This is my first instructional video showing you how to remove the starting pin and pressure spring inside the HPI Savage X 4.6 big block motor
Пікірлер: 35
@bkehlin4 жыл бұрын
My God, thank you. I've been trying to figure out why my crank wasn't spinning. I bought new 1-way bearings and all. I had no idea my pressure spring was missing.
@firstpersonguy73304 жыл бұрын
Thanks for taking time to comment! Those springs deteriorate when the car just sits around. Since their want any ideas online, I figured a terrible video might help someone out there.
@BerryMan4273 жыл бұрын
Thanks dude; couldn't figure out why the plate wasnt contacting the starter pin. Papa bless.
@domasa7323 жыл бұрын
I used the same method to fix mine. Nice work!
@richcarrier19473 жыл бұрын
Nice v8d man you seem like a nice guy 😁
@davideabreu69992 жыл бұрын
i have the same exat problem where can i buy the pin and spring?
@jeffmagaiver64863 жыл бұрын
I only changed the spring, improvised by cutting a piece of the spring from a lighter since the pin does not damage easily, the spring breaks because of the heat. Besides, here in Brazil the pin costs a small fortune for such a small piece. Hugs man! Eu troquei apenas a mola, improvisei cortando um pedaço da mola de um isqueiro uma vez que, o pino não danifica com facilicade, já mola quebra por causa do calor. Além do mais aqui no Brasil o pin custa uma pequena fortuna pra uma peça tão pequena. Abraços cara!
@dickscrossedgarage3 жыл бұрын
I did the same! Lighter spring works just fine.
@ricabuiza54703 жыл бұрын
What lighter to your use
@CBRR-re2un2 жыл бұрын
Is lighter spring still working?
@brandonjohnson28572 жыл бұрын
How did you get the pin out mine is stuck
@firstpersonguy73302 жыл бұрын
Penetrating lubricant. A couple applications. Then tug on it with needle nose pliers.
@firstpersonguy73302 жыл бұрын
WD40 is what is used.
@brandonjohnson28572 жыл бұрын
I don't have enough to grab with pliers.
@firstpersonguy73302 жыл бұрын
Fudge. If I had the parts in front of me I may have some better solution, but if you giver lots of penetrating lube and let it sit overnight then turn it over and start slamming it on a hard surface? Might be enuff to bring it out to grab with needle nose pliers. Sounds like the spring behind it is completely corroded, and broken.
@anif83353 жыл бұрын
👍
@nickrenteria31023 жыл бұрын
Where did you order part from
@firstpersonguy73303 жыл бұрын
I removed the spring from a BIC lighter, and cut it to size. Its still working too...
@nickrenteria31023 жыл бұрын
About how long
@firstpersonguy73303 жыл бұрын
About 10/32" or 11/32" of an inch. I wasn't exact, but made sure the spring pushed that pin almost till it falls out of housing so it applies good pressure to the starting plate.
@nickrenteria31023 жыл бұрын
Alright man I replaced the spring still no luck
@nickrenteria31023 жыл бұрын
Spring was still in one piece
@crazydoctor87703 жыл бұрын
What is the one way size in this 12 or 14 HEX motor?
@GavinY3 жыл бұрын
14mm
@popeye90484 жыл бұрын
Where did you get the pin and spring from? This has went on a savage that I just acquired.
@firstpersonguy73304 жыл бұрын
The pin held up good and didnt need replacing. The spring I used was from a BIC Lighter, cut to the right length (it pushes the pin out until the pin almost wants to fall out)
@popeye90484 жыл бұрын
@@firstpersonguy7330 I've got the engine stripped down and the pin is stuck solid in the crank and there's not enough sticking out to grab it. Pulling my hair out here lol. Thanks for your reply 👍🏻
@firstpersonguy73304 жыл бұрын
@@popeye9048 man, it's been 3 months and not sure if you care anymore but just WD40 the crap out of it and dig around in the spring hole with a tiny Allen key.
@popeye90484 жыл бұрын
@@firstpersonguy7330 hey man, I got it out, rebuilt everything and got it running sweet as a nut 👍🏻
@furkii3344 ай бұрын
@@popeye9048how did you get it out?
@donaldtaylor47762 жыл бұрын
but how do you get the pin out
@Robert-Smith Жыл бұрын
I saw a video where they used a small torch to carefully heat the pin and it came out look for that video try not to heat the part too much or you might change the hardness of the metal. hope that helps I know the comment was 8 months old.