How to mirror the TGH-FMM forward motor mount on the GSPEED V1-C1 Chassis to run Axial AR45 axles

How to mirror the Team Garage Hack forward motor mount to allow for proper drive shaft alignment when running Axial AR45 axles.
gspeedchassis....

[@Islandwalks]

Just a tip to others, to prevent the drill bit from running, bolt up the triangle piece with both fasteners. Take your bit and drill through the hole in the guide to make your hole in the frame rails. Unbolt it and do the same to the other side.

[@petroskaramichalakos5891]

Great information... I love your products and all the support and innovation from you as well as all the companies that support the hobby...

[@GSPEEDCHASSIS]

Great to hear bro. Thank you

[@dragonflyjoyride]

Nice job Gabe! This will come in handy when my new axle come in. Thanks

[@GSPEEDCHASSIS]

Thank you

[@Blacksheeprc2024]

Thanks gabe this is why I gave up on my c1 cause I couldn’t figure it out 🥺😂

[@rezzrollinrc]

Ok Mr. Gspd I’m a believer of all tha hype bro trx4 v3x4 zr2 just pulled a krazy insane vertical Rez line man 🤯🤓 stay safe man!! One last thing hell of a chassis and Rez approved man✊🏽✊🏽🤓.. Good info on vid too bro..

[@GSPEEDCHASSIS]

Awesome bro! Thank you!

[@joeygodoy509]

I think you keep the drilling gig on while drilling new hole.

[@billderas3420]

Hi Gabe. Would the transfer case installation for this mirror change have no overdrive? So, OD would be achieved at the axles. Thanks.

[@carlpetre9112]

Great video! Does this have to be done to run AR 45 axles? I'm kinda in process of building V1C1 and was planning on using ar45's.

[@GSPEEDCHASSIS]

Yes

[@bingsunbren]

Will you add the mirrored skid as an option for the V1-C1 chassis kit? Please 🙃🙃

[@GSPEEDCHASSIS]

Mirror skid won't be part of a package, but you can purchase the V1-C1 rails and hoops separate. V1-C1 should be back in stock in a couple weeks

[@bingsunbren]

@@GSPEEDCHASSIS got it. Looking forward to building a C1 with ar45s with a combination of TGH and GSpeed stuff.

[@stevenmadison6706]

Will your new chassis be coming out with those holes predrilled or is that something to come?

[@GSPEEDCHASSIS]

No. The shock hoop brackets is what needs to be drilled on the V1-C1 and they come with the transmission, not the chassis so holes will still need to be drilled in the future

[@miniboom007]

What are the specification for the bearing and spur gear that you used? Thanks.

[@GSPEEDCHASSIS]

V1-C1 package deal gspeedchassis.com/collections/v1-c1-performance-parts-and-packages/products/gspeed-chassis-v1-c1-package-deal Square chassis spacers gspeedchassis.com/collections/tgh-v3-products/products/gspeed-chassis-square-spacers . GSPEED G-LD servo mount gspeedchassis.com/products/gspeed-chassis-g-ld-laydown-cms-servo-mount . Hard body mount sliders for the RC4WD Mojave ii hard body 2 door gspeedchassis.com/collections/v1-c1-performance-parts-and-packages/products/gspeed-chassis-v1-c1-hard-body-mount-sliders . Forward motor mount and 30% overdrive transfer case gspeedchassis.com/collections/tgh-v3-products/products/tgh-forward-motor-mount-for-v3-chassis-and-30-overdrive-creeper-t-package . I'm running the TGH-FMM forward motor mount and transfer case with AR45 axles. You'll need the TGH mirror drilling jig kit to assist in laying out new holes to drill in the front shock hoop brackets in order to mount a mirrored front motor mount. gspeedchassis.com/collections/v1-c1-performance-parts-and-packages/products/tgh-mirrored-drilling-jig-forward-motor-mount-kit Instructional video on mirroring the front motor mount kzbin.info/www/bejne/nqKqi2mimc50gNE Instructional video on mirroring the Creeper T transfer case kzbin.info/www/bejne/jXnToXiNoamme6c . Suspension link kits can be purchased here. There are drop down menus to select the parts you are building with, like AR45 axles and G-MP panhard mount. hardcore-rc.ecwid.com/G-Speed-V1-C1-AR45-Portal-Kit-p367791960 . Wheel base- 11.75" Front and rear drive shafts- 105mm Center drive shaft- 70mm You can use drive shafts like..... supershafty.com/products/supershafty-mip-hd-driveline-individual-parts_pos=1&_sid=087864444&_ss=r&variant=12160250708062 Or www.amainhobbies.com/axial-wb8hd-driveshaft-set-2-axi31133/p-qtqqtqtqymzxactz . 3Brothers RC 👇👇👇 www.3brothersrc.com/product-page/anti-foams-4-19-1-pair G14 servo gspeedchassis.com/products/g14-direct-power-servo?_pos=1&_sid=76baf2e7a&_ss=r 3Brothers RC 2750kv motor gspeedchassis.com/products/kratos-ten-2750kv-10-pole-sensored-brushless-motor?_pos=1&_sid=db51ae6a0&_ss=r Recommend Team KNK hardware 3mm screws, nuts and washers gspeedchassis.com/collections/team-knk-hardware/products/team-knk-hardware-700-pcs-monster-bag-stainless-hardware-kit Assorted spacers gspeedchassis.com/collections/team-knk-hardware/products/team-knk-hardware-aluminum-spacer-variety-pack-natural

[@hanau73]

Is there a vid on the v3 mirror?

[@GSPEEDCHASSIS]

Not at the moment. Basically the same steps just a different shape of shock hoop brackets

[@smokong]

Bro i have gspeed chasis otw if im using front motor mount do i need still drill a hole to install the front mount

[@GSPEEDCHASSIS]

What front motor mount?

[@smokong]

Tgh forward motor mount

[@GSPEEDCHASSIS]

If the TGH forward motor mount was purchased from the GSPEED Chassis website, it comes with shock hoop brackets that don't need to be drilled if not mirroring the mount.

[@stevenmadison6706]

Probably a stupid question but will the A.R. 45 straight axles mount the same? I haven’t seen them in comparison, just asking for a friend lol

[@GSPEEDCHASSIS]

They mount the same, but the drag link is longer

[@stevenmadison6706]

I just ordered some hard-core links for my V1C1 and the straight axles

[@brandonisabelle7996]

Where can I get just the drilling jig

[@GSPEEDCHASSIS]

Message Team Garage Hack. They may be able to help you with that. [e-mail]

[@suyaafpv6835]

What are the font and rear bumper ? Handmade?

[@GSPEEDCHASSIS]

facebook.com/Bentmetal-798536523527216/

[@MartyCortez]

next time start all the screws before tightening...