Well made and to the point video, thank you sir. It's satisfying to watch that hunk of rusted iron become new again!
@aubreyj.tennant11234 ай бұрын
Great vid! Thanks for the detailed information. I’m about to do my 95 Mitsubishi with tandem rear wheels & dual wheel cylinders on each side. 💪👍🥂
@Impreza_S20610 ай бұрын
very informative video, just rebuilt the rear brake cylinders on my 1982 moskvich 412 and now it finally stops!
@danielalamo207511 ай бұрын
Another reason to rebuild your old stuff, new crap comes with metric bolts. Which can be a pain when everything else on your old American made truck or car is SAE. I just had this problem with the clutch/ brake master cylinder on my dad's 1963 GMC pickup. But I had to use the new one.
@Reddirtrodz11 ай бұрын
That's a fact! I hate mixing metric and sae!
@fuzzjunky Жыл бұрын
mine wasn't seized, but was very surprised about how simple the whole thing is. i even used some new parts of a slave that didn't fit, cleaned mine out and it looks like it will go back together with the new cylinders real easy. [i kept the old slave bodies because they had the right fitting bolts - the new one didn't]
@TEH47 Жыл бұрын
Is it basically the same for a 1962 Buick wheel cylinder? Thank you, Tim H.
@Reddirtrodz Жыл бұрын
Yes, all wheel brake cylinders are essentially the same.
@matthewmoneta79064 ай бұрын
When you were hammering it, it helps to have an actually solid fixture.. all your force was gone considering you were working on a trampoline.
@fabio404 ай бұрын
For less than $20 just go out and buy a new one. By the time you pay for Evaporust and a rebuilt kit it would be cheaper to by a new one.
@Reddirtrodz4 ай бұрын
Yes, IF a new one is available, they are not always available.
@mikecoffey52118 күн бұрын
Yep, find me a new one for a 1954 Willy’s aero.
@ken24007 ай бұрын
I take it the outside where the seal sits was cleaned up too? Thanks for the video.
@Reddirtrodz7 ай бұрын
Yes, the entire body was cleaned.
@JhariilTV5 ай бұрын
may I know what type of grease did you use??? Thank you...
@Reddirtrodz5 ай бұрын
This works great. www.amazon.com/Permatex-24125-Ceramic-Extreme-Lubricant/dp/B0018PSASU/ref=asc_df_B0018PSASU/?tag=hyprod-20&linkCode=df0&hvadid=312141533517&hvpos=&hvnetw=g&hvrand=6581805064370921952&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=1024339&hvtargid=pla-571820984777&psc=1&mcid=58ef3728bbd03119962338b384fa6144&tag=&ref=&adgrpid=61941536837&hvpone=&hvptwo=&hvadid=312141533517&hvpos=&hvnetw=g&hvrand=6581805064370921952&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=1024339&hvtargid=pla-571820984777&gclid=CjwKCAjwnv-vBhBdEiwABCYQA7Spq5DBViMAKv3LRQBG_gxQjpqNcCwPOWQ2_d54U0uJnFCvz2RHzBoChH8QAvD_BwE
@link5606336 ай бұрын
Shoot none of mine local shop have the kits for my truck and online they asking for about the same price on a new complete cylinder. I wanted to rebuild it to learn from the on hand experience but I guess buying a new cylinder is my option.
@Reddirtrodz6 ай бұрын
That's no bueno!
@marjanstojkovski9093 Жыл бұрын
What if i don't have hone tool? Is it very important to hone the cylinder bore?
@Reddirtrodz Жыл бұрын
You need to clean the bore. If it is not pitted or scored, then you can get away with just cleaning it up with an ultra fine scotchbrite pad. That said, , brake cylinder hone costs about $10 to $15 bucks. amzn.to/3NFN2pa
@fuzzjunky Жыл бұрын
i'm doing it at the moment. i'm gonna use some 1500 grit paper and some CRC and my finger. i'll let you know how it goes. i've used some CLR to dissolve any alloy decay powder. i just cannot buy any more tools i'll only use once so as long as there's no pitting i think it should be fine.. my cylinders and rubber seals are brand new so half the problem is solved
@Reddirtrodz Жыл бұрын
@@fuzzjunky it works just fine how you are doing it, as long as there isn't much pitting.
@fuzzjunky Жыл бұрын
@@Reddirtrodz yeh it seemed to go back together nice and i made sure it had that nice travel that you did in the video. as long as it doesn't leak tomorrow when it goes back on i'll do the other side the same.
@dgriffin60746 ай бұрын
May I suggest you be more specific? You keep stating "diesel"; diesel what? fuel? Also, you applied "grease" to the plunger; it looks like silicone grease, but you don't specify...
@Reddirtrodz6 ай бұрын
Im not sure what else diesel would mean in this case, but yes, it is diesel fuel. The grease was an oversight, it is DOT hydraulic brake grease.
@paultimoti8704 Жыл бұрын
grease in a brake cylinder ?? That does not mix with rubber and brake fluid
@Reddirtrodz Жыл бұрын
There is a tiny smear between the piston and the cup, this is not going to see brake fluid. This is how I was taught by an old timer. This is Marine grease, it is specifically formulated to be compatible with rubber seals and prevent corrosion from water. Another option would be silicon paste. Some wheel cylinder kits come with piston grease. The metal pistons only see brake fluid when the seals wear out. There is no grease in the cylinder itself, just a tiny dab to keep the cup from welding to the piston.
@eng-aholiccustomz20046 ай бұрын
Wow 3 days on 1 wheel cylinder! I could have done 80 in 3 day's.
@Reddirtrodz6 ай бұрын
The rebuild process takes 20 minutes, but this one was seized, so we let it soak. That's not typical, this one had sat for years and rusted up. That said. This process shows that you can save even crusty old wheel cylinders!
@onegorgeouschick4 ай бұрын
@@Reddirtrodz Amazing
@davepeters3606 ай бұрын
NEVER EVER USE A PETROLEUM PRODUCT IN THE BRAKE FLUID SECTION! ALWAYS USE FRESH BRAKE FLUID ONLY.
@Reddirtrodz6 ай бұрын
This was DOT grease, which is brake fluid safe.
@chaneli48555 ай бұрын
I just pretended it doesn't come out😂...
@blakessite8 ай бұрын
For 3 more bucks could have got a rebuilt complete
@rosewood17 ай бұрын
Accept that for some vehicles new parts are not available
@scottschmittmusicАй бұрын
So you're saying spend $4 more dollars and buy a new one lol
@ReddirtrodzАй бұрын
@scottschmittmusic not all wheel cylinders are available new, and this is the kind of skill that could be very useful someday.
@philipadcock35085 ай бұрын
Diabetes tattoo?
@Reddirtrodz5 ай бұрын
Yessir. Pass out in a walmart parking one too many times and you figure out you need one!