This video is really helpful. Anyway, how to get combined hardening parameters of steel bar since we just have yield stress, ultimate stress, yield strain and ultimate strain values?
@Professor3MEC3 жыл бұрын
Thanks for appreciation. Combined hardening model requires cyclic stress strain data to be used to identify kinematic hardening parameters. So may be look for cyclic stress strain data and then try to fit the kinematic hardening parameters with experimental curves. Process of identification will be similar to the third option discussed in the following video. kzbin.info/www/bejne/mJewhmRjpLR_p7M
@MuhammadMuzammilAzad-q7y2 жыл бұрын
this was really helpful. can you guide me how to proceed from here it we require SN curve of a mechanical part.. Thank you
@Professor3MEC2 жыл бұрын
for SN curve, i presume you are after high cycle fatigue for such analysis you may have to consider FE-Safe with ABAQUS which might have a different name now.
@MuhammadMuzammilAzad-q7y2 жыл бұрын
@@Professor3MEC thank you for your response. I am working on it now. If you can make a video on a similar problem, that would be so much helpful. Thank you
@moeinjalilian93052 жыл бұрын
Thanks for your tutorial. I have a question. can I have one cyclic Load in the first 10second of analysis and then have a different cyclic load in the last 10 seconds. first Cyclic Load is Force-Control and the latter one is Displacement-Control.
@Professor3MEC2 жыл бұрын
yes for a simplistic case, you will have to create two different amplitude cards and then link them to first force and then to displacement. If need help then let me know and I am try to create a short video.
@Professor3MEC2 жыл бұрын
Here is a video on this kzbin.info/www/bejne/qJbOhpqZecdrf8k
@structurelearninghub33406 ай бұрын
It is possible to run cyclic loading in Analysis Type : Static General?
@Professor3MEC6 ай бұрын
Yes 🙌🏻 t should be for quasi static cases. For inertia effects might be better to use explicit step.
@johncarter401012 жыл бұрын
Hello sir. I want to simulate linear motion caused by cyclic loading on object. i.e:- with each cyclic loading object will translate in forward direction for each cycle , how should I do. Currently my object is not moving in forward direction but , just undergoing cyclic loading on same spot. Please give any tips....
@Professor3MEC2 жыл бұрын
could be related to loading and boundary conditions did you make sure that you are not fixing the active degree of freedom in the cyclic loading direction? or send me the model file and I can have a quick look.
@parth76123 жыл бұрын
I want to incorporate the cyclic loading parameters K and n and want to perform cycles until low cycle fatigue occurs in the component. What should be done? Could you please help?
@Professor3MEC3 жыл бұрын
I have replied to your email.
@victorokpanachi23042 жыл бұрын
Thanks prof. Pls, How can the wheel tracking test be simulated using Abaqus software?. Most especially the load application of the wheel. The wheel (700N (weight); Diameter (200mm); 50mm (contact width); contact length (20mm)) performs a back and forth movement on a sample of asphalt concrete (300mm by 260mm and 60mm thick. The wheel moves with a speed of 26.5 cycles per minute and is supposed to ply a to-fro distance of 230mm on the asphalt concrete, it also reaches it maximum velocity (305mm/s) at the center of the pavement. The wheel will cover 10,000 cycles in the experiment. The experiment is designed to simulate the rutting behavior of asphalt concrete. Please help prof.
@Professor3MEC2 жыл бұрын
I will think of a simple example based on above and create a short tutorial soon.
@victorokpanachi23042 жыл бұрын
@@Professor3MEC Thanks Prof. You are the best.
@yosefgirma6553 жыл бұрын
thank you it is helpful. please help me. i have a lateral drift history(drift ratio vs lateral drift) but i have no amplitude vs time history. how can i get? am using Abaqus for simulation. The specimens were tested by controlling lateral displacement at the loading point. Lateral displacements were increased from 7.25 to 203 mm in stages, and load cycles were Repeated three times each displacement stage.
@Professor3MEC3 жыл бұрын
Get the loading data as a function of time from experiments and using the same approach shown in the video create amplitude function. Good luck
@akwaajohn1243 жыл бұрын
Please how do you apply both static and dynamic load on an element at the same time
@Professor3MEC3 жыл бұрын
Are all the loads in same direction? Please send more details. 3minutesengineeringconcepts@gmail.com
@rezauldewannayan42243 жыл бұрын
i want to know who to do numerical investigation of stress field for anisotropic bonded joint
@Professor3MEC3 жыл бұрын
Following might be the ones you are looking for? kzbin.info/www/bejne/rp67e3-HnJaqd6s
@Professor3MEC3 жыл бұрын
kzbin.info/www/bejne/jYXWiXqDi6anrbM
@amrmasoud55803 жыл бұрын
How to consider the pinching effect during cyclic loading in Abaqus?
@Professor3MEC3 жыл бұрын
In general, pinching effect is widely observed in the hysteretic behavior of RC structures. According to experimental studies, the pinching effect is associated with crack closure, shear lock, slippage of longitudinal reinforcement, and so on. I am not an expert on concrete, however if you could send me some more info on what is required I may be able to create a simple video on that.
@amrmasoud55803 жыл бұрын
@@Professor3MEC OK, well, I want to mention that the main problem of general-purpose FE softwares as Abaqus and Ansys , that they do not consider directly the pinching effect during cyclic loading, I will be thankful if you prepare other video for this case. Thanks
@abhaygopinath1593 жыл бұрын
Hi, thanks for the video- it's very helpful. However, how do I apply acceleration in 3 directions simultaneously? the tabular input will be like following time, x-axis vibration, y-axis vibration, z-axis vibration 0 x x x 1 x x x 2 x x x 3 x x x
@Professor3MEC3 жыл бұрын
Thanks for the appreciation. You may create three amplitude curves instead of one if they are different in each direction. Then when you create boundary condition, you can assign separate amplitude curve to each boundary condition. I hope i was clear.
@lintapaul3108 Жыл бұрын
Sir I'm doing CFST column steel beam joint connected with bolted connection subjected to cyclic loading at beam end After running I'm not getting strength degradation portion in the result In property module, I have given elastic and plastic property with combined hardening Still I'm not getting strain softening region Please help.
@Professor3MEC Жыл бұрын
Can you explain more on what causes softening under cyclic loading during experiments? This would help suggest a few options. Also, what material properties have been used? Does the material shows isotropic and also kinematic hardening during the cyclic loading?
@lintapaul3108 Жыл бұрын
@@Professor3MEC formation of plastic hinge is the reason for strength reduction
@Professor3MEC Жыл бұрын
i am not aware a direct method. If you can provide more details or research paper then I can suggest something.
@LasteventsBlogspotalsanea Жыл бұрын
Can I do the cyclic load test in Ansys?
@Professor3MEC Жыл бұрын
yes you can do that.
@MJs-853 жыл бұрын
does ABAQUS calculate sine in radians or degrees ??
@Professor3MEC3 жыл бұрын
This link may be helpful. abaqus-docs.mit.edu/2017/English/SIMACAEPRCRefMap/simaprc-c-amplitude.htm In the amplitude function its sin(omegaxt) where omega is in radians/sec
@gokulsivakumar49303 жыл бұрын
Sir instead of applying displacement load.. Is it possible to apply pressure load over a circular area in a cyclic way
@Professor3MEC3 жыл бұрын
Yes it should be fine. Instead of displacement boundary conditions, go to loads and select pressure and then use any amplitude function.
@gokulsivakumar49303 жыл бұрын
@@Professor3MEC Problem i m facing is i dunno how to do loading time and resting time repetitions in cyclic case... Predefined ones do not serve purpose for me :(
@Professor3MEC3 жыл бұрын
@@gokulsivakumar4930 Email me your model file or model details. I will then try to create a short video.
@gokulsivakumar49303 жыл бұрын
@@Professor3MEC your mailid sir
@Professor3MEC3 жыл бұрын
It’s in about section of the channel. Thanks
@AminRahimi-12 жыл бұрын
where was the material details?!!!
@Professor3MEC2 жыл бұрын
Please have a look at this one for properties kzbin.info/www/bejne/rp67e3-HnJaqd6s
@AminRahimi-12 жыл бұрын
@@Professor3MEC thanks I will watch it :)
@matsualaidrus81732 жыл бұрын
This video so awesome! I wanna ask sir, how to model the hamburg wheel test into abaqus ? Here is the video: kzbin.info/www/bejne/i2KYgoqupN-So8U Thanks sir
@Professor3MEC2 жыл бұрын
Thanks for liking the video. If you could please send model dimensions and loading conditions I can create a short video.
@Professor3MEC2 жыл бұрын
Models can be donwloaded free from www.professor3mec.com Please do support the channel at ko-fi.com/professor3mec All proceedings go towards new videos and keeping the webpage going.