This helped a lot because I am a new rider and I wasn’t sure if the throttle was part of the grip and now I am relieved that it will be easier to change the grips than I thought
@rmatvmc3 жыл бұрын
We're glad this video helped you out! Thanks for watching!
@555Triss8 ай бұрын
Giving the grips a few cuts also helps them come off but obviously if you want to keep the grips you won't want to do that Thanks for the vid dude ❤
@5thid738 Жыл бұрын
Just watched a guy remove his grips with compressed air. That's the way to go! 👍
@TDJDriftersBoss8 жыл бұрын
Only use a single line of glue or that bastard isnt coming off. You can see 1/2 of the glue squeezing out in the video.
@pablodev49342 жыл бұрын
Buddy got glue all over 😂
@zackeryreid45035 жыл бұрын
He helped me put on my new grips
@ExclaimMediaDotCom4 жыл бұрын
I'd love to see a video on the ProTaper Micro bar grips! There has to be a trick... They are so thin that I blow them out constantly and have tried so many different techniques. Especially the Throttle side!
@danniebrown33968 жыл бұрын
Not to criticize you but, contact cleaner? why not use wd-40?
@tootallbob4 жыл бұрын
Because if you plan on re-using the grips you are removing, it's harder to remove the WD40 from the inside of the old grips and they won't stick to the grip glue. If you aren't using them again, just use a razor blade.
@EOMFDdaudits4 жыл бұрын
tootallbob sure it is. You ever hear of brake clean?
@linuscullinskoglund78883 жыл бұрын
Oil based solutions breaks the grips down
@brentmiller9044 Жыл бұрын
Because you'll oil the bars leaving a bond breaker between the glue and bar
@jakobstalheim51856 жыл бұрын
Thanks for the help, But I don't think contact cleaner is needed, I just wasn't sure what to do with the throttle side of my bike.
@noahhiscock65335 жыл бұрын
Hair spary on bars and glue in the grip never coming off
@jamesbowie1820Ай бұрын
I haven't tried using safety wires on my grips but I do carry a kit just like the one you are using in my bag when riding just because you never know. I don't do any jumps or wheelies (yet) anyways
@rmatvmcАй бұрын
You're right, you never really know what could happen while riding! Gotta keep that safety wire close. Thanks for watching!
@Mr10usdad2 жыл бұрын
I have never used the wire. How important is it?
@ZmannR2 Жыл бұрын
You can’t safely clear triples without em.
@JO3BID3N-is-a-P3D0 Жыл бұрын
lol i hate using wire. glue is enough for me
@builttoride0226 Жыл бұрын
Pro taper pillow top grips, you don't even need glue. They sit tight and don't move
@swingset19695 ай бұрын
I never use glue. Clear spray paint/clearcoat works way better and doesn't leave a big mess. Spray it into the grip, push it on, after it dries it's rock solid.
@loganhedrick97122 жыл бұрын
Am we take the wires off after a day
@mritalianhillbilly4 жыл бұрын
Everyone of them forget to tell you, make sure it’s not a grip that is permanently on to the throttle, some people buy the aftermarket ones that are like that and it’s not coming off you just got to get a new throttle.
@LACKSHACKallday Жыл бұрын
Thank you this really helped
@ShawnPrince3 жыл бұрын
Can I do tht wire trick with a zip tie? I have a mini bike.
@4strokefrosty2 жыл бұрын
Hey man I CANNOT get my throttle grip off idk if I have any contact cleaner is there any other way?
@rmatvmc2 жыл бұрын
Is it glued on? If it isn't, you can used compressed air to get it off but if it is, you will most likely just have to cut it off and try to scrape off as much of the rubber and glue that is left on.
@4strokefrosty2 жыл бұрын
@@rmatvmc tysm man
@sepe18374 ай бұрын
Do u have to use safety wire the ones I have on don’t have safety wire
@rmatvmc4 ай бұрын
I'm guessing you still have your stock grips? Stock grips will usually come glued on but no safety wire. When replacing them, I would recommend using safety wire. Grip glue works well, but it isn't uncommon for grips to still move without safety wire. Or just go to a lock on grip and you don't have to worry about any of that.
@jimbotti7190Ай бұрын
Wire us ridiculous
@MarkPoprozhuk5 ай бұрын
do i have to use the special bar glue can i just use gorila glue or somthing
@rmatvmc5 ай бұрын
Super glue will probably make them very difficult to remove but it's not a bad option. There are many options of grip glue that can all work just fine. I"ve heard of people using everything from contact cement to hair spray with good results.
@hreindustries7 жыл бұрын
but its such a pain getting grips off after using grip glue, I always never had a problem with grips slipping but I would only use the wire.
@tiukusti89905 жыл бұрын
When i swap the clutch side grip it never stays it still keeps twisting Do you have any advice for me
@henrik79665 жыл бұрын
@@tiukusti8990 put it on with hair spray, it will make it easy to slide on but will glue it when it dries
@pineapplepissant Жыл бұрын
Good god man. That’s a shit load of glue… and 3 ties?!? What kinda riding r u doing?!?
@reeceboy24383 жыл бұрын
Do you have to have the safety warriors on
@BRLVideos2 жыл бұрын
No they are not needed, it's more of just rider preference.
@crochead7756 Жыл бұрын
Is it fine to use grip glue without the wire?
@rmatvmc Жыл бұрын
You can definitely use grip glue instead of safety wire.
@JO3BID3N-is-a-P3D0 Жыл бұрын
i only use glue. u can also use both if u want
@kevinbulk7272 жыл бұрын
Why no use compressed air? Instead of scratching the bars.... I know it won't be seen but still.
@rmatvmc2 жыл бұрын
A lot of people don't have an air compressor but compressed air also works great!
@carsonmiller96585 жыл бұрын
If you dont plan on re using them just take a knife heat till its glowing with a torch and slice through them like butter. Just dont cut throught the throttle tube.
@streetrider114 жыл бұрын
Or just use a sharp knife?
@gogurt_st4 жыл бұрын
Can I use Carb Cleaner?
@fusster33034 жыл бұрын
I used carb cleaner and it worked just fine
@BRLVideos2 жыл бұрын
WD-40 also works fine.
@valtterim41683 жыл бұрын
Yo my friend kinda broke his throttle thing while removing girps because they were melted into it
@disneylandlover803 жыл бұрын
Yeah that's what happened to me. I'm going to assume your friend used a box cutter, that's what I used on my old bike. I did the same thing, just destroyed the throttle tube. Use the method in this video, it doesn't destroy your grips and you don't have to worry about cutting past the grip and into the throttle tube. The term is called vulcanized, its usually Kawasaki and Suzuki bike which have them.
@qportier639 жыл бұрын
Perfect. Think you.
@redneckracing88954 жыл бұрын
You can avoid all that and just buy ODI lock-on grips much better
@Team_Banchamek2 жыл бұрын
Yes but if you have a race throttle kit you can’t use lock-ons
@Goon2Rippa4 күн бұрын
This did not help at all, i have the throttle tube off and ima just eating it off with a knife because the cut thing and the air gun didnt do anything
@redneckwithajeep50015 жыл бұрын
I really need to replace my throttle tube lol. 3 fingers worth of grip isn’t enough
@NickW90 Жыл бұрын
Don’t think you used enough glue
@lukeperrine50784 жыл бұрын
What if I have twist and thumb throttle
@2jmartinez5064 жыл бұрын
what kind of bike you got wtf😂
@kaloebvaldez55603 жыл бұрын
What the hell you riding boy
@mactheplumber3839 Жыл бұрын
Cut the old off woth a razor knife. Idk why tf you'd pry the old ones off woth a screwdriver. You dont need grip glue. You dont need anything fancy. Just get a little butter cookimg spray and just make a quick pass down the bar. Super light coating. Not all sides. Just ine quick stripe down each bar end and you're done. Slide the grip on, you're done. Ready to ride the next day. Zero grip spin.
@joereed73263 жыл бұрын
Rock mountain high🍀💪
@michaelroginski23168 жыл бұрын
I BOUGHT THE WRONG GRIPS
@alex-dk2rj4 жыл бұрын
@@drev1 lool
@raredesign2 жыл бұрын
US: Nice looking RM ATV: "Pulls out the wire and destroys them"...
@baja85934 ай бұрын
4:20 imma call her
@andrebrodeur3253Ай бұрын
😂
@cant-get-right48142 ай бұрын
Just another Day playing the Victim!!
@borky1987 Жыл бұрын
3 wires and a shit load of glue... 😬
@Md52884 Жыл бұрын
What glue I needa get
@gioflores963 жыл бұрын
You don’t have to do the wires guys. It’s not worth it
@demmcylol81663 жыл бұрын
thank you so much for informing me im looking for grips for my kawisaki bayou 220 and i make my own money at a young age and i wasent looking forward to buying that stuff but should i still use grip glue?
@SneakyKittyGameDev3 жыл бұрын
@@demmcylol8166 Glue the grips always or use the hairspray/spraypaint trick. I've never used wires as I hate them
@gioflores963 жыл бұрын
@@demmcylol8166 yeah grip glue is relatively cheap you can get a small container that’s enough for like 6 grips total at a cycle gear store if there’s one near you for about $3. But also if you don’t wanna spend money on that, you can actually just use hairspray.
@SmithAndrew13 жыл бұрын
WIRES? XD!
@g000se993 жыл бұрын
standard spray paint instead of glue - thank me later
@g000se993 жыл бұрын
@Magnus Fjerstad yep - its real slippery then it drys and sets tight. its a elegant solution - but wear gloves ;)
@g000se993 жыл бұрын
@Magnus Fjerstad you don’t sound too convinced … let me know how you get on. Super easy.
@g000se993 жыл бұрын
@Magnus Fjerstad here - kzbin.info/www/bejne/bHamh6doj55rqa8
@IdealContracting3 жыл бұрын
@@g000se99 i remeber some friends of mine using hairspray back in the day. Had the same effect with going on easy and then drying
@IdealContracting3 жыл бұрын
@@g000se99 haha just wached the video you posted and saw he mentioned hairspray!
@TheFoxygrandpa69Ай бұрын
If you use wire, shame on you.
@Welpbikeitis4 ай бұрын
Wire is criminal 😊
@rmatvmc4 ай бұрын
Gotta watch out for the pointy ends of the wire wrap 😉