⚠️Attention⚠️ USE 6.5v Transformer For 230V Output 12V Transformer for 110V Output Hello friend 🔻 (((Part-2 ))) kzbin.info/www/bejne/fICyfoprpKp8sJIsi=KwdABPGlosyFquti Please switch to 1440p to enjoy clear video
@prasadbodas20009 ай бұрын
Do the chip ir2113 heat up during normal operation? On the board that I purchased only one of the two chips heats up even when MOSFETs are not connected and egs002 board is only powered up by connecting 12v, 5v and ground voltages. Please help
@Electronic_For_You9 ай бұрын
No , The Mosfet driver should be at normal temperature 30-40°c, check the connections , if there is any micro short on track that can conduct current, or maybe your mosfet driver ic is damaged
@Avi-Dixit5 ай бұрын
Watched approx 250 videos on pure sinewave inverter using EGS002, but never seen such a wonderful video with proofs(Using Osciloscope). Thank you Sir🙏 (Mzaa aa gya video dekh kr :) )
@Electronic_For_You5 ай бұрын
You are welcome, I try my best 😊
@Avi-Dixit5 ай бұрын
🙏
@Avi-Dixit5 ай бұрын
@@Electronic_For_You Sir...Sorry for disturbing you..I've a little doubt about the capacitor(35v 1000uF) you used between H-Bridge, ...I actually want to know the points where capacitor is connected, ...is it connected on Low-side-mosfet-Source pin to High-Side-Mosfet-Drain pin?... Sorry for my poor english🙏🙏
@Electronic_For_You5 ай бұрын
It's connected to + and - Voltage source
@Avi-Dixit5 ай бұрын
@@Electronic_For_You Thank You Very much Sir 🙏
@hp2073Ай бұрын
Can I use this with a 12V battery and a 6 to 220V transformer? I want to make sure using a 6V transformer instead of 7V does not bring more than 220V at the output, because maybe reducing the duty cycle using the feedback only limit and compensate this to some level.
@Electronic_For_YouАй бұрын
Hello, It's best to use the Old Computer UPS Transformer, it's suitable for this project! But use only 12v ups transformer not 24V 👍 I got old ups for only $2 from the junk yard, It's cheaper than buying a new one!
@hp2073Ай бұрын
@@Electronic_For_You I want to use a 12V battery and a 6V to 220V transformer, because it is easier to find. my battery is 12V not 24V
@Electronic_For_YouАй бұрын
That is what i was saying, Use a 6V transformer for 12V power Source , Suitable transformer for this porpoise can be found in 12v UPS, and i mentioned about Ups not battery (24V ups transformer is not usable) 👍
@hp2073Ай бұрын
@@Electronic_For_You okay, I just though you misunderstood my question. so you confirm using a 6V transformer instead of 7V or 9V will not cause over voltage at the output, right?
@hp2073Ай бұрын
@@Electronic_For_You also is there any advatage of using a heavy transformer instead of switching method?
@sepideh956517 күн бұрын
Can i use a transformar with higher rating, for example 1000 w for this 300 w inverter?
@Electronic_For_You17 күн бұрын
Yes , You have to use more MOSFETs
@sepideh956517 күн бұрын
@@Electronic_For_You thank you 🙏
@Electronic_For_You17 күн бұрын
You are welcome
@pp-ch3jq3 ай бұрын
I have been able to replicate the circuit with your assistant. I got 223 Vac as output with sine wave from 24V battery input to a 12-0v to 220 transformer. But I've not loaded it yet because I did everything on a breadboard. What I discovered is that you have to follow the circuit strictly before getting desired result. A single missing capacitor can affect the result. More so, the wiring should be done so that the size of the transformer will not affect the egs002 module performance. Start with a very small transformer.
@Electronic_For_You3 ай бұрын
Very good job 👏 See the circuit is definitely working and not fake ! Good luck, be careful EGS002 is a very sensitive module!
@SHUBHAMROHILLA-ed4vg3 ай бұрын
sir can you pls help me also i am confused how to connect capacitor 1000uF in the circuit which is shown in the video and the value of choke filter inductor use
@Electronic_For_You3 ай бұрын
Capacitor is connected to + and - vcc and chocke is from old CRT TV no needed if you don't have!
@SHUBHAMROHILLA-ed4vg3 ай бұрын
@@Electronic_For_You sir what is the current rating of your transformer
@Electronic_For_You3 ай бұрын
30Amps
@hp2073Ай бұрын
in some circuits, they use a big inductor before the primary of the transformer, I mean between h bridge output and the input of the transformer, why?
@Electronic_For_YouАй бұрын
For filtering,
@truejaguar73706 ай бұрын
Sir i made this inverter the output voltage is 225v ac which is ok but the feed back rectified voltage is only 200v dc is this ok? because it can't power a 100w load
@Electronic_For_You6 ай бұрын
Is your transformer windings are 8V each? And you used 230V
@richkhalifha2466 ай бұрын
Can u share the circuit diagram
@Electronic_For_You6 ай бұрын
It's in video
@hp2073Ай бұрын
how do you calculate the maximum output power? I think your transformer is around 10A. so you should get 70W power, is that right?
@Electronic_For_YouАй бұрын
My transformer is 30Amps
@hp2073Ай бұрын
@@Electronic_For_You how much is the standby current consumption (no load at the output of the transformer) at the input?
@Electronic_For_YouАй бұрын
1 amps,
@hp2073Ай бұрын
@@Electronic_For_You is this natural or can this be improved?
@Electronic_For_YouАй бұрын
Its common for sine wave inverter
@pesineengineering16 ай бұрын
Hi sir, thanks for the good work. What's the capacitor voltage at pin 15? Its just indicated as 4.7uf but no voltage, please help
@Electronic_For_You6 ай бұрын
50V 4.7uF
@samueladitya17294 ай бұрын
can you instead of using transformer, use high frequency 12v to 300v dc, and the high voltage directly feed the mosfets
@Electronic_For_You4 ай бұрын
I have video on this topic
@Zikeyboy1016 ай бұрын
Hello, I need your help, I have build this same inverter using your video, but my mosfet blows immediately. I have used IRF3205 mosfet and 7v-220v transformer. I have followed the schematic exactly, but my mosfet always explode. Please help
@Electronic_For_You6 ай бұрын
I think there was some connection fault, 😕 You should always contact a low power source first for testing like a 12V 2A Adaptor, And another thing is your module OK? Mosfets will explode if the Gate Driver IR2110 fails!
@Zikeyboy1016 ай бұрын
I have ordered for another Egs002 module, and irfp260n igbt. I will retry with the new components and give you feedback
@Electronic_For_You6 ай бұрын
Goodluck, Use 12V 2A power supply for first startup, so if there is any fault, nothing blows up
@The11kvexperts3 ай бұрын
I copy your full circuit except choke filter inductor which you mentioned it is not necessary and i am only getting output of 62V at 9W led as a load and 90V at no load I am trying the circuit from one week pls suggest.
@Electronic_For_You3 ай бұрын
What is the voltage rating of your transformer? Use a 6V UPS transformer
@The11kvexperts3 ай бұрын
What is your battery rating
@Electronic_For_You3 ай бұрын
I used a power supply
@The11kvexperts3 ай бұрын
Ohk your power supply voltage & current rating bcz I am also using same 12V & 4A .
@Electronic_For_You3 ай бұрын
Mine is 12V 20A
@nareshshanmugam33976 ай бұрын
I bought this module with display,but this display show nothing,what is the problem,please give some suggestions
@Electronic_For_You6 ай бұрын
Check 5v available in display or not
@Zikeyboy1016 ай бұрын
What is the number of your gate diode? It doesn't look like 1N4148
@Electronic_For_You6 ай бұрын
I used HER207 Diodes
@Zen2ncd3 ай бұрын
Sir, can i use 600va ups transformator?
@Electronic_For_You3 ай бұрын
Yes
@fakhrealam2008Ай бұрын
Awesome job, love it.
@Electronic_For_YouАй бұрын
Thanks ✨
@edilbertovanegas33989 күн бұрын
Exelente video estoy con ganas de hacerlo podrías facilitar el diagrama?
@Electronic_For_You9 күн бұрын
Hello, Please check the video description
@sepidehshabani-zd4lh4 ай бұрын
hello, thank you for your video, first i want to test the inverter without transformer to see the inverter output voltage value, after that i want to buy a transformer according to the output voltage of the inverter. how can i test the inverter?
@Electronic_For_You4 ай бұрын
And also use 12V 2A Power supply at start-up if you don't have lab power supply
@kalashnikov_47z9 ай бұрын
Another Great project 👏🏼
@Electronic_For_You9 ай бұрын
Thank you! 😊
@scorebetter37095 ай бұрын
I need help my output voltage is 8.41 volt AC but when I connect to 6-0-6/220 v transformer I'm only getting 110-113volt what to do??
@Electronic_For_You5 ай бұрын
Hello, Try to adjust the voltage potentiometer to increase the voltage
@scorebetter37095 ай бұрын
@@Electronic_For_You I tried but Egs002 will show error whenever vfb voltage gets below 2.55v
@scorebetter37095 ай бұрын
@@Electronic_For_You I have given VFB signal externally around 2.65v I don't have feedback circuit. But I gave it 2.65v using 10k potentiometer .
@scorebetter37095 ай бұрын
@@Electronic_For_You brother why transformer primary voltage gets dropped from 8.41v to 4 volt As I connect it to my egs002 vs1 and vs2
@Electronic_For_You5 ай бұрын
I think that means your transformer cannot generate high enough voltage, please try using a different transformer !
@ОбитательЗемли-и8щ5 ай бұрын
220 from the network got into the socket of the 8000 watt inverter, how can you help?
@Electronic_For_You5 ай бұрын
Hello I do not understand the question! Do you mean how to connect mains to inverter output like UPS?
@mikepaul2831Ай бұрын
@@ОбитательЗемли-и8щ Аll mosfets were destroyed and are to be replaced as well as dozen of other components on the plate. After being repaired the damaged invertor will continue to work as nothing happened.
@faisalusmani90638 ай бұрын
can you share transformer secondary coil voltage 7 or 12 please sir tell us
@Electronic_For_You8 ай бұрын
12V
@hichamtassi17533 ай бұрын
Dear Sir, what is the purpose of the choke ? thanks
@Electronic_For_You3 ай бұрын
Choke is for to remove any noise or spikes , ( it's not necessary you can use it without choke )
@alphagaming03362 ай бұрын
3:33 What is the purpose of diode used in all mosfets of gate
@Electronic_For_You2 ай бұрын
Fast discharge all MOSFETs
@The11kvexperts4 ай бұрын
pls tell the value of choke inductor filter used and its connection with capacitor
@Electronic_For_You4 ай бұрын
It's from old crt TV , I haven't measured value
@Mr.Pakistanihacker44594 ай бұрын
Can i use 1n4007 diode i don't have 1n4148
@Electronic_For_You4 ай бұрын
You have to use a fast diode
@Mr.Pakistanihacker44594 ай бұрын
@@Electronic_For_You Thankss
@basitronics61523 ай бұрын
Can you give me the list, so i can buy these parts. Thanks
@Electronic_For_You3 ай бұрын
You can collect lists from schematic
@pp-ch3jq3 ай бұрын
I have followed the schematic and built one. I got 54 V ac out of the 12 to 220 V transformer. All of you building these egs002 inverter and shpwing that it gave 220Vac from a 12 to 220v transformer there is something you are not telling us. I built another one from a youtuber who used just 2 mosfets on pin 3 and 6 to a center tapped 12 0 12 transformer and that one gave me abt 200vac and lighted my 100W bulb but it was a square wave.
@Electronic_For_You3 ай бұрын
You have to use a 7V Transformer so the total input voltage will be 12V To 14V Maximum! If you built everything correctly it will work 1000%
@pp-ch3jq3 ай бұрын
Thanks for the response. I want to remove the transformer out of the picture. Please what voltage am I expected to get from the inverter output before going into the transformer and will this voltage be sinusoidal ?
@Electronic_For_You3 ай бұрын
You will get around 7-8V Without a transformer, and it will be mixture of SineWave and square wave without filtering , you can try putting a 2uf capacitor for filtering in theory it should make output SineWave without any transformer before powering the circuit use a low current Supply like 12V 2-3A so if you made any mistake on connection your circuit doesn't blow up , because inverter based on EGS002 are very sensitive!
@pp-ch3jq3 ай бұрын
Thanks a lot. After putting a 2.2 uf at the output from the mosfets I got 9V. So I'm on course. I will work on this to get a smooth sine wave before hooking it up to a transformer. I intend to use 24V battery with a 12V transformer instead of winding a 6 0 220 transformer.
@Electronic_For_You3 ай бұрын
Good to hear that it works, But it should be SineWave after the transformer according to the datasheet of the module! Goodluck try doing some experiments ✌️
@Shivamyadav-xz8ri9 ай бұрын
This invertare charging feature add please
@Electronic_For_You9 ай бұрын
Ok i will try something about it
@salmanwe-ml5tk8 ай бұрын
what is the stenby current?
@Electronic_For_You8 ай бұрын
1.2A
@salmanwe-ml5tk8 ай бұрын
Does it seem like a waste of battery?
@Electronic_For_You8 ай бұрын
Yeah, 15W Of Power waste!
@salmanwe-ml5tk8 ай бұрын
Thank you sir..Can a 0.1 ohm resistor be jammed?
@Electronic_For_You8 ай бұрын
0.1 ohm will heat up hard Use 0.01 ohm 5W
@sepidehshabani-zd4lh3 ай бұрын
please give us information about filter choke inductor.
@Electronic_For_You3 ай бұрын
It's from an old CRT TV , not necessary
@sepidehshabani-zd4lh3 ай бұрын
@@Electronic_For_You it means that transformer output connected to rectifier directly?
@Electronic_For_You3 ай бұрын
As it shown on circuit diagram
@Electronic-1017 ай бұрын
Як намотати трансформатор ? 🇺🇦
@Electronic_For_You7 ай бұрын
You can use UPS Transformer 😊👍🏻
@Electronic-1017 ай бұрын
@@Electronic_For_You Добре 👍 Дякую.
@Electronic_For_You7 ай бұрын
Welcome 😊
@AnalysisAsia9 ай бұрын
Good
@Electronic_For_You9 ай бұрын
Thanks
@scorebetter37095 ай бұрын
Bhai tumne previous comment delete kyun kiya
@Electronic_For_You5 ай бұрын
Sorry I cannot translate your comment can you talk in english, thanks
@Mr.Pakistanihacker44594 ай бұрын
St4148 zener short why?
@Electronic_For_You4 ай бұрын
4148 is a fast diode , not zener
@MTKGENIUS5 ай бұрын
Give link where I can buy that small osciloscope
@Electronic_For_You5 ай бұрын
AliExpress.com eBay.com Daraz.com
@Shivamyadav-xz8ri9 ай бұрын
Please make the invertare egs002 and used farite transformer
@Electronic_For_You9 ай бұрын
Ok maybe in future
@MS-qd6vs5 ай бұрын
Good work,i buy 5 of Chinese sine waves oscillator i have burnt 4.
@Electronic_For_You5 ай бұрын
Yeah, They blow Up very Easily,
@juancarlosariascastillo46593 ай бұрын
Esta excelente el video pero deberias hacer un diagrama
@Electronic_For_You3 ай бұрын
There is
@anandakrishnanVU3CPF5 ай бұрын
White sticky thing name is Thermal paste or Heatsink paste
@Electronic_For_You5 ай бұрын
I know
@younchaounjankouo97364 ай бұрын
With the assembly diagram it's even better
@Electronic_For_You4 ай бұрын
I have only circuit diagram
@younchaounjankouo97364 ай бұрын
For pure sinusoidal?
@Electronic_For_You4 ай бұрын
Yes
@younchaounjankouo97364 ай бұрын
Ok please can I have your WhatsApp via Gmail? Please
@Mr.Pakistanihacker44594 ай бұрын
Bhai zener short hogaye chaaro
@Electronic_For_You4 ай бұрын
Because of the resistor used in parallel
@SlowAudio5765 ай бұрын
Really 300W
@Electronic_For_You5 ай бұрын
Yes, But you have to use a (Real) 400W Transformer to get (300W)
@SlowAudio5765 ай бұрын
@@Electronic_For_You Sir i want to tell u something plz😇
@Electronic_For_You5 ай бұрын
Yes
@SlowAudio5765 ай бұрын
@@Electronic_For_You Sir, Please Make a Video on this topic : How to build own inverter In this video You Will Teach us (Give Idea) How to make Own inverter Circuit. There are some formulas for winding coil in transformer for inverter. Like that we need the idea or formula for create Own inverter motherboard like mosfet section, pwm section, feedback section, filter section etc.... I never believe other KZbinrs. Their titles and fake thumbnails claim that The inverter they make in their video will be 500w,1000w etc, but they test an led of very low watt, an fan of low watt. 🤣 Please start a series or make a single (long) video on this subject plzz. 🙏 There is almost no videos on KZbin on this topic. 😔 If you make videos on this topic you will get content and value, And we get Best And genuine knowledge. ❤🥰