How to remove a gear box from a Scania lorry truck mobile mechanic hgv semi rig tight release bearing
Пікірлер: 41
@RobertSmith-fv3ux3 жыл бұрын
Thanks for that, what I use under trucks is a large piece of spray suppression, spicky side down Great in the wet Keep them coming mate
@Professional-struggler3 жыл бұрын
The re-con box isn’t here till next week and it’s going to be raining so might have to give that a go rob cheers pal
@RobertSmith-fv3ux3 жыл бұрын
You are welcome
@richardlaw57372 жыл бұрын
Ha, wish there was that much room round a Coach gearbox. Luckily most of our fleet is auto these days, years ago we had some manual Mercedes with V6 engines. It as much quicker to take the engine out to do the clutch, we done it that often the bolts undone themselves 😂.
@saifswabi8927 Жыл бұрын
Tanx for vedio..now i see this vedio morning i open geer ..i not understand this lock ..how open...tanx ❤😊
@stevencoyne4971 Жыл бұрын
Great old Video Chris !👍👍👍
@jimmyquinn963911 ай бұрын
Another good job Chris 🚛🚜🚚👍👍👍👍👏👏👏👏⭐️⭐️⭐️
@mikeday4348 Жыл бұрын
Mate get yourself a length of 2 inch box section, warm it up and put a bend in the middle. Undo the top gearbox mounting bolts ( the 4 24mm head ones). Now jack up the engine and gearbox together. Slide your box section under the flywheel housing and sit it on the suspension springs. Some models you can just put thick bar straight across the springs and sit the engine on it. The way to get the clip off is to lever the bearing forward while you release the clip with the other hand. If it doesn't come out straight away lever it forward a few times
@kenfox19113 ай бұрын
Do you work on these gearboxes regularly?cheers ken fox
@kenfox19113 ай бұрын
@@mikeday4348 👍
@mikeday43483 ай бұрын
Not any more mate, i retired a few years ago. I worked for scania in the uk for 12 years and scania in australia for 8 years.. I've fitted more clutches than i care to remember. Don't think I'm one of them people that only worked at dealerships. I've worked everywhere and on everything before i worked for scania. Like yourself , i could get the wipers working off the P.T.O if i had to, or was paid to👍🏻👍🏻
@kenfox19113 ай бұрын
@@mikeday4348 did my last message come through?cheers ken fox
@brentsmith5647 Жыл бұрын
Brilliant man ❤️👀👀👀👀👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
@jamesward5721Ай бұрын
Bits of wood are tremendously important when cocking about with bloomin gearboxes. I tend to find.
@jamesward5721Ай бұрын
Scania probably sell main-dealer spec bits of wood with logos on & whatnot. I just use aftermarket ones - I find those come in a wider range of dimensions. The handiest size I have is 4"*4" - those get used for everything.
@jim810003 жыл бұрын
You should be able to get the release bearing easier by pushing the bearing from below with the lever and squizing the clips, once you squize you pull the bearing with the leaver and it's out ... No need to remove the slave cylinder just remove the 22mm air and the fluid line despite these great work
@Professional-struggler3 жыл бұрын
Cheers pal I did try that it was tight but it might of gone if I got someone to push the clutch at the same time as squeezing the clip 👍I want the job done as quick as possible! It takes longer and more cost to loose all the fluid than just take out the three mounting bolts of the slave and launch to the side
@karlmallion67072 жыл бұрын
I wouldn't remove the fluid line. Just adding another job to the ticket. And if it doesn't bleed up properly your adding a headache. I always just take the slave off complete. But horses for courses.
@kenfox19113 ай бұрын
Do you pull these gearboxes out regularly?cheers ken fox
@bijuthattamparambil7395Ай бұрын
Bro, good job🎉
@Yoyoyoyoyo729272 жыл бұрын
Hey Chris, I absolutely love the work you do and love even more the knowledge you are passing on to us, I’m attempting to take the transmission out of my 1999 ford iveco 75e15 I’ve never done it before and I can not get the clip to release, I have no wholes at the top or bottom for better access just the whole where the arm goes through, I’m going to have to take the arm bolts out somehow for it to slide out, what size are the bolts, and if you have a better suggestion for access that would be great
@Professional-struggler2 жыл бұрын
Don’t know size they are of head mate, might be hard to get to the arm bolts, you might be better taking the pressure plate bolts out, it just means you have to turn the fly wheel round to get to each bolt, good look wizKid….. lovely bank holiday job that 😬😁😂
@ciprianodcosta22352 жыл бұрын
New models very easy to remove whereas the old mixer truck you got to remove the front gear housing and remove 2pcs allen key bolts to change the release bearing fork assembly
@kenfox1911 Жыл бұрын
Hi Chris how do you remove a scania 4series gear knob ?cheers ken
@ΞΕΝΟΦΩΝΡΟΜΠΟΤΗΣ2 жыл бұрын
Hi Chris. I would like to make a question.i have a p410 8x4 scania.it doesn't gearing from 5-6 gear makes noise to rear gear sometimes and doesn't go automatically below 1st gear.some advise please.thanks alot
@AmazingTechnology12 жыл бұрын
Good man
@Professional-struggler2 жыл бұрын
Thanks mate 👍
@fejzullamurtezani Жыл бұрын
We have man tgx 18.470 gearbox scania opticruise. It keeps jumping to neutral and won't drive. Please help! 😢
@andyg8172 жыл бұрын
Chris , what about the release bearing going back ON to the pressure plate when fitting the box. Is it a pig ???
@Professional-struggler2 жыл бұрын
No mate keep your clip closed and just push it in with a ply bar through the bell housing holes 👍
@sundramasiva23453 ай бұрын
👌👌👌
@ryanbennett1024 Жыл бұрын
Scania G/Box lot easier in a pit.
@kenfox19113 ай бұрын
Do you know much about pulling these gearboxes out ?cheers ken fox
@ryanbennett10243 ай бұрын
@@kenfox1911 yes mate, we have a Scania fleet so I’ve done quite a few. Great effort doing it on the ground by the way. But using a pit or ramps is way easier. If you have access to that stuff.
@kenfox19113 ай бұрын
OK I've got a 20ton ramp ,my scania is a old 4 series andi think the slave cylinder is on the way out ,its the type that is on the thrust bearing ,do you know if the box comes straight out or does it have a clip on the bearing, cheers ken fox
@kenfox19113 ай бұрын
@@ryanbennett1024 👍
@ryanbennett10243 ай бұрын
@@kenfox1911 to be 100% honest mate, I’ve never worked on one that old before, but I’d imagine it would have a clip.
@cumbrianrider89032 жыл бұрын
i guess this is a pull to release clutch rather than a push to release? i work on cars and don't come across many pull release cluctchs, peaugeot/citroen used to use them late90s/early20 and they were a ball ache