how to make use Load Cell sensor with Arduino Uno

[@JulianReino]

I see that you connect the hx711 to the 5v pin on the Arduino uno and the LCD to the 5v pin as well. My arduino uno only has one 5v pin. How does this work?

[@passiontechklm]

@@JulianReino you can loop 5V from Arduino pin or give extra 5V will do.

[@normalbenedd8707]

​@@passiontechklmcan I use it on Arduino mega?

[@zohairdilawar116]

How do we trf this weight displayed to Google sheets

[@theallroundershow576]

Which type of jumper wire did you use???pls reply

[@passiontechklm]

Any types of jumper wire you can use ,I use here male to female 20cm jumper wire.The important is to transfer the data and power only.

[@kienleanh389]

Tks brother, it works but the weight in LCD is unstable and digits dont move when i put things on it

[@rar9119]

Does this sensor work with Raspberry pi microcontroller or is it only compatible with Arduino?

[@passiontechklm]

It's competitable with Raspberry too.

[@rar9119]

@@passiontechklm Thank you 🙏

[@madhumaytripathi4216]

zip file is not included in description

[@passiontechklm]

Please check in description I already give link

[@samudranugrahantoro5933]

Does this load cell need calibration load cells?

[@dheyaakadhim8375]

Thanks so much. How can we write those loads on excel sheet??

[@harikrishnanharikrishnan6074]

Which type of wires are used to connect this ?

[@msrutujapatil1787]

During uploading program it shows error occurred while uploading the sketch. What exact meaning of this error . I checked port many times . Please replay me

[@MartinNegrete-bp4zf]

Hay libreria para el ESP32 S2 KALUGA 1?

[@danemarmomekalfonso5624]

The zip file imported in the video are named "Liquidcrystal_12C-1.1.2" But in the link it is named "HX711_ADC-1.2.12.zip" is this the same zip file?

[@humayunjawed7751]

What is the component behind the lcd display?

[@passiontechklm]

I2C or build in i2c LCD display

[@PavankumarBatchu-b8m]

we want to measure the weight of the backpack. Can The load cell sensor that you used in the video be able to give the weight of the backpack in kg(kilograms) i.e., up to 10-120kgs.? Please reply.

[@syednizarwannoh1099]

Can i connect Any coloured wire of load cell into the hx711? Let's say i connect the red wire to E- is there any difference?

[@africantech5]

Yes

[@NWONKNU273]

What about the calibration factor ??how do you get that value?Will they change for different objects or stays constant

[@z3r0rvm19]

Calibration factor can be determined by performing Calibration. It can be done by going into the examples folder then under the HX711_ADC folder there is an example called calibration. Read the instructions carefully and perform it, at the end it will show you a calibration factor which can be used here.

[@NWONKNU273]

@@z3r0rvm19 thank u🤗

[@yusufbyahatti1552]

after calibration program how to dump this program in arduino

[@duangjunthanikkul9487]

@@z3r0rvm19 0

[@tsalazar3289]

Can this set up be done without a laptop? Or is the laptop the power supply to the display?

[@passiontechklm]

Laptop is to upload the code only, after done upload the code you can remove the laptop and power Arduino by other power supply between 5 to 12vdc.

[@Joelprb]

Is the code ready to use?

[@abhaychaurasia8576]

Was this load cell used immediately after purchase or was it used after calibrating it?

[@urvish6649]

Thanks brother

[@hanyelatal6953]

I want the simulation pls

[@Mannuyadav567]

Fatal error: failed to connect to esp8266 time out

[@mariahhafizah5208]

While upload sketch, when it say connecting... u should press hold the boot button on esp8266 . Release the button after it done

[@jmch1369]

Thank you,,,

[@aiii73]

Circuit diagram plz

[@Aishwarya_06]

Please Provide Circuit Diagram AS Soon As Possible

[@nazmulalam3108]

cannot measure 200 kg load cell

[@Aishwarya_06]

Please Sir Provide Circuit Diagram As Soon As Possible

[@aiii73]

Have u done project?

[@aiii73]

Plz reply bro

[@sushmithamoguloji1155]

Provide zip file

[@passiontechklm]

Please check in description I already give the link

[@abdulazizshaikh7598]

Any one please help me out, after connecting all the components. In LCD display this one indicates = IV DOSED ( ML) If any one know about this please help ke