Thank you! yours videos are perfect! keep it up this way.
@KPeyanski8 ай бұрын
Thanks, will do!
@lucamarcio41102 жыл бұрын
Ciao Kiril, what about creating an aquarium control device that controls temperature, water level, pH value and LED lights all together? It would be great and your tutorial would have a tons of visualizations for sure! Think about it, please! Many thanks.
@KPeyanski2 жыл бұрын
Cool idea. I will think about it. Thanks for the comment
@botialoach12 жыл бұрын
Excellent, keep up the great work you are doing , I needed one for my fish tank , when you have time think about a temperature sensor for my fish tank also, many thanks
@KPeyanski2 жыл бұрын
Thanks, will do!
@taxy718 ай бұрын
yes please, im trying also project for my >Aquarium Ive got TDS sensor , Ph sensor (same as you have), and Temperatur sensor DS18b20. it would be really nice to have one video from you. I think a lots of ppl from Hassio do have Aquarium and they would be also happy. same sensors can be for pool in use. THANK YOU
@osr75 Жыл бұрын
Nice Video with good idea! I'm trying to do for a pool, the idea is to take an esp32, or similar, power with small solar panel with some small betteries and test PH, TEMP and ORP or clorine. All togheter insde in a floating Clorine device, with the solar panel on the top! with ESPHOME every 30 minuts ( for example) ESP32 with wakeup, send PH+TEMP+clorine level by WIFI to Home assistant, and go to deepsleep andother time for 30 minuts! In the mena time the minisolar panel will give power to the batteries to keep enough energy!
@JournaldeThomas2 жыл бұрын
It is really a good idea and I will try to do something similar. But I am wondering how to let the pH meter all the time. Perhaps on the top of the pump…
@KPeyanski2 жыл бұрын
Yes, top of the pump is not a bad idea. I may "steal" that from you ;)
@private2707 Жыл бұрын
Thanks for the great tutorial!! I was wondering if you went further and pickup a thermometer to read the solution's temperature. PH reading will vary according to the temperature.
@therevoman Жыл бұрын
can you do this and add the temperature sensor as well?
@kirkk26435 ай бұрын
Did anyone find the solution for temperature compensation?
@Tntdruid2 жыл бұрын
Very cool, I need to try that 👍
@KPeyanski2 жыл бұрын
Go for it! And let me know what happened.
@Hautakoskifi- Жыл бұрын
I got this to work! And also add Dallas temperature sensor. Using it with aquarium..
@Hautakoskifi- Жыл бұрын
Also making other one for my pool for next summer! I have just take first steps to home automation, esp so on. Thank you for making also good videos. Without good videos, it’s not kinda possible to start to make sensors so on. Good learning, step by step. 😁
@KPeyanski Жыл бұрын
Great to hear. I'm super happy that I was able to help. Don't forget to check my other DIY smart sensor videos. I have a whole playlist of them :) Enjoy!
@Robert-JanKempink Жыл бұрын
Nice! i would like also to see a video about ORP :) i think that would be a little bit harder but possible
@erwinmikkers87082 жыл бұрын
I've been wanting to build this for our pool. Would love to see a project including a chlorine sensor!
@KPeyanski2 жыл бұрын
Yes, That would be cool!
@clairerovic2 жыл бұрын
@@KPeyanski so cool
@rolschu1960 Жыл бұрын
yes chlorine and salinity sensor. Is there any possibility you could do that? Are there sensors on the market? Great videos!
@botialoach1 Жыл бұрын
Great work keep it up, can not wait to use my pH sensor in my fish tank but I have a problem after connecting everything together all I get on the display is squares or nothing depending on the position of the potensiometer of the display NO readable letters any help would be appreciated ?
@kirkk26435 ай бұрын
THANK YOU. Followed your example and it works as expected. However, I noticed that the pH value doesn't represent the reality when the pool water changes temperature. Can you please tell me how to fix that? Couldn't find anything about how to make temperature compensation.
@scottfinley89554 ай бұрын
Worked for me!
@KPeyanski4 ай бұрын
Well done! Congratulations and welcome to the club!
@nehajain29742 жыл бұрын
You make such great useful tutorials... please please please make a tutorial on how to connect and use multiple Bluetooth speakers with raspberrypi.... please I have been searching how to achieve this since so long. Please consider this humble request
@KPeyanski2 жыл бұрын
Thanks, I will think about it!
@joels76052 жыл бұрын
Excellent work, sir.
@KPeyanski2 жыл бұрын
Thank you very much!
@marconugnes61922 жыл бұрын
Great idea! Thank you! Do you think is it possible to have multiple sensors? Ph, temperature and chlorine? Marco
@KPeyanski2 жыл бұрын
Why not? I think it is doable...
@marconugnes6192 Жыл бұрын
One last question.. is it possible to do this project without a screen? For working with esp home it’s a must to have an i2c bus?
@JoaoGabriel-bk6pn2 жыл бұрын
Top!!!! This was what I was searching! Is it possible to make it without the screen? Thanks
@KPeyanski2 жыл бұрын
Yes, of course
@bobbymsq Жыл бұрын
Great work thanks for sharing, can you help with this cuiosity, what's the use for the 5k potentiometer?
@ИльяКаратаев Жыл бұрын
Hi there, thanks for your effort. I have a question: Do we need to remove the pH meter sensor from the water? For example, if I have a substance that I need to measure, should I periodically remove and clean the sensor?
@christian16032 жыл бұрын
Nice video, just what I needed ! For powering the ESP8266/ESP32 : I presume each micro USB cable with adapter of any phone or tablet may be used for this (are Amps important ?) ? Do you have a link in case I would like to buy one for this project ? Thanks !
@KPeyanski2 жыл бұрын
Yes, adapter is needed or any regular usb socket like the one from a laptop/desktop or other similar devices. Amps are not important.
@robertzioo6508 Жыл бұрын
Will it work without the screen? I want watch pH in Home Assistant only. Your videos are very useful. Thanks
@aaryanpour8 ай бұрын
Yep, if you monitor the Esp32 log of the device, effectively will do the same i.e. reading the voltage (Ph)
@xsiimonox5 ай бұрын
Hi i have a new version of the ph probe. the SEN0161-V2. There is no potentiometer to turn. how do i calibrate this one? can u help me plase?
@peripharel2 жыл бұрын
Worked perfectly! So next step is to control dosing pumps. Anyone have any examples?
@KPeyanski2 жыл бұрын
Great to hear! So you can use the #phowned hashtag as well, right? 😉
@peripharel2 жыл бұрын
#phowned
@511Burak7 ай бұрын
Hi friend have a question. Is it possible to combine PH Sensor and a temperatur sensor to showing on the same display? Actually have another esp32 board to shown water temp. Is it possible to measure on same esp32?
@Mimbultonia9 ай бұрын
Can’t get this to work 😢 it seems the voltage output from the ph sensor board is very narrow when I finally got it adjusted so it’s not maxed out. Do you think I have a poor board or is there something else I can try?
@TheAlexdj1971 Жыл бұрын
Thanks for the video. I have a question. The probe you use has a screwable cap, If I leave this probe in a fish tank full time, can I remove the cap and get instant readings?
@codahq Жыл бұрын
did you try this?
@onyiercan4 ай бұрын
what is the role of potentiometer 5k Ohm?
@Edu2pc Жыл бұрын
Can the sensor be left permanently submerged in water without seriously risking the life of the sensor or its calibration?
@nyx574 Жыл бұрын
I was able to it built, but I can't get a stable reading. It bounces all over the place.
@antoniomazabandes5419 Жыл бұрын
Hello Kiril: How would we do it if we had two sensors for the display on the i2c screen?
@botialoach1 Жыл бұрын
I get nothing on the screen of the ph sensor when stand alone probably I have a faulty pH-probe or board but how to test ?
@vvkarhu14778 ай бұрын
Hi, how did you put the sensor in water. Can the probe be fully submerged in water so that only the cable comes out from the water? Thanks!
@KPeyanski8 ай бұрын
yes, you can do that
@vvkarhu14778 ай бұрын
@@KPeyanski thanks!
@fred7flinstone2 жыл бұрын
#phowned, although I find the values bounce around so much I doubt it's going to be that useful. I'm finding it pretty difficult to calibrate as well.
@KPeyanski2 жыл бұрын
Congrats, once you calibrate is the values still bouncing?
@Mimbultonia10 ай бұрын
I find the dh1 mini is a bit power limited. I already have a dh1 mini running a temperature sensor and when I added a float switch the temperature sensor stopped and I think this was due to power available - do you think it would also run a pH sensor or would it need its own dh1 mini? I’m a bit limited on power sockets and would prefer to run just the one dh1 mini if possible.
@przemysawkruzoek21304 ай бұрын
#phowned Thanks for sharing this
@KPeyanski4 ай бұрын
Enjoy and congratulations
@ElvisM19794 ай бұрын
how did you install the sensor in the pool? It is fixed or no?
@KPeyanski4 ай бұрын
fixed, but because my pool is seasonal (I mean I put it in one big box during the winter) the sensor is also seasonal :)
@blake6324 ай бұрын
Hello, when I adjust the potentiometer, the pH value changes, but when I turn the screws on the circuit, it changes very low and I put it in water, it measures the same, I put it in lemon juice, it measures the same, can you please help?
@blake6324 ай бұрын
I have ESP8266 NodemCu V3
@bencoleman423 ай бұрын
#phowned. Thank you
@KPeyanski3 ай бұрын
Welcome to the club, and check my other DIY video tutorials that I have
@Fluless Жыл бұрын
#phowned. for some reason esphome doesnt work on rpi but the esp webinterface does. thanks for the great tutorial
@KPeyanski Жыл бұрын
Congratulations and welcome to the club :) Enjoy your DIY sensor!
@woshitomtom Жыл бұрын
Hi, do you think it’s possible to use zigbee instead of wifi?
@KPeyanski Жыл бұрын
not sure about that
@511Burak7 ай бұрын
#phowned. Thank you
@KPeyanski7 ай бұрын
Congratulations and welcome to the club! Enjoy!
@sleepessence75662 жыл бұрын
I have built this following it to the letter and triple checked all cables etc. I have two issues 1) there is no display (it staes in the log communication failed) and also the sensor is stuck on 21.57 - even though I have tried adjusting the pots. Finally I connected the main 5k pot but you did not mention what to do with it. Any help would be appreciated
@KPeyanski2 жыл бұрын
for the display check the logs during the boot very carefully it is possible your display to have different address. You can also try to remove the address from the code completely as this will try the default address. The 5K pot should be connected and you can use it along with the adjustment knobs on the ph Sensor
@sleepessence75662 жыл бұрын
@@KPeyanski Thanks for the reply. I have checked the logs as carefully as I can but all it states is that the connection to the display failed. I have tried removing the address completely but no avaiul. Is there any way you can direct me as to what to look for in the log. Much appreciated - I really want to say #phowned!
@Fluless Жыл бұрын
Has someone tried using this setup with a tds meter?
@jjvelar2 жыл бұрын
Does not the reading oscillate a lot? A median of just 7 values is not enough for my setup
@KPeyanski2 жыл бұрын
They are. But isn't it normal when you add lemon to the water or you put the sensor in milk? I saw the sensor to reach 22PH so that means higher median.
@jjvelar2 жыл бұрын
@@KPeyanski it oscillates submerged in the same liquid. By the way, maximum pH is 14 so reaching 22 looks wrong to me. Calibration issue?
@sjaakhijmering49512 жыл бұрын
I am doing exactly the same with a salt pool but then the PH reading is way lower than it actually is... I calibrated the sensor with calibration fluid 4.01 and 7.01.. I am now back to doing it manual..:@? do you know what the problem may be? and yes a chlorine sensor would be awesome:)
@KPeyanski2 жыл бұрын
OMG salt pool :) That is cool... Do you have waves as well? Unfortunately I don't know what could be the problem.
@sjaakhijmering49512 жыл бұрын
@@KPeyanski today I tried to mix salt into the Calibration fluids still no luck:( Will sent a mail to the supplier I think.. its a normal Intex salt system BTW so not huge pool of something;)
@peteturcan825 Жыл бұрын
#phowned 😁 Thank you !
@KPeyanski Жыл бұрын
Great work! Enjoy!
@peteturcan825 Жыл бұрын
Thank you for your great work. Now will try to implement a temperature sensor
@nigelholland242 жыл бұрын
made mine but lcd stuck on -3.25 very acidic ,adjusting the pots dont help
@KPeyanski2 жыл бұрын
Strange, try adjusting the 5K Ohm potentiometer as well.
@nigelholland242 жыл бұрын
@@KPeyanski all working now must have been a loose wire.
@KPeyanski2 жыл бұрын
Great to hear. Don’t forget to leave a #phowned comment, but more importantly - enjoy!
@Tomasz-i6p Жыл бұрын
#phowned dzięki:)
@KPeyanski Жыл бұрын
Congratulations and welcome to the club. Check my other DIY Smart Sensor tutorials
@nigelholland242 жыл бұрын
#phowned
@KPeyanski2 жыл бұрын
That is better. Well done ✅
@PeterNordin2 жыл бұрын
Do you have the sensor in your pool all the time?
@KPeyanski2 жыл бұрын
No, not yet. My cable is too short and I have no place to mount the sensor steadily and safe. My pool is small and temporary (just for the season) and there is a lot of action in it from time to time with a lot of splashing, so I'm still wondering how to do that.
@farkasroman2 жыл бұрын
#phowned
@KPeyanski2 жыл бұрын
Wow, you are fast :) Good job Roman. Enjoy!
@aaryanpour8 ай бұрын
#phowned
@KPeyanski8 ай бұрын
Congratulations and welcome to the club! You can now try my other DIY smart sensors :)