How to program a Honeywell FocusPro TH6000 series thermostat

Here we show the steps on how to program a Honeywell FocusPro TH6000 series thermostat. Including the advanced programming step to set the thermostat into Auto mode enabling the thermostat to switch between heat and cool automatically. Turning off the heat strips so they do not ever come on saving you money.
Here is the link to the manual so you can review every option for more advanced settings.
customer.honey...
www.amazon.com...
Follow me:
Instagram: / talesofmatt_
FB: / mmblogusa
Twitter: / talesofmatt

[@apakabar9022]

very confusing video

[@sunnym2227]

Hi Mr. Matt I’m not sure what the settings were before the changes started because I never used the heat as much as this year, which has been pretty cold. I appreciate you contacting me back. I saved your video as a reference because your explanation was easier for me to follow. Thanks again.

[@TalesOfMatt]

Glad it was helpful. 👍🏻

[@lewisreader1756]

Thank you brother Mr Lewis Reader

[@idaniaesparza3881]

Damn! Could you have been more fucking confusing!!

[@weiscracker]

Ours is set for Celsius and I can’t figure how to get it to Fahrenheit

[@mdiazdiaz5612]

I just called Honeywell to try and get some help with a non working thermostat only 2 years old. What a bad bad experience I had I was on chat with two individuals the first one disconnected me after about 30 minutes, he kept on asking me the same question in different ways his name was Tonantzi and the other Alexander, oh my god he ran out of stupid questions. With this experience i swore i will never buy a Honey well thermostat again.

[@SayITProductions]

My unit fan has been cutting off and on randomly but won't cool down my house pass 72..should I factory reset on the thermostat?

[@somebody6048]

Before you turn off the heat strip and change function 1 from 5 to 1, you need to check function 6 to see if it is at the default of 5 for gas and oil furnace less than 90% efficient, as evidence by your thermostat in this video. As that would make the thermostat think you have cheap auxiliary heating from gas and will run the auxiliary heating all the time not knowing that it is expensive electric heating. If it is at the default setting of 5, then you need to set it to 9 so the thermostat know you have expensive heat strip as auxiliary heating and it will try to run the heat pump more often. But if you turn off the heat strip, then when it gets really cold, you won't have the heat strip to help supplement the heat pump to warm the room up quickly when needed. Try that first before turning off the heat strip. Note: Everytime you change the setting of function 1, all the other functions are reset to the default thus you have to cycle through all the other functions and make sure it is appropriate to your situation and not at the default setting.

[@mz.bell-c7673]

My thermostat won't turn off...HELP

[@ivanshaw2229]

This video was so helpful! Thank you!

[@jimmyjawbreakrful]

my Honeywell has a mind of its own trust me....so confusing'

[@schiaa7340]

I used your advice on the settings for auxiliary heat not to come on. Now I have no heat. Gonna change it back.

[@rocksinsocks787]

I followed your video. Now, even in cool, it blows hot air. I had the thermostat set at 63, and it climbed all the way to 83. I had to change setting one to “cool only” in order to stop from dying from heat stroke in my own home. Could you explain why this happened?

[@bebetigre1252]

dont play with this like he shows,go to other videos.too advanced you could really mess up

[@saulEGaray]

Same thing in my house

[@amandafarmer1111]

Do you know how to fix this? I did the system override and temp is now 76° when setting is 67°…

[@Albertojedi]

Thanks. Those settings aren't shown on the User Guide that I downloaded from the link you provided. Which manual shows the lists of settings shown in this video?

[@TalesOfMatt]

Alberto González, I thought I had provided a reply the other day. Sorry about that. Here is a great link. www.manualslib.com/manual/1021687/Honeywell-Focuspro-6000-Series.html?page=5#manual

[@Albertojedi]

@@TalesOfMatt Excellent. Thanks!

[@blancacdlr1460]

Thank you so much! Your video was very helpful. We were trying to figure out why the thermostat was heating when we program it to cool. We programmed it in the wrong way. Thank you again 😊

[@bigpapaadam1]

Omg thank you so much! That crazy auxiliary heat was driving me nuts! Couldn’t figure out how to turn it off! Finally got it disabled from watching this video! 🙌🙌🙌

[@TalesOfMatt]

Outstanding, I was in the same boat a few years ago and so I went on the hunt to find a solution. Once I did I was super excited and had to share with others. So glad you found the video and was able to make the adjustment. Happy New Year!

[@josuetorres8414]

I did it and now the heat does heat at all it just blows air

[@josuetorres8414]

the heat does not work know

[@christinasworld1553]

How do I take off the program on it

[@samd9545]

Someone messed with my thermostat and now its showing a cooling option which it never had before...originally only had a heat on/off option...I want to take the cooling option off so what do I do so I only have a heat option on there! Help! Lol! Please and thank you!

[@raquelb731]

I am just trying to figure out how to put the ac on 😂 my kids are gone and they would put it on for me

[@zoewaltonhansen4572]

I'd like to set the thermostat to go on at 5:30 am at 74 degrees and the manually adjust it all day. It is off all night. Is there a way to do that? Do you do one on one zoom or phone sessions?

[@efrainmartinez6600]

Thank you!! I messed with the setting it went down hill till your video helped me fix the problem

[@TalesOfMatt]

Efrain Martinez great news, glad you found the video and was able to fix it.

[@TallCloverFarm]

Your video just got my heat back on as I had inadvertently changed one of the Advanced Settings which shut down my heater only gas furnace. Thanks to you I'm warm again. Thank you very much!

[@TalesOfMatt]

I’m very happy the video help. 🙏

[@ChorteBoy512]

How do I get my Honeywell focuspro 6000 thermostat to blow cold air again in the settings or do you think it might need some freon and my ac did turn off and on by itself and now it's not or does that take a minute to go back to its original function after messing with the settings

[@TalesOfMatt]

Hello Dario, The thermostat controls what your units is to do, blow hot or cold and at what tamp. If you have it set to cold and it is not blowing cold air, than I would think it has to do something with the until and not the thermostat.

[@tikadrought6591]

Thank you, thank you. This helped and I can do this knowing what I am doing!

[@TalesOfMatt]

Tika Drought outstanding, glad the video was helpful.

[@vSwampFox]

What is the regular setting without the schedule?

[@mrzee1958]

On aTH4210 how do I get into "settings" and then "preferences" then "smart response technology" to turn "recovery mode" off (and to turn off "energy saving mode" ? Thanks

[@kelvinraysutton]

Ty you just save me some money 💰 lo e it

[@tiki40341]

If 1 and 1 is heat how to change it to air?

[@Jarrettj1115]

Thanks for making this video man i would never of known ..my first electric bill (over$1k) brought me here.

[@TalesOfMatt]

Glad it has helped you out.

[@djony007]

I see you turned your aux settings from 5 to 1 to reduce the use of auxiliary heat but I need to do the opposite. it’s taking to long for the auxiliary heat to click on and just blowing cold air for 10 to minutes or so making the house cold again and it’s just counterproductive I will like for the auxiliary heat to click on sooner so I’m guessing I go up to like a 6 or 7 ? or is There separate setting for that ?

[@sweethaven1929]

My husband and I were wondering why temp was 70 when we want 74 (seniors,limited tech) temporary was flashing … re going to do as your video , I

[@scottconrad6654]

Thanks for the tips. My thermostat wasn't going the the scheduled temperature, So I went into the setting you showed how to get into and changed my 1 setting. Heat kicked in right away. Setting was 1 and 0. I set it to 1 and 1. Hope this winter ends soon. It is springtime!

[@TalesOfMatt]

Hello Scott, glad the video helped you out. It seems like winter is just now coming to an end. You should be all set for next year. If you have any questions down the road feel free and let me know.

[@r.hazelwood4885]

Where do I or where did you get the White with Black text in the left corner?? I need this to change programing on my Thermostat... Thanks!!

[@greenophotography]

I just installed the Honeywell Home FocusPro TH6320R along with the THM5320R equipment interface module (EIM). After having successfully linked the two and gone through the thermostat setup, I notice that under the “System” panel I am able to toggle through “Heat,” “Cool,” and “Off,” but not “Auto,” which the manual indicates is an option. Any idea why I’m not seeing that as an option? Many thanks! Excellent tutorial, btw.

[@socorrotaitt9332]

My AC is not cooling properly. What is the left bottom button for? What should I set it ? Appreciate your help. Thanks

[@serinephosphate]

This was incredibly helpful! Thanks so much!

[@TalesOfMatt]

You're very welcome. Glad it was of use to you.

[@liamsnow4642]

Is there a way to turn of the fan? I just want a.c or heat to flow. The fan randomly turns on even when a.c or heat isn't being called.

[@TalesOfMatt]

Interesting issue you have, first off sorry for the late reply. Are you saying the thermostat is set to off and the fan still comes on? If the thermostat is not set to off, it has to be set to something that makes the fan come on. Let me know the settings when the fan comes on and I'll see what I can do to help.

[@aboutimeYluj]

I have this problem. Even when i turned it off, fan on auto, the fan would still come on usually at night. What could be the problem?

[@bigmike4950]

@@aboutimeYluj Do you have gas heat and electric air conditioning system? If so it should be set to 1 - 0.

[@ien2023]

Im about to throw this garbage in the trash. their menu system is annoying. I recently had to reset the wifi and it mess up my heat set up.

[@mariocasarez6043]

Hello, thank you for the video. Can you explain what the ac does when it's on auxiliary mode? What exactly do the heat strips do and how does it make your electricity bill higher? Thank you.

[@TalesOfMatt]

Mario Casarez Hello, the setting that I talk about to turn off the heat strips from kicking in does not impact the cool/AC settings. As far as the heat strips go, they heat the house (at least should) a little faster. However; based on theelectricity rate in your area the heat strips might be too costly vs the time it takes to heat your place. In my case it was too costly vs the gain in heating my place just a little faster. I hope this helps.

[@mariocasarez6043]

TalesOfMatt thank you for the explanation!

[@hammerhead957]

I was monkeying with that setting that was shown in the video & made sure my Thermostat was set at 1 & 1 & now it is showing us Celsius temperature. How do we fix that?

[@LeslieAngelle]

HOW DO I RESET IT!?!?

[@samd9545]

How do I take the cooling option off? I only want the heat on/off option on there... Someone messed with my thermostat! Please help!

[@trinityguerra1495]

Hello there ! I have a question my thermostat for cooling is in 1 and 0. I am wondering if that is the reason 1. The temperature is so different upstairs and downstairs ? 2. My bill is really high. Any suggestion for the advance settings ? Thank you in advance.

[@ReneRodriguez-yw5nc]

Gracias por compartir tu talento con nosotros!

[@ShawnLivesInItaly]

Thanks

[@alpaslanserdengecti4305]

Thank you! When I forgot to set functions, I watch you😂

[@TalesOfMatt]

Wonderful, I’m glad the video was helpful.

[@haleygros9379]

Been wrestling with this thing for weeks. This worked. Thank you

[@TalesOfMatt]

Haley Burkett my pleasure and I’m glad it worked for you. Winter is coming and it will save a great deal in electricity. Happy to help.

[@theebaddestbrat9051]

do you know how to change the INSIDE temperature ? mine been on 80 and it's burning

[@Kimgomez2012]

Mine says in recovery on top of the time. Anyway to turn that off?

[@oldmanpops8810]

Where do you find the temperature limit settings or function list 1-?

[@bornintoacorruptsystem9to5]

Hey man is there a way to program that thermostat for whenever the ac clicks off to keep it from going on for 4 minutes bec my ac can’t go on wen it first shuts off bec the condenser will burn out so like let’s say it clicks off but someone goes to turn it back on the thermostat knows not to turn it on until 4 minutes after it shut down I just want to know if this thermostat could also be set that way so I don’t burn out my condenser if u could please respond back to me I will appreciate it thanks

[@TalesOfMatt]

Hi, well the thermostat is just a control and your unit will do what it is told to by the thermostat, there is no system within this until that would limit the unit from being turned on within the 4 minutes that you are talking about. Sorry I could not be more help.

[@donnalima5522]

Thank you so much it was very helpful!

[@michellestenvold2762]

Helpful, but does this one connect to WiFi at all?

[@angelyanamorales6633]

Thank you man you save me 70 bucks

[@TalesOfMatt]

Outstanding, that is great to hear. The power of the internet at work in a positive way. So glad this video has helped so many.

[@niatinson5766]

I live with roommates, the inside temperature doesn’t change at all when I change the cooling to anything…how do I undo it ?

[@TalesOfMatt]

Within the video, there is settings that limit the changing of the temp and it can only be set between two numbers. I’m traveling for the holidays and with family now or I would watch it again and point you to the time I’m the video to focus on.

[@sunnym2227]

Hello Matt. I moved into a house and the temp was already set. Lately it’s been cold and I tried to change the setup to my preferred setting so the house stayed a little warmer. I wasn’t understanding the 1 and 1 setup so I didn’t finish programming to run how I preferred. Well now I believe I threw it off because at night when I press heat 80/auto it blows out cool air and then in the morning when I press heat desired temp, it blows warm. How do I reset to override current settings so I can put it in 1 1 mode and do as you did locking it on no higher or lower than setting and do I have to go through the set schedule and manually set each day. Last question is there separate schedules for summer and winter. I really appreciate you responding and providing help. God Bless.

[@TalesOfMatt]

Hello Sunny, to answer the 2nd question first. There is now setting for the seasons throughout the year. The reason for this is they don’t begin and end on set days weather wise. Based on your comment, I would suggest re-setting it to where it was before the changes and start from the beginning. Also, I would set each day differently based on your sleep schedule to maximize the schedule and minimize the electricity cost. I hope that helps, if you have any other questions, please let me know.

[@unorthodox7945]

Thank you so much! Great video

[@maxisenberg9093]

manual doesn't have advanced settings...

[@willlopez5448]

Very helpful. Good detail video

[@MrTacoma]

How to hard reset?

[@l.sternin3318]

Q: How do I reset the schedule?

[@KKerak]

Crushed it thank you

[@wssl3843]

You save me some money, thank you!

[@1776Based]

Christ...

[@mariannepayne4453]

Thanks, but how can I set a temperature 'at will'... as in the old thermostats. I live here. I don't need to program various hours that the system operates, but just adjust the thermostat based on our needs. THANKS for your reply, because often I want more heat, and I cannot get it to come on at all!

[@TalesOfMatt]

Hello Marianne, just so I understand, the heat is no but it doesn’t go as higher as you would like or it does not come on at all?

[@mariannepayne4453]

@@TalesOfMatt Good morning. Thank you for your reply. This is an older system. (10 years) The manual seems to have been lost. I cannot make the thermostat do anything! It keeps asking me to program time, then days of the week that I want it to control.

[@TalesOfMatt]

@@mariannepayne4453 that makes sense, is seems. It seems like the system is sitting in set up mode as if it has been plugged in for the first time. You will always need to set the time and date. This is needed incase later down the road you want to set an on off schedule. It might also ask you to do that as part of the set up, you can just toggle thru that without setting it up. I believe once completed you should be good to go.

[@mariannepayne4453]

@@TalesOfMatt Thank you, Matt. I will try this. Your suggestion sounds promising. Marianne

[@NJ-yd8hj]

Lost

[@AngelaSalazar-tr4hm]

No disese como

[@kimberlylopez5636]

Hello I want to thank you! The video was exactly what I was looking for my bill was almost 500 dollars! Its been using the coils. Now I can't wait to see what the next bill will be! Be blessed 🙌 🙏!

[@somebody6048]

See my post a day ago about why you don't want to turn off the heat strip.

[@schiaa7340]

@@somebody6048 what video is that. I don’t see it.

[@somebody6048]

@@schiaa7340 Basically I said that the thermostat set the auxiliary heat to gas by default on function 6. And that you want to change it to the correct setting of electric. Otherwise it will use the heat strip as much as possible for quick heating because it think you have cheap natural gas for heating. But if you set it to electric, then it will only use the auxiliary heat when really necessary. In addition one person I know had their system broke down when they went back from vacation and turn it back on and didn't have the fan running continuously. And that is because the thermostat think it is gas and turn on the heat strip without running the fan thinking it is a gas, thus turning on the gas and letting it reach temperature first before running the fan, which is standard procedure for gas. But turning on the heat strip without the fan running burn out the heat strip. So this person always have the fan running continuously not knowing that it could have been avoided if they set the auxiliary heat to electric instead of the default of gas.

[@pelumi7]

This is very helpful bro

[@TalesOfMatt]

You're welcome

[@randysanico7738]

How to set Fahrenheit to Celsius

[@TalesOfMatt]

Randy Sanico Hello Randy, I hope all is well. At 5:37 in the video top left of the screen is an image. It is within setting 14, function 0 = Fahrenheit 1 = Celsius

[@randysanico7738]

@@TalesOfMatt thanks

[@Mazel_Tov_888]

which function allows you to change cycles/hr on cooling?

[@TalesOfMatt]

Hello Ric, I'm not sure I fully follow can you share a little more details and I'll take a look and see what I can help with.

[@Mazel_Tov_888]

nevermind

[@Luckie382]

Go over more precisely or slowly or something pls!

[@Dwelly70]

Make sure you say “ that being said alot of times. Because we didnt no you were saying anything. Wow

[@uncleskeetxxl]

Thank You