I'm about to throw the entire bike hahahahhaa I'm still stuck hahahah
@BananaMobileGaming2 жыл бұрын
Nevermind I found a way like yours , I put a tape around it and then used drive RATCHET , it's out in 5secs and taking out the weight I use vice grip put a little clothe around it and then I hammer it out. Came out very quick no damage at all.
@serriteno12 жыл бұрын
@@BananaMobileGaming you saved me a headache the hammer method worked way faster.
@Chillzy2 жыл бұрын
How do I install the weights? I can't find anywhere that'll show me how to put the rubber parts on and properly get the weights in the handlebars.
@leandrolee76903 ай бұрын
first you have to remove the handle grip. there is a small two holes in the handle bar which is the lock of the handle bar end weight. then, you can pull out the bar end weight easily. you're doing in a wrong way.
@justinh2412 Жыл бұрын
Thanks for the video!! Although it's FAR EASIER to LEAVE the bar weight on the end. Roll back the handgrips so you can see the holes in the bars. Use a pointy object to rotate the clips sideways so the tabs go under the edges. Then spray with some light oil. Pull it out by the bar end. No drilling or anything needed. Can put it back in if needed. Hope that helps the next person!
@harshvishwakarma1890 Жыл бұрын
Thanks. I took my CB to get the handlebar replace and the mechanics didn't know this
@Skelly_777 Жыл бұрын
Thanks I was thinking about doing this but didn’t know if it would work,thanks for the confirmation
@karoslif98189 ай бұрын
I used that exact method on my Nc750x as I didn't want to destroy the tabs on the bar ends.
@stevensteel8617 Жыл бұрын
Thank you friend. I was looking at the Honda manual for the NC700/750 and the black and white images are really difficult to make out. Honda recommend removing the grip first so that, as another comment says, you can release and remove the retaining clip without doing any damage. One of my bar end weights snapped when I dropped the bike on black ice, so I may have a bit more fun trying to remove it, but your video has shown me exactly what I am looking at, so thank you.
@tocccapotato72292 жыл бұрын
Very informative , thank you
@G31S72 жыл бұрын
I removed mine with a regular Phillips head screwdriver. I put several layers of duct tape around the bar end only and used grips to grab it and applied pressure on the screw while unscrewing. Came loose with no issues.
@NYDStories2 жыл бұрын
Lucky you !
@LibanganTV_242 жыл бұрын
Thanks for the idea
@chrisdadigger1018 Жыл бұрын
They should not be this difficult this is ridiculous
@OneFreeMan1710 ай бұрын
Yeah I don’t know why manufacturers are so obsessed with making things so stupidly tight
@CrossfireVAL10 ай бұрын
@@OneFreeMan17 I think for safety reasons obviously but yeah, the bar ends are fucking stupid lol.
@_Progen_2 жыл бұрын
Thank you!
@nikhithhm Жыл бұрын
Title should have been "How NOT to Remove Honda Bar Ends and Weights" 😝
@NYDStories Жыл бұрын
True
@francisfe20647 ай бұрын
Remove grips, push spring clip in the hole to the side or get a mate to push it in and use the bar end and bolt as a slide hammer.
@rowelandres1394 ай бұрын
What's that for anyway?
@GrahamPinnegar6 ай бұрын
I’ve never had any issue removing the bar ends, to remove the weights I thread the bar end screw through a washer and then a 20mm socket and drawer it out like a cork from a wine bottle
@jangummi91645 ай бұрын
Just that,what do you with the clamps inside the bar?
@omnivore2220 Жыл бұрын
Excellent! (Except the part where you stripped the screw heads - that was foolish). Thank you for this video! I've seen some far more difficult methods for removing the internal portion, and this one is the best!
@deamonkhorne4777 Жыл бұрын
La meilleure c’est d’enfoncer avec un embout la bague sort de sont logement et ta juste à tirer après .
@chrisdadigger1018 Жыл бұрын
I can’t get mine loose either I gave up even my drill doesn’t have enough power
@chumchisk2 жыл бұрын
Stick a can of or use compressed air to take off the grips. Get under the rubber and blow.
@thelondonbiker Жыл бұрын
Hey - do you know if Yamaha is also gluing their handbars ends….having issues removing on an XSR 125cc
@NYDStories Жыл бұрын
I guess most of the brands do the same
@mikebenson80455 ай бұрын
Trying to remove the stock bar ends on the XSR125 was one of the worst experiences of my life. Had to get two mates to help me and it took all three of us. One of us pushing the clips in, one of us pulling the weight out, and the other holding the bike back the other way so it didn’t fall over. Took so much force it was ridiculous
@jkpisces Жыл бұрын
why do u have to remove the weights? wouldnt that cause more vibrations on your handle bar?
@NYDStories Жыл бұрын
mirrors don't fit with weights in. It worked out great for me, no vibrations.
@jeremyjohn1902 Жыл бұрын
Is there Any content on how to put them back in, I flipped my r3 and the weight came out. I don’t know how to put a new one in.
@NYDStories Жыл бұрын
Did not put them back, still riding without them
@jeremyjohn1902 Жыл бұрын
@@NYDStories oh that’s a bet, it’s j an r3 so I’ll ride it messed up j don’t know abt the safety but from what your saying it sounds safe enough to me
@owen_jdm7 ай бұрын
Honda just uses cheap hardware, I also stripped my bar end screws with a good quality screw driver. I had to drill the weight out with an 'easy out' bit. Just to have my throttle get stuck with my lever guards and made me drop the bike....I also tested the throttle before but its still got stuck. Luckily no major damage, just a couple of scratches
@Sking_285 ай бұрын
Same issue
@BMCMOTOUK Жыл бұрын
I removed my bar end weights within minutes simply by using an impact driver. One smack with the hammer and the screw came loose!
@akashkore1124 Жыл бұрын
How to remove broken screw inside the handle bar
@NYDStories Жыл бұрын
Try screw extractor
@christopherroblescatulong2074 Жыл бұрын
Salamat boss kala ko built in yun hehe
@user-yr7m22 жыл бұрын
What does the screw even do on the tip of the weight if you have to destroy it? I tried to srew it, nothing happens
@NYDStories2 жыл бұрын
It holds the weights in as well as the end of handlebar.
@grinding-gears2 жыл бұрын
It dosent have to be this way, Check out how I did it, its very easy to pull it out
@NYDStories2 жыл бұрын
Some are lucky :)
@mikebarbeau85692 ай бұрын
Tape then use impact sounds right...
@stevec47489 ай бұрын
It would have helped if you were turning the screw in the correct direction at the beginning. You were tightening not loosening. That's why you stripped the screw head.
@NYDStories8 ай бұрын
🤦♂️
@cb125frider42 жыл бұрын
What size screw did you use to pull it with? I've got some bar end's to go on mine and need to remove the factory bit to fit them
@NYDStories2 жыл бұрын
Nothing fancy a typical Philips screw.
@rossr3722 жыл бұрын
@@NYDStories It's not a 'typical Philips screw'. It is a JIS fastener.
@mikeh.9091 Жыл бұрын
Hi, thank you for this video! Well filmed, great! Could you tell me please the diameter of the inner handlebar weight? Keep on doing videos!
@NYDStories Жыл бұрын
Sorry mate, dont know that.
@narusam4108 Жыл бұрын
Too easy to remove, just remove the handle grip first then you can push the pin fron the tiny hole of the handle bar
@GINGERPRINCE19742 ай бұрын
I have to say this is not the way to do it use a puller method, which you can use with a deep sparkplug socket and the screw that comes with it, possible use a washer to if needed. But very easy to do.
@davincifpv39832 жыл бұрын
Sorry but why did you need to remove them in the first place? Any benefits? Cheers from New Zealand, keep the vids rolling out please and Kia Kaha!!
@NYDStories2 жыл бұрын
I did it to mount the bar end mirrors, but people add different mods to their handlebars.
@ihsanm12 жыл бұрын
My left weight on my 07 Honda cbr 1000rr fell out while riding. Now both handle bars vibrate. The left vibrates hard. Will heavy bar ends solve this issue even if the left handlebar is hollow?
@NYDStories2 жыл бұрын
Your bike have a different bar and position, Most likely you will need something like SATO bar ends
@knoxbom3274 Жыл бұрын
Are the bar weights necessary?
@NYDStories Жыл бұрын
Yes, they are used to reduce the vibration, but I ended up removing them, its a personal choice.
@knoxbom3274 Жыл бұрын
@@NYDStories didn't think of that....thank you
@user-ci2wd8xg4p Жыл бұрын
Better if you just pushed the weights instead of pulling it out. Weights has it's own purpose.
@1966johnnywayne2 жыл бұрын
Or...maybe start with the right tool. A poorly fitting Phillips socket wobbling around the Phillips screw??? A good quality JIS screwdriver would probably do the trick in a few seconds and save all of this headache.
@NYDStories2 жыл бұрын
Absolutely, but I worked with the tools I had, and most guys here do the same, I enjoyed the process and learnt from it
@rossr3722 жыл бұрын
1966johnnywayne Dead right!
@scottseedell2386 ай бұрын
Or even better, a cordless impact driver. It really is completely effortless.
@ajk66562 жыл бұрын
I wonder how Honda garages deal with it when they have to remove bar ends for whatever reason? Do they just drill the screw out and replace it? Lol
@horizonunlimitedph46302 жыл бұрын
I saw them using vise grips took them time to remove it also.
@schlubbyblubb7407 Жыл бұрын
man my weigts and this shit it so annoying im sitting since 2 hours on that crap and moved it only like 2 mm i never buy honda ever again, man i dont want to work like a real guy, I ONLY WANT THESE FUCKIN MIRRORS ONE THE END OF THE BAR i cant anymore but thx for the video hope i can do it soon
@StickerBao Жыл бұрын
🎉🎉🎉🎉🎉🎉
@s9enny Жыл бұрын
JIS screw driver simple
@roberiosolon2 ай бұрын
O vídeo mostra com destruir parafusos e clipes do contrapeso do guidão 😂😂😂😂
@Mayheezy5923 ай бұрын
Go elsewhere to watch how to remove bar end weights, he made this incredibly hard
@StanielBG4 ай бұрын
You are actually tightening them, not loosing them up. Try the other direction next time. :)
@einhundertfunfzig4919 Жыл бұрын
I could just pull mine out after losing the bolts
@NYDStories Жыл бұрын
Lucky you !
@rjlopez4594 Жыл бұрын
No no no. 🤭😮💨
@BillyBoblovesthedirt Жыл бұрын
I would have chucked it in the bin and put new bars on