How to make a small and powerful induction soldering iron

[@alaninbliss]

A regular cheap soldering Iron uses "induction" to heat the soldering Iron tip. This one primarily heats the paperclip through high current via a transformer. Induction happens in the coils of the transformer, but the soldering iron tip (i.e. the paper clip) heats not via induction but through high current. None the less, impressive build. I enjoyed watching it.

[@ernieschatz3783]

That's what I was about to say as well. Induction happens in the circuit prior to the tip, but the tip heats because of resistance to the current produced by the circuit. The soldering is done via thermal transfer and not induction, which induces current via magnetic flux lines expanding and collapsing at frequencies that rapidly move the molecules of ferrous metals. So it's a big stretch to call it an induction soldering iron, but a cool project nonetheless.

[@BCDTech]

Induction soldering iron can induce heavy current in shorted inductors inside circuit, so be careful using this type of irons. Rest the iron is very good...

[@ientu1022]

BCD Technology kzbin.info/www/bejne/bZ61Z51ua5mVoNk

[@rasoolkeuusoolfatimakekhet72]

Gaand maar ek jhatke me agar kahin circuit chuaa gya to

[@ronidaffan5904]

Thank you so much for this video! I think only a few viewers understand how ingenious this design really is. Your design is much more sophisticated than it looks like.

[@mantisgaming]

Roni Daffan well, he’s faked some stuff in the past, but he seems to have stopped doing that.

[@foureyedchick]

What is NICE is that he used a bolt with 2 nuts as a secondary "winding" on the transformer! That's what's great about high frequency circuits. You can use small transformers with very few turns on them.

[@theanw00l0w2]

Good tehcing and can let pepleh understand perfaecly well.wonderfool😀😀😀😀

[@Bk99JzM]

Witam i pozdrawiam!!Super wykonana lutownica,bardzo dobry pomysl,bedzie pomocna przy lutowaniu plytek elektronicznych,dobry pokaz filmu ,tak trzymac!!

[@marinpetrescu6891]

Wow ce tare ,o fata care îi place electronica frumoase mâini ❤️❤️❤️😘

[@naguisamai3481]

this video only shows how you build it, but it does not teach how to build it, you do not give a list of materials or values of the resistances or put a diagram etc :C

[@tookitogo]

naguisa mai Schematic at 1:40.

[@memelocater]

he

[@ientu1022]

naguisa mai kzbin.info/www/bejne/bZ61Z51ua5mVoNk

[@menduelgabil8199]

yes

[@ientu1022]

kzbin.info/www/bejne/a2qYp5mvm9F4b7s

[@suneolsson9815]

Wonderful solder iron,,, perfekt to solder chassie then you nead to heat up quickly and lot of power,,,, normal solder iron cant do it, Thanks for this wideo,,, i shell build one,,,

[@DrHarryT]

That is not induction heating. That is a high current step down transformer heating a wire. (paperclip) Using Gates to turn the 12v DC into AC...How well do the Gates handle the load of driving the big 2mm wire? Apparent there would have to be a "Duty Cycle" (1min on, 5min off ???)

[@superpesbarbos]

Yes, exactly! And the screw is 1 turn coil! The main problem that Fuco's current is much higher.

[@deBobsico]

That's what I thought... Sad that induction is mentioned as a buzzword in the title, very misleading, not educational, etc.

[@davemwangi05]

your comment was good until you mentioned gates and duty cycle.

[@ocayaro]

You are right. Induction heating is contactless, but there are no "gates" here.

[@jessstuart7495]

Yeah, I was a little disappointed by the video. I was thinking it was a small induction heater used to heat-up and solder small hardware (standoffs, bushings, etc).

[@mazherdubai3898]

Very Excellent ❤️❤️❤️😊😊😊

[@electronicsNmore]

That soldering iron needs a good cleaning and tinning.

[@CursoPortugues]

He would not need it all if he knew how to use and clean his soldering iron.

[@ientu1022]

kzbin.info/www/bejne/a2qYp5mvm9F4b7s

[@joshhayl7459]

@@CursoPortugues, 🔵 Is it really that hard for some people to keep their soldering-tip cleaned & tinned?

[@joshhayl7459]

🔵 You need at least a seven or eight hundred degree tip for that soldering iron for the kind of work you're doing here, and the tip you got ain't workin' so good cuz it needs tinning BADLY!! I see a bunch of cold-stressed-joints that are mechanically weak.

[@creativeplus2315]

Very good , I want try this too

[@ientu1022]

Creative Plus kzbin.info/www/bejne/bZ61Z51ua5mVoNk

[@gigabytecddvd]

I loved this project!!!!! I will do

[@terranovarain6570]

Now you need to use that one to soldier up another one with all the cold soldier joints in it lol 🙌 really cool though

[@e.solano6308]

Great video. VERY informative.... Only one complaint not against video or instructor but at @youtube ..plz explain why in the #@$& was there 5 freaking ads WHILE WATCHING THE VIDEO.. along with before and after but DURING ... ALMOST made me lose interest 2 ads were close to 30secs.😠 SMH. Other than that.👍👍 Thanks for the diy project :)

[@minhbui-wh5ig]

@E Solano, the ads come from KZbin not from the author of this video. A simple solution to this annoyance is to install the AD BLOCKER extension to Firefox then you will have ads free from KZbin or whatever web page you visit. Open Firefox, go to "preferences" then "extensions & Themes" and type "AD-BLOCKER" on "find on preferences" tab, click "AD-BLOCKER" then click "+ Add to Firefox". Close Firefox and open it again, now your computer is free from all ads. Similar procedure work on Safari, Edge program too, hope it help.

[@miguelangelrodriguez667]

Te puedo poner KZbin sin anuncios si quieres Solo contactame

[@enriqueescalante3471]

Jjjjjjjjjj

[@ashishsahu6403]

Love from india🇮🇳🇮🇳🇮🇳🇮🇳 to 🇱🇷🇱🇷🇱🇷

[@real4487]

Finally you made something good

[@ElectroeliasElCanaltuyo]

Yes is true jajajaja

[@valveman12]

Manpreet Singh No he didn't make anything good. This is supposed to be an induction soldering iron. There is no induction, It's Bullshit like all his other videos. Money is more important than integrity.

[@noobsgaming9528]

How To Make Boom Box at home kzbin.info/www/bejne/lWWWiHSrr8Stoqc

[@geirmyklebust]

unfortunately ..... its too powerful, useless.

[@brycewellington5529]

Yeah but you need a soldering iron..lol

[@ВладимирСимон-щ2р]

Good device, Hello from Russia.

[@MacStrange]

Idea utile e interessante 🧤

[@diyelectronics5537]

ho capito cosa hai detto, but you should write in english, as you are on an english channel

[@gabrieljuarez6721]

QUITEN ESA MUSICA ESTUPIDA

[@Luk3D]

Porco dio

[@rafaelorion120]

tu trabajo es excelente , no habia visto un cautin asi y tope con tu video por casualidad te fecilito te doy 100

[@darwensky5386]

Great! Congrat

[@bollywoodblockbuster6482]

kzbin.info/www/bejne/nXWceqCnqq5letE

[@deepzoned]

how to make soldering iron using soldering iron :D

[@saifuladliyusof334]

😂😂😂😂

[@danielkyorchev6518]

Yeah xD

[@rhelterdoon6328]

I think it 😂😂😂

[@taiga-yt225]

I was gonna say that lol 🤣🤣🤣

[@scrumpyhunter8561]

yeh with shitty music and no real guidance on what or why it is being done...

[@tktao9122]

Đệp quá đi mất 😃😃🌺🌻🌹🌸🌷

[@7MinutesCreative]

interesting video hi everyones have a good day

[@danfishermen5362]

Thanks you to

[@davemwangi05]

7 minutes, i see your channel is awesome

[@7MinutesCreative]

Divad Ignawm thankyou so much 👍👍👍👍

[@MobileDoctorMIJANUR]

Mind blowing really thanks

[@migoffmig]

Для такого паяльника блок питания не хилый должен быть.... Как по мне, обычный паяльник лучше.

[@ОлегНосаль-щ4й]

Автомобильная батарея само то. Как раз на полчаса попаять. Или зарядка 12 вольт 5 Ампер и выше. Тоже потянет нечего делать.

[@Djoni139]

@migoff mig у меня такой паяльник работает от БП 12В 2А, в начале, когда жало холодное, кушает около 1,5А, потом по мере разогрева жала ток понижается. Мосфеты использовал 60N03 со старой материнской платы, очень слабо греются даже без радиаторов. Кольцо взял зеленое от фильтра питания компьютерного БП на 400Вт, первичка 16 витков проводом 1,5мм с отводом от середины, вторичка - один виток из 8 жил проводом 0,8мм.

[@ib1713]

@@Djoni139 спасибо, за ориентир

[@avsam1992]

Good job. very useful

[@LaszloToth55]

You can use a cord with several wires instead of a 2mm cord. The high-frequency current is not moving inside the wire, but on the wire surface.

[@FareedClarity]

Wow amazing, nice project👍👍👍

[@gugus.5536]

how to make a soldering iron.Materials: other soldering iron

[@Rakesh-hk7bc]

राकेश मेघवाल

[@sagarghatti]

Material list realted video upload next time with detail. Now they are just showing soldiering iron hack

[@sagarghatti]

Material list realted video upload next time with detail. Now they are just showing soldiering iron hack

[@ientu1022]

kzbin.info/www/bejne/a2qYp5mvm9F4b7s

[@houssamadenaboudaile9385]

رائع منتهى الدقه والتقنيه العاليه وروح الإبداع المفيد والعالي

[@ky6ok]

Сonversion efficiency 30-40%. The rest goes to the air heating))

[@phuonghungofficial7536]

Perfect, I want to buy it.

[@phuonghungofficial7536]

Use battery 12 volt?

[@greywolf8931]

Don't it end up with a load of dry joints when you don't use flux ?

[@bhupendradesai3402]

U r intelligent in making jenreter please make small jenreter for fan as power gone often please try.thanks all your item usedfyll n nice easy also.

[@raffyturc]

Judging from the video its a zvs flyback circuit in buck mode. And the pb sw will die shortly.

[@PafiTheOne]

Royer oscillator. And the switch deals with only the bias voltage of the MOSFETs.

[@davemwangi05]

lies. you don't know what you're talkin about

[@PafiTheOne]

@@davemwangi05 who did you respond to? And are you aware of your self-contradiction? Lie must be conscious.

[@lynxat0mic948]

PadiTheOne yeah lol

[@pesachn]

...will die shortly. You"re wrong.This circuit and similar are operating almost w/out power losses due being zvs flyback,high switch freq and low Ron MOSFETs. There is a video from a russian amateur,where he demonstrates similar iron he exploitng intensively for 20+ years and only once he required to replace the Fets.

[@johnconrad5487]

good idea!!! you could have put many more turns of thinner wire on the core.

[@ientu1022]

John Conrad kzbin.info/www/bejne/bZ61Z51ua5mVoNk

[@edifierbass7821]

Actually it's an inverter not inductive 12vdc to Ac in higher voltage output, not practical Use glow plugs -direct dc 4amps up or use a trafo - 3amps up then remove secondary winding replace it with a huge gauge #10 wire -3turns put filament thin wire on two leads and finish instant soldering gun

[@norapadillaoyervides4202]

excelente asta aorita de 100 tutoriales k e visto el mejor idea felicidades y grasias por sus enseñansas saludos desde monterrey nl mexico

[@frederickdino230]

I imagine how does the other soldering iron feel while making the thing that will replace him💔

[@ahmdabdallah5811]

What Is Islam? Islam is not just another religion. It is the same message preached by Moses, Jesus and Abraham. Islam literally means ‘submission to God’ and it teaches us to have a direct relationship with God. It reminds us that since God created us, no one should be worshipped except God alone. It also teaches that God is nothing like a human being or like anything that we can imagine. The concept of God is summarized in the Quran as: { “Say, He is God, the One. God, the Absolute. He does not give birth, nor was He born, and there is nothing like Him.”} (Quran 112:1-4) Becoming a Muslim is not turning your back to Jesus. Rather it’s going back to the original teachings of Jesus and obeying him

[@ImKevan]

Cool video, quick tip though, using some rough sand paper is a little safer and in some cases an easier way of removing the non conductive coating around copper wires, I've slipped with those utility knives doing the same thing before, it ain't fun, be safe!

[@SilviaFerrari68]

what are you using?

[@ientu1022]

Silvia Ferrari kzbin.info/www/bejne/bZ61Z51ua5mVoNk

[@РустемКутушев-ъ6у]

Прикольно . Компактная схемка :)

[@ЕвгенийЕрмоленко-й6п]

Используйте при пайке дополнительный флюс. У вас низкое качество пайки. В рабочей части нагревательного элемента необходимо уменьшить сечение, чтобы увеличилось электрическое сопротивление для концентрации нагрева.

[@ШамильНухаевто74ко8я]

Он бля целый паяльник запаял и ты его учишь как детей делать.

[@olexyvelychko7527]

@@ШамильНухаевто74ко8я, ну так ведь правда, кто действительно умеет паять, по видео сразу поймет, что автор не понимает процесса пайки, хоть кое как паять получается. Состояние жала еще одно тому подтверждение.

[@ДенисИванов-щ1ч]

#издец диванные эксперты))...на каждую мелочь ведь тыкать будете...Причем тут пайка,он лишь показал работоспособность....А паяльник сделан компактно,добротно👍

[@hassan-aljarjri]

More wonderful...Well done

[@zephirawt4997]

The iron core of screw must have large hysteresis loses...

[@mantisgaming]

Zephir AWT no, he used the screw as a conductor. The toroidal core is the core of the inductor.

[@ientu1022]

kzbin.info/www/bejne/a2qYp5mvm9F4b7s

[@DaniDani-nu7ts]

Realy Realy.....a serious channel

[@hansotimunda]

Beautiful construction........... Finesse just as fine as 'her' (?) well manicured fingers........!

[@magisterlino6386]

excelente proyecto pero me gustaría mas específicos en los componentes gracias

[@axelcampos5354]

Que tal lo lograste hacer. Yo no encuentro en español para hacer uno.

[@rogelioliscano5970]

@@axelcampos5354 yo lo hice es muy fácil solo consta de 2 mosfet 4 resistencias 2 diodos un bobina primaria y segundaría y un capacitor de poliester me costo al principio pero ya e echo varias pistolas de ese tipo...

[@axelcampos5354]

@@rogelioliscano5970 has un vídeo. Nos serviría de mucho.

[@rogelioliscano5970]

@@axelcampos5354 me gustaria pero no cuento con una camara amigo ni tengo canal en yutu.

[@Samvsungok]

Золотые руки!

[@adnanfnaish8489]

The elec.parts never been explained and where to get them otherwise it's a very informative video

[@trewmika1869]

Also the transformer made of toroid looks weird. There are not fields going through the screw, I suppose. If you can explain pls tell me how it works.

[@ientu1022]

kzbin.info/www/bejne/a2qYp5mvm9F4b7s

[@mukeshsenwar7151]

Nice, very good,

[@NadaOfConsequence]

When the music repeats I died

[@ДелікатнаНаталія]

Ллддлддллдббл

[@8287David]

L

[@ientu1022]

kzbin.info/www/bejne/a2qYp5mvm9F4b7s

[@marcosboto7342]

Me gusto mucho 👍👏👏👏

[@rodrigodiego7836]

Hey Thanks by the video! For 24v how many turns I need to do for the inductors?

[@bollywoodblockbuster6482]

kzbin.info/www/bejne/nXWceqCnqq5letE

[@bollywoodblockbuster6482]

Watch and subscribe please

[@aturntech3685]

Good i am sri lanaka

[@sandichhuu]

Thank you. I have following you to make soldering. My circuit info : Primary : 12-14 turn. Secondary : 1 turn. Capacitor : 47nF. Small inductor : 470uH. R : 470 Ohm + 10k Ohm. Diode : 1N4007 I wait more than 30 secons that make heat enought to soldering. Why primary coil so hot ? And how to fix ?

[@fabriziobrutti1205]

Turn it on and tell me if became hot first the coil or the ferrite core or the coil an then I ll'try to explain you how to fix the priblem Ps sorry if my maybe my English isn't correct but I'm Italian

[@nobabpurelectricbazar4795]

how I can get it

[@sandhuprince3956]

Who When Why Where Nobody cares

[@famgonzales1091]

Try voltage check... Maybe less coil turn

[@apsysspace6764]

You need 1/2 turn

[@ilhammuslimov2598]

Super 😊👍

[@АлександрЧурсин-я2т]

Кто из России??

[@Андрей-у1у6ч]

нет никто

[@blue_bird3415]

только Украинци

[@АлексейНимерчук]

Украинцы из Молдовы из русской Школы

[@ВалентинНікіфоров-н5о]

Не я

[@davemwangi05]

damn russians, speak in english men

[@electronic7979]

Excellent project 👍

[@Hararion]

Interesting design, please Share the circuit with the coils details, also please give information about the material used as a tip, want to make a portable soldering iron with a 12 volts battery to repair things in a model flight camp, is perfect for this use!

[@fss1704]

hey, i find the easiest way to make an induction soldering iron is to make a heating zvs with a soldering iron tip inside, or you can use an halogen lamp of 55w with a cover from an old broken soldering iron

[@fss1704]

my best soldering iron was this zvs i made.

[@noobsgaming9528]

How To Make Boom Box at home kzbin.info/www/bejne/lWWWiHSrr8Stoqc

[@JodBronson]

+ACT 2 DIY - We don't want to make a Boom Box !!! Buy it at Dollar Store for $1.00 LMFAO !!!

[@nolansykinsley3734]

I have seen several fairly capable USB powered soldering irons that you can carry a power pack for in your pocket, I would probably opt for one of those rather than trying to build my own. I believe BigClivedotcom and EEVBlog have both done videos on them.

[@SPTECH-dh5rg]

You are great brother..

[@АлександрГанев-г6н]

Я бы ещё регулятор добавил, и корпус.А идея хорошая.

[@miglezf]

Yo voy a destacar la delicadeza y prolijidad para trabajar. Hermosas manos. Felicitaciones mujer, me dio mucho gusto ver el video. Los voy a seguir. Gracias! Además, todo muy útil, práctico y claro

[@HARRYKENNETHful]

Interesante puede ser, pero es solo para personas que entienden de electricidad. Uno no conoce los componentes. No es para todo público. Lástima.

[@hevycont9451]

Es cierto ni siquiera pone Qué tipo de componentes ocupa ni los valores de cada uno :(

[@davidfernandezmego9143]

@@hevycont9451 usa los mismos componentes que este video kzbin.info/www/bejne/nJOXYXisl9p7hpY Solo que lo ha adaptado a este proyecto. Saludos (Peru)

[@MyHernan666]

Si pone amigo los. Componentes y el diagrama fíjate en el minuto 11:51 allí sale como armarlo saludos

[@rogelioliscano5970]

@@MyHernan666 yo lo hice es muy fácil solo consta de 2 mosfet 4 resistencias 2 diodos un bobina primaria y segundaría y un capacitor de poliester me costo al principio pero ya e echo varias pistolas de ese tipo...

[@echipajulsperanta1854]

yes! Induction soldering iron can induce heavy current in shorted inductors inside circuit, so be careful using this type of irons

[@Evgeny2681]

обычный паяльник секунда, схема распостранялась в журнале юный техник!

[@СерёгаГаврилов-р2п]

А схему можешь нормально скинуть а то ничего не понятно размазона

[@ientu1022]

Евгений Рябчунов kzbin.info/www/bejne/bZ61Z51ua5mVoNk

[@Ярослав7000]

главное, то что очень удобный и легкий)))

[@ДмитрийМалхазов]

Ага, ещё бы показала как всё паять, а не просто схему)))

[@hayrettinavci62]

hi. can you give me information on L3 coil also how many 22 nf capasitor's voltage? thanks.

[@ATdiy]

Thank you , I used 8mm screw as L3 = 1turn and 22nf/ 250v capacitor

[@hayrettinavci62]

thanks.

[@davemwangi05]

American Tech. One turn for the current limiting choke really? I'm puzzled.

[@hayrettinavci62]

I understood that L3=8 turn for 1 mm but L3=16 turn it's seems at the video. which one is correct?

[@AhmedSayed-oo4uw]

@@hayrettinavci62 how l3 is 1 turn

[@nillchen]

beautiful, technically but also designwise with the toroid's mechanical function

[@bojangles2492]

You needed a soldering iron to make your soldering iron, how ironic..

[@subhodhara5935]

You needed your mother to bring you on earth , how ironic... 😂🤣

[@хххх-з8м]

Bravo! you leider! Like !👍👍👍👍👍👍👍🏼👍🏼👍🏼👍🏼👍🏼

[@laxmansurnar8425]

Used Material details upload please

[@rezamesri1678]

Very nice but we can make it by a small 240V or 110 V to 6V transformer using 5 turn wire in secondary. Then you don't need any circuit.

[@muhammadbhama]

Using soldering iron to make soldiering iron

[@daviddelatorreperez4]

Que lo solde con el ass ?? O con que los soldarias tu ??

[@BrangkatBossOfficial]

Wow its smart idea, nice tech..keep doin it brother..

[@djtopherau]

this is not an induction iron. clickbait

[@johnconrad5487]

actually it is. he made a transformer and used the thin tip as the heater. it works exactly line the induction irons that you buy. they use a transformer with a 1 turn secondary for the soldering tip

[@LaszloToth55]

It is very useful in car when you need to do some reparing.

[@ientu1022]

Laszlo Toth kzbin.info/www/bejne/bZ61Z51ua5mVoNk

[@daraa151]

Watching this video is rather painful

[@shaiyachennelhoangliem3848]

rất hay (việt nam).verygood!

[@7MinutesCreative]

ok ha ha

[@cungxemnao5311]

Hay gì không hoạt động được

[@bietaiaibiet385]

If you want to hide the profession you can not share ... I feel angry when watching this video

[@ientu1022]

Biết ai ? Ai biết ? kzbin.info/www/bejne/bZ61Z51ua5mVoNk

[@dadamw6337]

Чтобы сделать паяльник, нужно использовать паяльник. Интересно)

[@eaglee-sports5427]

What is the transistor you have used

[@ATdiy]

I used mosfet IRFZ44N . For more information, Please see in the circuit diagram in this video thank you.

[@eaglee-sports5427]

@@ATdiy thank you vary much

[@gazaziho]

@@ATdiy also irf630 will work

[@mishame156]

I would advice a small limit switch instead of a button. It is realy comfortable.

[@МихаилГнетеев]

ААААААААА! Почему без канифоли! Без неё припой плохо садится! БЕСИТ...

[@mishame156]

У него пруток с флюсом, всё правильно делает и всё нормально садится.

[@МихаилГнетеев]

Значит ты не видел как нормально садится

[@SergiyRadonezhski]

@@mishame156 чел, с качественной пайкой с обильным флюсом припой становится блестящим как зеркало и как вода обвалакивает все места соединения без катышков и пузырьков. На такое качество любо дорого смотреть. То что показано в ролике это жесть. Внутри проволоки припоя флюса ничтожно мало. Нужно все равно добавлять. И да, флюса много не бывает! И да, с качественной пайкой сопротивление соединения в разы ниже некачественного. А это в схемах очень важно.

[@servis9693]

@@МихаилГнетеев 😄😄😄

[@todaysunday4710]

It's easy, but so cool!

[@ИгрьРадченко]

Хрень какая-то. На первичке токи такие будут что те транзисторы сгорят моментально. Темболее с таким охлаждением

[@imkkyiv]

60W=12V*5A і це якщо для постійного струму, для високочастотного режиму порядок струмів не більше

[@andyshevchenko5616]

А какой он провод на дроссель поставил. :-)

[@ArdyActubOfficial]

That was great I love it..

[@s.b.bambhaniya4467]

MST

[@Alex-fh2th]

@@imkkyiv Все выдержит... у таких транзисторов сопротивление включенного ключа тысячные доли ома и рассеиваемая на них мощность получается мизерной...

[@nailsaggitarius4212]

American Iron. Very nice!

[@bdf2718]

All that and it produced some of the shittiest solder joints I've ever seen. What made it worse was that you were re-working existing joints, and it's *hard* to mess that up. A new joint to untinned components is easy to mess up with bad technique or bad tools, but messing up a joint that you're essentially reflowing is hard to do. Clever induction heater, but do *not* use it as a soldering iron. At one point the tip was glowing red. There's a reason good soldering irons are thermostatically controlled. It's because too high a temperature messes things up. Red heat is *far* too hot.

[@Hudsonkem]

if you notice he turn it on and off when doing so. the width of the wires isnt that big so it looses temperature very quickly...

[@bdf2718]

@@Hudsonkem The low thermal mass makes it worse, not better. A thermostatically-controlled iron also switches on and off but the thermal mass means the temperature stays within a small range. This piece of shit cycles between too fucking hot and too fucking cold. The result is a very crappy joint.

[@ib1713]

Хорошо придумал, надо индикатор и подсветку добавить

[@johnynevskiy4844]

Херня, нафига в паялнике столько электроники, обычный дроссель из дедовского телека и 3 витка вторички 5 мм. Готово!

[@Fedor-1313]

johny nevskiy дроссель будет тяжелее на много.

[@ientu1022]

johny nevskiy kzbin.info/www/bejne/bZ61Z51ua5mVoNk

[@Ploplemp]

Nice. Now learn how to use it the right way.

[@valveman12]

American Tech Wow ASIAN TECH, you put a video about building an induction soldering iron. WHERE IS IT? All you built is a soldering iron with no induction. So how about making videos that are not bullshit from now on. This video without a schematic is lacking and not induction. Do you even know what Induction is??? Show some integrity.

[@Timeboxing-k2w]

Good!

[@hungtrieudang7358]

Hay lam ban oi 😘😘😘

[@alexeyk4591]

При помощи одной размазывалки припоя получилась новая размазывалка припоя :))))

[@iblesbosuok]

wow! fancy construction. I love it. cheers from Indonesia

[@bollywoodblockbuster6482]

kzbin.info/www/bejne/nXWceqCnqq5letE

[@jackmclane1826]

This is a conventional soldering iron powered by a high current transformer. Nice built, by the way! But it is not an induction soldering iron. The heat is not created by induction in a workpiece, but using the resistance heating in the paperclip wire.

[@bobemedox988]

Merci bien bon travail une fera soudée

[@wayansueno6720]

The video but the cat shows off knowledge but it is not stingy that all the series are opened. This video is like a useful TDK.