hey my fellow Nitro Brother! Great tips as always for a super common Nitro Rc issue. I once had this issue ( you might have seen it with a buddy's T-maxx 2.5 on my channel). The bearing was so stuck, I tried everything, including a vice and punch, broke through the backplate. Basically had to just buy a new backplate, only solution at that point.
@thebug40463 жыл бұрын
Hay man yes I believe I remember seeing that crazy how that can happen! I have never ran into one that bad before
@scottl5910 Жыл бұрын
This happened to me with my Tmaxx 3.3. To prevent breaking the backplate, I used an 18mm deep socket to put the backplate on, and used a punch to drive the one way bearing off. The socket allows the starter shaft to fall into in, but holds the backplate from moving. Worked for me
@rcsendandblast15793 жыл бұрын
I found my answer right here in this video. Thanks for doing this video I see now how the motor is apart and now feel safe to take mine apart 👊😎 I have a motor to diagnose. I hope it cleans up and works. It is ceased I believe it’s ceased from 30 years of sitting 👍
@georgeganjei65732 жыл бұрын
Hi! Great video with good tips. Would fine steel wool work for cleaning the one way shaft instead of 600 grit sandpaper?
@thebug40462 жыл бұрын
No problem! And sure you can try it a SOS pad should definitely work. Good luck!
@duckboy172 ай бұрын
I'm having the issue with the one-way bearings slipping and and replace it with a new one way bearing and still the same thing .I believe it's the starter shaft I'm not 100% sure
@thebug40462 ай бұрын
Try buff the starter shaft with some 800 grit if that doesn't work replace the starter shaft
@duckboy172 ай бұрын
@@thebug4046 yep I buffed the starter shaft and it worked and I'll order another one
@Ben-dj1bu2 жыл бұрын
Excuse me I don’t have a cold thanks for asking 😂 😂 😆 nice 😂
@thebug40462 жыл бұрын
😆 🤣
@victortakeda93383 жыл бұрын
Hi Thebug 404 i’ve been having trouble with my carb in my nitro Rs4 2. It was gummed up and I haven’t had a good past with Carbs so if you don’t mind, I do recal you having nitro star .15fe engine so can you please make a video of how to take a nitro star .15fe carb apart and cleaned. Thank you
@thebug40463 жыл бұрын
Hey you can usually just clean them with non chlorinated brake parts cleaner that will unstick them and clean out the varnish you do not need to remove the throttle barrel most of the time or the low speed needle but you can disassemble the high speed needle i believe I do have a video on cleaning carburetors which will be the same process for all engines I think one of the videos is labelled how to fix and rc car that only starts when you put fuel in the carburetor i have one of those carburetors but I'm not going to take it apart for a video as it is already damaged and barely hanging together
@russl36322 жыл бұрын
good advice... also remember that 40 bucks you owe me- I think its on your counter
@thebug40462 жыл бұрын
That was for the weed guy. Lol
@dustinplee50672 жыл бұрын
I drill started mine and now it won’t grab how can I make my one Way bearing grab again all the pins and in the one way bearing and I soaked my one way bearing and shaft and my one way bearing will not fit in my ez started gear how can I make it fit it will get stuck when I put it by my ez started thanks
@thebug40462 жыл бұрын
Yeah you have to be really careful when drill starting because the drill will make enough torque what will just destroy the bearing itself or if the engine is flooded you will break the connecting rodder to other damage like bend the crank shaft You have to use your torque settings and just be really careful
@jasonmoody96738 ай бұрын
hi m8 my is same will do what you say ///// i was going to get new one / you are aill ways right thanks for this you make me lol on your videos to 😁
@thebug40468 ай бұрын
Hopefully it helps you good luck! 🍻
@Absolutecorn57673 жыл бұрын
the one way shaft sanding trick only works so many times unfortunately. usually sanding the shaft lasts only a few pulls before slippage again
@thebug40463 жыл бұрын
It works awesome but yes if you do it to much it won't help at that point replace the starter shaft and bearing
@donaldcarolus35943 жыл бұрын
I was told by the fella at my LHS to just take the bearing out of my EZ start tmaxx, and soak it in some of the trucks fuel….. shake it, and then put it back together. What say you??
@snorttroll4379 Жыл бұрын
what say you!!. is it a solvent basically?
@rc_teo_nade_2163 жыл бұрын
Ik you did this video for the post I did in the hpi Facebook page well it wasn't because of flooding the engine but because of the starter shaft was not 100 percent straight don't ask me how but now my starter shaft is broken and is leaking
@thebug40463 жыл бұрын
I have gotten the question about 7 or 8 times in here and others groups as well seems to be happening a lot lately