 wats my mandrel size ?

[@MadebyLeth]

The silver wire I used in the video was 20 gauge/0.8mm and the jump rings are made on a 14mm mandrel. If you use 0.6mm silver wire you can still make it on a 14mm mandrel, however, it will be a bit looser. You can also use a slightly smaller mandrel size like 12.5mm or 13mm to make it tighter.

[@siddharthsahni6600]

Is there any way to connect with you?