HOW TO Program Car Garage Door Opener | ALL MODELS

Program your car garage door for all models. Works on Subaru, Ford, Toyota Lexus, GM, Jeep, Chevrolet, Mercedes Benz, BMW, Nissan, Kia, Cadillac and Honda, Chrysler and Doge Ram.
STEP 1:
You will reset your Homelink unit buttons by holding down the first and third buttons for 20 seconds for units with green lights and 10 seconds for units with the Homelink LED light. You will know the unit has cleared all the codes when the light flashes rapidly.
STEP 2:
Push and hold the Homelink button you would like to program while pushing your garage door opener at the same time.
(Homelink LED lights in Mirror - If you have a home link LED house in your mirror, you only need to push it once. If the light or dot does not stay on, you will have to hold it down at the same time as well)
This will take five seconds with most remotes. If you have a newer LED, it might take 20 seconds.
If your garage door does not open, pair the unit to the garage by pushing the learn button in the garage door motor. You will have 30 seconds to return to your care to push the button. Hold your cars Homelink button for about two seconds. The garage door light will flicker. Push your button a second time and this will activate your door.
Some garage door openers require three pushes of your button. If you you push your button and see two triangles flash rapidly, push your button for 2 seconds and it should open.
#programcargaragedooropener
#programcargarageopener
#Programhomelink

[@funshoarashi6102]

This didn't work directly until I ran into the below comment on another forum. Hoping this might help someone as well. 'You took the door opener remote to the car and had the car learn from the remote and then you pushed the yellow learn button on the opener and within 30 seconds you pushed the HomeLink button in the car three times getting the correct number of blinks of the LED in the car so the opener could learn the codes from the car' After pairing with the door opener remote, you need to pair with the learn button.

[@strategyandperformance]

Thanks for sharing this with this community!!!!

[@timothystament2217]

I tried both ways with my new 2024 RAV4, Finally went to Genie Support, Model 1055TKV. 1. Clear HomeLink (HL) codes. 2. Press remote for 10 seconds (do not release) 3. Press HL button until light flashes, release both buttons. 4. Press Genie Program button on opener (Blue light flashes) 5. Press HL button for 1 second release, repeat 2 more times. My door opened on 3rd push. Your video was a great help in getting me started.

[@strategyandperformance]

Thanks for sharing with this community!

[@kimberlysaucier3963]

We moved to a new house (new garage door opener), I’ve tried to sync our Highlander to the door opener no luck, I just gave up and used the remote 😩. We just bought a new Subaru, tried multiple times to program it to homelink ( even called garage door company), watched 3 KZbin videos, still no luck ☹️. Finally I watched this video, you are the ONLY person who said the car had to be facing the garage 😳 ( didn’t have issue with only house garage was big, this house we have to back one car in and the other front in)….SOOO, it worked. Thank you, both cars are now programmed. By everyone assuming the cars were forward facing, screwed me up. Thank you.

[@strategyandperformance]

Thank you for your kind words. I am glad I was able to help!!! Great job programming both cars!

[@arunkrishnan147]

THANK YOU! This was the only video that mentioned the 2 step process for rotating code - pair through the remote controller first AND THEN do the 'Learn' pairing with the garage opener. Other videos I watched had one or the other only. Thanks again!

[@strategyandperformance]

Thank you for the support! I’m glad it helped!

[@salty-syrup]

Can’t believe I waited so long to program my cars, that was easy! Worked with Ford and Kia. Thanks.

[@strategyandperformance]

Awesome! Happy to help, and Thank you for the comment!👍

[@MarkusLaumann]

You just saved me about $40 trying to replace the old overhead garage door openers that are crapping out on me. Thank you!

[@strategyandperformance]

I’m glad it helped Boss!

[@mickrodriguez3724]

Ty sir! I spent 30 mins reading my owners manual and surfing for help. I tried multiple ways to get the openers to link up to no avail and gave up (for awhile). I them stumbled on your walk through. Yours worked. I followed it step by step and won! :-)

[@strategyandperformance]

I am so glad I was able to help! Thank you for the kind words.

[@smithbilly10]

Excellent instructions

[@strategyandperformance]

Thank you boss!!

[@DavidWilliams-mr5nl]

This has been the BEST garage door pairing video I've found!!! The ONLY one that actually worked!!! Thank you sir.

[@strategyandperformance]

That’s awesome! Thank you for the kind words!

[@sylviakenobi]

THANK YOU!! This is the only video that has actually helped and targetted every issue I had!

[@strategyandperformance]

I’m happy it helped!

[@damiansalvatto6880]

I've watched about 8 other videos including from Toyota and the genie (the garage opener i have) and none of them worked until i watched yours. I appreciate this.

[@strategyandperformance]

Thank you, boss! I’m glad I was able to help!

[@damiansalvatto6880]

@@strategyandperformance no problem! 💪🏾

[@josephvasquez9787]

Best video!! Tried other videos and couldn't get functioning. Thus was way more thorough!

[@strategyandperformance]

Thank you. I’m glad it helped!

[@user-io3py4yw9v]

Thank you! My garage door opener is an old model, so I had to pair it with the learn button. But it works now- thanks again!

[@marylinbishop1626]

Quick and clear instructions. Thank you!

[@strategyandperformance]

I am happy to help!!!

[@Shadowsatthe]

Excellent video and explanation, my case was the extended step + one more but it worked, thank you very much!!!

[@strategyandperformance]

Thanks for your support! I’m glad it helped!

[@MyrnaLydia]

Very informative and helpful!

[@strategyandperformance]

Thank you! I’m glad it helped.

[@HooLeePhucingSheet]

I have a slightly different mirror. The 2020 camrys kind of have another led besides the green/red. I reset them but I still get the green solid light.

[@ChrisWalton-ipadtestkitchen]

Thank-you for making this video. Very helpful!

[@strategyandperformance]

Thank you boss! Glad it helped!

[@bsg8686]

Huge help! Thanks a lot!

[@strategyandperformance]

I’m happy to help!

[@kathysims9]

Worked great. Thanks!

[@strategyandperformance]

Thanks! I’m happy to help!

[@markrob205]

Very good video man!

[@strategyandperformance]

Thank you boss

[@cleansebob1]

How to clear only one button at a time was priceless. Thank you!

[@lorenzocroce767]

Jesus loves you!

[@strategyandperformance]

Awesome! I’m glad I was able to help!!!

[@chrisa1844]

Great video bro, thank you....after watching so many videos, your video explains perfectly for my 2019 bmw M850i convertible and my dad's 2020 bmw x5. Thanks

[@andyheenpella5417]

Programmed easily. Thanks.

[@strategyandperformance]

Thank you!!! I’m glad it was easy!

[@TheDelamp]

Thank you so much for the well documented information. VERY WELL ARTICULATED

[@strategyandperformance]

Thank you Boss! I’m glad it helped!

[@keepcalmsmokeon]

Worked right away, thanks!

[@strategyandperformance]

Excellent! Always happy to help!

[@DontSuckGolf]

Man you are a lifesaver i could not figure this out for the life of me lol thank you!

[@motorbikematt]

This worked! Thank you

[@strategyandperformance]

Im glad it helped Boss!

[@wolfsoul11]

Thanks! Your video succeeded where others failed me.

[@strategyandperformance]

Excellent boss! I’m glad it helped! It’s not perfect, but I was trying to be as thorough as possible.

[@robfoster4716]

Very helpful!

[@strategyandperformance]

Thank you! Happy to help!

[@yohanroberts4058]

Great video thank you for sharing

[@strategyandperformance]

I am happy to help! Thank you for your support!

[@EnemyFire]

Did you post a video on how to program to a community gate? I hear you mention it at the end of this video. Thanks

[@owendaugherty4912]

GREATEST VIDEO OF ALL TIME!!!

[@strategyandperformance]

Awesome!!! I’m glad it helped.

[@kraletisandhya]

Thank you so much!! That really helped me program in my car❤️

[@strategyandperformance]

Excellent! Happy to help.

[@mattj5820]

wow thank you for an easy to follow video I got it done in under a minute

[@strategyandperformance]

Thank you boss! Happy it helped.

[@MichellePotter-yq4bm]

Just bought 2023 Forester. I do not have the hand-held remote any longer for my garage door opener. Is there a way to pair these if I cannot possibly perform the first step of using the hand-held opener?

[@bachoy88ledz25]

Thanks for the video dude.

[@strategyandperformance]

Welcome! Happy to help!

[@HinesEdventures]

dont forget to tell people your car needs to be OUTSIDE for that last part to work! i was trying it and failing cause my car was inside the garage when i tried to program it using the learn button on the garage door opener.

[@strategyandperformance]

Great point!

[@rickfeng4466]

this is so annoying! I have an over-height garage, which means I'm not tall enough to click the Learn button unless standing on the car's door frame. have to get a ladder And it doesn't work DX

[@sapphiresleeps]

Thank you for this. Same thing I thought I could do it inside my garage but finally it worked!

[@techcorpllc6712]

Thank you for your help

[@strategyandperformance]

Happy to help!

[@HappyGirl1972]

I did it!!!! Thank you!!!

[@strategyandperformance]

Welcome! Happy to help!

[@gsnowakowski]

Mazda CX-5 2016: 1. Garage Door Opener red button pressed once for a short time. 2. In less than 30 seconds pressed and kept pressed the button on the mirror until the garage door opener blinked and then pressed again to see the door closing. Thank you.

[@strategyandperformance]

Thanks for sharing! 👍

[@AdrianRodriguez-sj3lx]

Thank buddy, great job with the video!!

[@strategyandperformance]

Thank you, I’m glad it helped out!

[@firstlast-yn4qg]

whoa it worked. all i had to do to open is hit the old opener like always after hitting the mirror button that do nothing with the programming.

[@steves048]

Would you happen to know where the learn button is located on the Genie Model 7155L. I looked all over the manual and I can't find it's location. There is a square buttom marked PRGM only that I see. Thanks.

[@strategyandperformance]

That it. Did that work?

[@keitharndt790]

Is it possible to save the frequency from a car button to a remote. WE lost the remote that has the community gate code.

[@caseymoore4463]

Good vid!

[@strategyandperformance]

Thank you. I’m glad it helped.

[@nataliebrown8020]

Thank you

[@strategyandperformance]

You're welcome. Glad it helped.

[@Emilyjcarey]

👍🏼👍🏼 for 2 cars!!

[@strategyandperformance]

Thank you boss!

[@matmorgan4765]

Do you absolutely have to have the garage door remote? Or can you program it without one?

[@dennismazurek961]

I tried to sync my new 4 runner with the garage door opener and only wound up wiping out my key pad and remote codes

[@jasonmiller1616]

Trying to program my rav 4 and having trouble. Everything seems to work properly with flashing green light but it still does not operate the garage door. Any ideas?

[@strategyandperformance]

Did you try pairing it with the garage door? Instructions are towards the middle of the video.

[@grizzy909]

How do I clear the middle (2nd) button only? I wanna program that button next & it might be set up to another garage, I dont wanna have to reset them all since I am using the 1st button on the very left, its a 2008 Acura also if that matters. Thanks

[@strategyandperformance]

Ill tell you, but if you need a visual, I show you how to do it right after we program the first button in the video. Get the garage remote control in your hand, push the button you want to reset and hold it in your cars unit. It might take 10 or 20 seconds. When you notice the blinking pattern change, push your garage button remote in your hand and make sure it’s next to the unit in the car while holding both buttons. When your cars button indicator light changes pattern the second time, it has the signal. Now you can open the car garage. If you have a car garage with a revolving code, you will need to program your car signal with the garage receiver. I show you how to do that in the video. Good luck!

[@grizzy909]

@Strategy and Performance Thanks for responding so quickly, I should have mentioned I dont have the clicker to get in, I use a key to open the garage, so is it possible without the clicker?

[@linvicky423]

I would like to know If I program the remote opener does it effect the number code key pad opener?

[@strategyandperformance]

No it does not.

[@fonzarellyplay370]

Can I do this with more then one house? Can you please tell me the steps if you can please? Thank you.

[@strategyandperformance]

Yes, you can if you have multiple buttons. It’s the same for every button. If you watch the hole video, you will see how to reset one of the buttons.

[@djbabygggudani7911]

I have a 2008 Mercedes and a chamberlainb550 and nothing works !!help

[@keithm1961]

didn't work 2009 Lincoln chamberlain opener. chamberlain tells me there is a transmitter I need that will let opener talk to car

[@neneemack5934]

Does this work for apartment gates?

[@strategyandperformance]

It depends, you’ll have to check with the management. Technically, it should. Some of those gates are similar to subdivision gates.

[@juderamnarine5617]

Idiot here. It worked as prescribed. Thanks.

[@strategyandperformance]

Awesome!!! LOL, it’s not intuitive, it took me for ever to figure it out. Thanks for the support Boss!

[@twylasouthall374]

How do i sync code to 2 different cars if new house does not have actual remotes

[@strategyandperformance]

The toughest question so far. If you have a car garage but are missing the remotes, you’ll have to look up the manufacturers website and find out if you can program a new car garage remote with their receiver unit. The hard part is how how close you need to put that new garage remote to the actual box. If it’s not close, you may be able to program your car unit by being parked two or 1 feet behind the garage box above your car. If that doesn’t work order a cheap garage door opener compatible to your garage door to program it. Once that’s programmed you can use that garage remote to program your car units.

[@twylasouthall374]

@@strategyandperformance thanks, will give it a shot.... have no idea what the previous owners did with the remotes.

[@turan5058]

Dude My Car is Toyota Avalon 2014 my garade door opens But does not close With Homelink

[@strategyandperformance]

Oh no!! Did you try pairing it with your garage? Those instructions are later in the video. If it’s fixed let me know. Some people might be able to do the same thing if they have that problem.

[@fhuezo]

Can you reset only one of the buttons without resetting all of them?

[@strategyandperformance]

Yes, if you watch the video, I go over it a little further down.

[@ericfuehrer8520]

I tried syncing my Genie garage door opener both ways numerous times to a 2014 RAM, 2014 F-150, and a 2024 Expedition all right in front of the garage and none of the vehicles homelink were synced to my opener. Any other suggestions????

[@user-qf8uv7lm6u]

👍🏻

[@kimberlybraud1914]

Lift master set button

[@jennymilburn5977]

👍

[@strategyandperformance]

Thank you!

[@alicebrunson4688]

We are having trouble pairing a 2006 Toyota 4-Runner to a new 81600 Liftmaster. Even the experienced installer couldn’t solve the issue. My question is, Wouldn’t pressing the LEARN button clear out the garage remote, the extra remote and the other vehicle already paired and working?

[@iamcarrot1]

Doesn't work

[@user-rl9rx1pu8k]

Put mask on please😊

[@brady9561]

I must be dumb. I didn’t understand most of this.

[@strategyandperformance]

You are very smart my friend. 1. Reset all the buttons (hold 1st and 3rd button at the same time until the light flickers fast. 2. Push the button you want to program and hold it, then push and hold your garage door opener remote button and hold it next to the car garage door button you are holding. When the button light flashes fast it’s done. 3. Push the button to open the car garage. If it does not open, look at the video on the section to program your garage receiver.

[@zduke7]

Thank you

[@strategyandperformance]

I’m glad it helped! Thank you for your support!