I think that’s reasonable prices. Well done that man.
@The13pilgrim2 ай бұрын
Many thanks for the modification.
@DenisPittaway2 ай бұрын
Thanks for the Video.. Can you tell me what Version of Firmware you have running there and also which HF mod board is Installed in the radios.. Cheers Denis
@Rex-G8UBJ2 ай бұрын
its CEC_0.51HF the board is a mk2 version which includes a small audio amp to increase the volume on SSB
@robertdmaiden69032 ай бұрын
Works well rex,just getting my head around all the settings. Do you think there's any advantage if you also modded the unit to the 2 antenna .
@Rex-G8UBJ2 ай бұрын
@@robertdmaiden6903 maybe if you need vhf at the same time, but to be honest there is no loss on hf and swapping antennas isn't a big chore
@electronbox2 ай бұрын
very nice i will get in touch as i want to purchase one
@la7dfa2 ай бұрын
If you want to listen at home, I would advice getting an SDR dongle. Much better selectivity and real sideband, not DSB.
@Rex-G8UBJ2 ай бұрын
Thanks but I have an FTdx-101MP at home, this is a cheap solution for going portable
@rosscopeeco69Ай бұрын
Does this have modified internal components or firmware?
@Rex-G8UBJАй бұрын
@@rosscopeeco69 Yes and yes, two components are swapped out then two components removed Then an hf pcb with an SI4732 chip is installed. The firmware CEC_0.51hf is then installed...
@The13pilgrim2 ай бұрын
Excellent video. I've just emailed you for details. Thank you
@ominkan312916 күн бұрын
I have tried to listen to HF without the mod at 18.000 and up. But I can not receive anything even though I can receive on other radios like my ATS 25 max decoder. On the the uv k5, I am running IJV 3.40 firmware. Sadly in another uv k5, I tried to install the v2 mod board but accidently removed the subminiture black chip to the right of the removed FM IC. Do you know the value of that chip, hopfully I can replace it.
@Rex-G8UBJ16 күн бұрын
@@ominkan3129 these radios are using the hf mod board for reception. The software CEC_051.hf is also required. the radios do work down to18mhz without the mod but I don't know how well
@Rex-G8UBJ16 күн бұрын
@@ominkan3129 assume you didn't remove the 8 pin sil chip, the small device to the right is a 1k 402 resistor and carries data so I won't work without it. Its an easy fix if you have a stock of 0402 resistors
@ominkan312916 күн бұрын
@@Rex-G8UBJ Yes I can say about mine, not well.
@ominkan312916 күн бұрын
@@Rex-G8UBJ Thanks so much for your help. I did solder the kit of the v2 mod board and installed it. When removing the 8 leg chip I also removed the 402 chip that you identified for me. There is another 402 on the left side as well. That one remains. Only the right side is gone and needs to be replaced. You are right, the radio is not letting me input anything. Definitely a needed part. My radio doesn't see the Mod board so I must have made some kind of mistake while soldering all the SMD components. Thanks again for your replies.
@patricklegein6969Ай бұрын
hello my friend , i just had my uv-k5/8 from china, today, what do i need to do the mods ? i have the program cable as wel, do i need the egzumer for the software ? greetings from Bruges Belgium
@Rex-G8UBJАй бұрын
@@patricklegein6969 ypu will need CEC_0.51hf firmware, then add the hf pcb with SI4732 chip
@patricklegein6969Ай бұрын
@@Rex-G8UBJ thanks for the rep.i have a look tomorow
@davehorton94625 күн бұрын
Hi do you sell the radio with the HF board fitted 73 Dave G4XIB
@Rex-G8UBJ25 күн бұрын
@@davehorton946 yep, 39.70 including postage
@Rex-G8UBJ8 күн бұрын
Hello Dave, yes drop me an email and I can supply most variants modified and ready to go g8ubj.io91uj@gmail.com
@Rex-G8UBJ2 ай бұрын
no problem, you can find me on QRZ.COM, or email me at g8ubj.io91uj@gmail.com VY 73 G8UBJ