This is How to remove the Engine from a Dodge Magnum with a Hemi Motor.
Пікірлер: 88
@gravitykat11002 жыл бұрын
Those 4 “knock sensors” that you pointed out in the valley are actually the MDS solenoids 🥲. Just so no one gets confused 👍
@crazysexycool18010 ай бұрын
Thank you please like, share, and subscribe, also please check out my other channel Salem Taxi, on KZbin for more material on a different level.
@leagente7 жыл бұрын
Very nice run down of parts, location & even oil change & a bit of safety. Lots of info in a short, compact video. Thanks man.
@TheFabian4218 жыл бұрын
On AWD models, the front driveshaft runs through the oil pan, so you need to remove the axles and differential. also, the 4 parts in the engine valley are MDS solenoids, not knock sensors. they shut off 4 cylinders to save fuel under certain engine loads. I actually want to deactivate mine because the exhaust drone when cruising is terrible when the MDS kicks in.
@buttlicker11605 жыл бұрын
Thanks I was actually looking to see if I had to pull the axles
@roadrash83342 жыл бұрын
good short vid. done with my build motor back in trying to remember how all the wiring harness went in. obvious stuff easy, its the lower sensors few plugs im lost on. have some left over plugs not sure where they go
@shoegod23117 жыл бұрын
Do you have videos of rebuilding the motor
@axemastersinc32698 жыл бұрын
I just got a 2005 Dodge Magnum RT. It is sweet.
@frankjones17498 жыл бұрын
what ever you do DO NOT LET IT RUN HOT.........EVER
@400smallblock7 жыл бұрын
frank jones Yup....it'll drop a valve seal and scorch a cylinder...ask me why/how I know this lol
@TheFabian4218 жыл бұрын
also, those front axles are a notorious PITA to get out. they tend to seize together. I've replaced entire front drive assemblies before because of it.
@gazagaza56012 жыл бұрын
That's a good infomation. How many days does it take to change?
@jameshutch49868 жыл бұрын
very good and informative video, surely helps seeing what's involved in such a task, especially since I'm planning on doing power upgrades soon to my 2005 magnum rt. Appreciate your work
@crazysexycool1809 ай бұрын
THANKS FOR WATCHING !!!! Please like share and subscribe, also check my other channel, Salem Taxi on YOU TUBE . Thanks.
@farnorth4x Жыл бұрын
Good advice to never put your arm under the motor. I lifted a motor with some pretty beefy but solid tow straps lent to me by a neighbor once while lifting a 500lb Mercedes diesel. I was desperate to lift the motor and adjust the motor mounts so instead of going to the store the next day and getting proper chains I used these. Strap broke and the falling engine would have taken my arm right off had I not moved it a few seconds before.
@justaskj6 жыл бұрын
I'm changing my motor in a 2011 grand cherokee, is there anything that have to do after the new motor is in with the electrical, no modifications or do I have to flash as they say the computer?
@siebert03098 жыл бұрын
Those aren't knock sensors in the valley of the engine under the intake manifold. Those are MDS solenoids. They are what makes the cylinder shut off when driving under normal conditions to save on gas.
@crazysexycool1808 жыл бұрын
+Brandon Siebert thanks
@MrTrip3ace8 жыл бұрын
+Brandon Siebert I was just about to make a comment saying that but you beat me to it XD
@gen3hemiextrememodernmuscl6536 жыл бұрын
I said the same thing those are mds plugs,you can get the fancy skanke metal ones
@rhurtadorh324 жыл бұрын
Gen 3 Hemi Extreme modern muscle i turned mines of with diablo i3 tune on my magnum
@SrtLv4x2 жыл бұрын
Thank you so much for this!
@captainobvious59935 жыл бұрын
What are those two metal lines running across the vally under the intake.. mine look pretty rusty
@tomrodgers84674 жыл бұрын
coolant lines
@pluguniv43577 жыл бұрын
You can't drop it out the bottom?
@demagchevy5 жыл бұрын
2 things, you removed the transmission and didn't take the torque converter bolts out? You have a lift and didnt drop the whole thing out from bottom? I'm hoping you did it the hard way to just show people who dont have a lift.
@crazysexycool18010 ай бұрын
the engine was locked up so no way to access the converter bolts, yes you can drop it but look at all the extra that need to be removed, not to mention the unit will still need to be lifted to be moved for the repair. Thank you please like, share, and subscribe, also please check out my other channel Salem Taxi, on KZbin for more material on a different level.
@alexamadeloff9956 ай бұрын
in my opinion its way easier to drop the motor and trans as one. lifting the body off.
@todd3090 Жыл бұрын
Nice video bro Thx
@sroc27664 жыл бұрын
Great video bro. Do more
@crazysexycool1803 жыл бұрын
Thanks for the visit please subscribe
@dustinangell14787 жыл бұрын
how long did it take you to pull the engine. i have an 06 magnum R/T that needs a new crankshaft from a spun rod bearing and i was needing to know how long it would take to get the motor in the heated garage. its cold outside lol
@crazysexycool1807 жыл бұрын
with the proper tools not long. only 4 bolts hold it to the frame. the rest is accessory connections. unbolt all and pull it out
@400smallblock7 жыл бұрын
Dustin Angell I pulled this engine in about 4 or 5 hours...taking time to label things and whatnot
@400smallblock7 жыл бұрын
in my own vehicle of course
@400smallblock7 жыл бұрын
in my own vehicle of course
@Ricky_Desch4 жыл бұрын
@@crazysexycool180 does this apply to 07 charge 5.7 rwd? Possible to drop it out the bottom?
@danr95847 жыл бұрын
Those engine mounts are very similar to Mercedes, and it also has a front sump oil pan. The Hemi would probably swap well into an older Benz. less fab than the ls swaps
@JoeyGarcia6 жыл бұрын
Well, I think the Hemi was designed during a time when Mercedes owned Chrysler, so that makes sense that they could be similar.
@ZTEKFORCE6 жыл бұрын
How did you disconnect the engine mounts? My engine mount bolts keeps spinning and there's no way to access it from the top so I'll have to remove the two side bolts where the mounts split on top! I have a 2006 300c AWD Hemi
@crazysexycool1806 жыл бұрын
remove the 2 bolts from under the frame that go into the bottom of motor mounts
@ZTEKFORCE6 жыл бұрын
I used the impact gun on one of the nuts and now the bolt is spinning but I was able to remove the side bolts and pull the engine out. Thank you. Great video!
@crazysexycool1806 жыл бұрын
when you replace the factory recommendation is to replace those mounting studs
@ZTEKFORCE6 жыл бұрын
Affirmative. I have damaged pistons, damaged cylinder heads, etc.. guess after fixing those I may as well replace the bolts. Never overheat the 5.7 HEMI engine or any engine. LOL. Thanks bud :)
@crazysexycool1806 жыл бұрын
for sure use NEW BOLTS, also if you have a good machine shop have the heads overhauled, they will last longer, also replace all the pistons . and the crank rods on the damaged pistons
@AjDaDon218 жыл бұрын
Have an 07 AWD and having trouble finding another AWD engine does it really matter if it come out of an AWD or a Rwd car?
@crazysexycool1808 жыл бұрын
No, Same motor. just different drivetrains.
@charlesbrewer3362 Жыл бұрын
Never leave the torque converter connected to the fly wheel
@dannyboy312899 жыл бұрын
I have everything except the front wheel stuff. does anyone know of a good resource for removal of the front gearing to remove the engine completely?
@crazysexycool1809 жыл бұрын
+Danny Bickel use a transmission jack. Remove the front cv axels first.
@marvinthomas59614 жыл бұрын
So they're not what you say they are those are MDS solenoid
@stanleyjones87497 жыл бұрын
yep I like this
@BobBuilder-om4rd7 жыл бұрын
when I do these, I just drop the whole thing out the bottom.
@egodeathplease5 жыл бұрын
i'm thinking the same thing. i have an awd magnum with the hemi. i have a car lift.
@ChrisCarpenter-d5e4 жыл бұрын
my brother has a 2006 chrysler 300 srt8. we,re putting headers on it but dont have a lift. talk about a nightmare
@franklindguccibelt62094 жыл бұрын
@@ChrisCarpenter-d5e I put SRT8 headers on my hemi and it was a pain in the ass
@johnchristopherrobert18396 жыл бұрын
If dodge owner are watching a dodge maintenance video. We don’t want to see a ford commercial
@rhurtadorh326 жыл бұрын
Do you knoe the reason for that hemi going out?
@crazysexycool1806 жыл бұрын
these engines are bad about dropping valve seats in the combustion chamber.
@rhurtadorh326 жыл бұрын
Artistry Photography when it drops the valve does it happen randomly?
@rhurtadorh326 жыл бұрын
Artistry Photography or at a certain milage?
@crazysexycool1806 жыл бұрын
random, seems to happen after an over heating event,
@Fringeless7 жыл бұрын
Hey Rufus I needed me a cole pak. Want trade a cole pak? I got a brain box for a phleetwud broham an a trottle body intake for a box car. Hey yo why yo gots a @6:34 some cadilac converters on yo dodge boy? Dats messed up. Bowtie an be alot cheeper than mopar shit anyway. Here in Houston, them hemi parts hard come by yo know mean?
@crazysexycool1807 жыл бұрын
catalytic converter not Cadillac converter, all cars are suppose to have these
@garrard_garage6 жыл бұрын
I think I just got cancer reading this comment
@bishop51667 жыл бұрын
now put a lsx in it.
@dinka45259 ай бұрын
did you drain the trans fluid?
@dansilva5016 жыл бұрын
Good job.. and great point on safety keeping body out the way..
@crazysexycool18010 ай бұрын
Thank you, please like, share, and subscribe, also check out my other channel Salem Taxi on KZbin
@JayMoungMUSIK7 жыл бұрын
do you have a How To for a DoDge 3.5
@BobBuilder-om4rd7 жыл бұрын
same way minus 2 cylinders.
@gearhead40056 жыл бұрын
Great video. Might be using this one day
@dgroove7049 Жыл бұрын
Which bolts did you remove from transmission bell housing? I'm doing a engine replacement on 14 charger 5.7 hemi can't get transmission bolts lined up
@crazysexycool18010 ай бұрын
all of them need to be removed when changing the motor
@bowchickawowwow62466 жыл бұрын
They are not. KNOCK SENSORS THEY ARE CALLED MDS MULTI DISPLACEMENT SOLENOID WHICH SHUTS OF 2 OF THE CYLINDERS ON THE HIGHWAY SO YOU CAN SACE GAS
@tomrodgers84674 жыл бұрын
not two but four cylinders
@davidbender29506 жыл бұрын
Do i need to support the trans
@nimbus30587 жыл бұрын
Did it bother anyone else that he was saying Cadillac convertor?
@crazysexycool1809 ай бұрын
Thank you, please like, share, and subscribe, also check out my other channel Salem Taxi on KZbin
@FreshKicks45457 жыл бұрын
nice
@jameshutch49867 жыл бұрын
awesome video tutorial, can definitely use this information. thank you.
@jesusr71746 жыл бұрын
Great video just one question my mechanic said he replaced my motor with one from 2011 it’s a 5.7 hemi mine was 2007 are the parts going to be the same for tuneups and what not also where do I find the cast number on the block so I know what year the motor came from thanks in advance
@dannyboy312899 жыл бұрын
Is this an awd hemi? If not, is there additional work that must be done?
@crazysexycool1809 жыл бұрын
+Danny Bickel No its rear wheel Drive. What type of additional work are you referring to? If you are Referring to the AWD version, you may need to remove the forward differential to reach other required bolts. around the transmission