I've watched hundreds of car videos and your the first I've ever seen to cover plates and not in post. That's very smart and a huge time saver.
@weeyins27412 жыл бұрын
I just pulled my badge off. I parked the truck in the sun for about 5 minutes and then started to peel it with a squeegee similar to the one in the video. Once I got it off there was a bunch of glue left behind - like in the video. I used the heat of the sun and folded it back into itself just using my fingers. It all ended up in a ball and that was it - perfect! No scratched paint. Thanks for the video!!!
@lorenwilkie40883 жыл бұрын
Sanding it will bond the adhesive really well. But it will make it harder to remove later on when you want to do it again.
@Marco-fi6gv3 жыл бұрын
It really isn't necessary.
@gssixgun2 жыл бұрын
Your vid was simple and straight forward, my rear emblem was pretty much the same and came of pretty easily. Getting the excess glue off was easier to just heat and roll with my fingers, gentle heat let me roll it without burning my fingers. Used just 91% alcohol to clean up the residue and replaced it WITHOUT sanding Thanks for your hints
@bmanh23554 жыл бұрын
All u need is heavy monofilament fishing line. Snake it behind the decal which is held on with 3m VHB tape. Then “saw” the line back and forth behind the decal. Then remove any remaining adhesive with wd40
@motoforlyfe4 жыл бұрын
Thanks for the tip! I'll give it a try on the next one.
@davemoen63234 жыл бұрын
Bman H - You are right on the money with the WD40! Works good and most people have it. Thanks!
@Mike-xh9kn2 жыл бұрын
If it were only that easy using fishing line😑
@martincraig20132 жыл бұрын
The tabs would cause a issue
@richardortiz87042 жыл бұрын
I hate Fords
@davidkapellas91973 жыл бұрын
Thank you, just bought a replacement emblem and had no idea how to put it on. Really helpful.
@carlosciruelos Жыл бұрын
Excellent video - well filmed, with clear explanation of each step. Links to each product that you purchased will make this any next project. Thank you!
@bobzak95082 жыл бұрын
Use some high tensile fishing line works too!!
@JabboRemus Жыл бұрын
Thanks for the video. Will be removing my emblems soon for obvious reasons. Can't afford to sell so this is next best thing.
@Zuleva_Official2 жыл бұрын
IPA and a rag works really well with getting the glue off as well if you want a cheaper option
@randyphelps30412 жыл бұрын
good one. I was able to do without heat gun. Thanks for the help! Appreciated!
@locooreo50224 жыл бұрын
Definitely going to replace my old emblems now !! Super helpful, thanks !!
@HtownKurt2 жыл бұрын
Good video, plan on changing my emblems to black on my Expedition. Thanks
@aserta5 жыл бұрын
You can also use lighter fluid to clean the residue. Also, if you can touch the inside of the skin where the emblem is, even with a stick, it would be recommended to push against it so that the metal grabs on better. Unsure how this tailgate is vs say a hatch back door.
@hydraulics3 жыл бұрын
When emblem off- spray a can of krown or fluid film into that tailgate if you live in the rust belt
@mikebortzel1756 ай бұрын
Much easier than I thought. Thanks! 3:35 p.m. 6/19
@nashguy2075 жыл бұрын
Good job buddy. You going to have that truck looking new again if you keep replacing everything. LOL A tip I have done in the past on some emblems and other things attached with 2 sided tape is dental floss to remove them kind of use it like a saw between the mounting surface and the tape it does a pretty good job. Have a great week!!!
@michaeldickmeyer4933 ай бұрын
Have the emblem that was ready to fall out, came off very easy. What is the glue/sticky stuff to put it back. My emblem is basically new, just need the backer. Saw 3m VHB tape?
@bertdowns52403 жыл бұрын
Don’t you worry - That Ford Glue is tuff stuff.
@jeremiahyoung59314 жыл бұрын
Hey thanks a lot for doing this video. I'm repainting my tailgate to get rid of some rust spots before they get too corrosive , and I was wondering what to do about the symbol. Now I see its not too bad to remove that I will order that. Thanks again appreciate it.
@noelturner28752 жыл бұрын
Hey thanks. About how far away did you hold your heat gun when you were melting the adhesive to remove the emblem.
@sussy120ms93 жыл бұрын
My guy you sound like Paul Walker, damn missed already, and thanks for the tutorial man
@frankiekupiec4762 Жыл бұрын
Hello, Thank You for the Video - Am very pleased with My Results...Love My Ford RANGER
@Obscamping3 жыл бұрын
Ford finally did something right with the new 2021 trucks, it’s on the front grill, they circled the problem
@epiclink112 жыл бұрын
I was looking at these emblems for sale on amazon and one of them uses screenshots from this video in their instructions lol
@JustinKruger3363 жыл бұрын
Cool I never knew it had screws, mine is a small old ranger with a small logo on the right side I dont think it has screws. At least ford uses good glue my logo is pretty worn out it's a 1997 but I'm gona wait till it completely fades or cracks or falls off lol btw your supposed to push pressure on any logo for at least 1 min and do not let it get wet for 48 hours the same for stickers.
@froglobster3 жыл бұрын
Thanks, didn’t know about pressure time nor 48 hours
@JustinKruger3363 жыл бұрын
@@froglobster they often have instructions and many websites you order stickers or Plastic hood ornaments from also say it on the website and lots of glues do to and paint.
@froglobster3 жыл бұрын
@@JustinKruger336 k thanks
@TheBradinator214 Жыл бұрын
Awesome, looking to do this on my Ford Ranger so this helped a lot? I'm also wanting to upgrade my tires and rims. What size do you have on yours?
@Arcturian1111 Жыл бұрын
Hi, My original one came off. What do I use (glue etc) to adhere it back on again.
@colinmacdonald76033 жыл бұрын
I have a faded plate just like yours and a picked up a replacement on marketplace for cheap ...downside it doesn't have the sticky plate ... can I use the old logo inner plastic adhere plate with the new logo cover i have and glue it ?? any advice would be appreciated
@UberKrispy2 жыл бұрын
wonder if a hairdryer would work as good as the heat gun.
@dwwmoon2 жыл бұрын
I used a hair dryer on my front emblem. Would not sand the paint. Use a good paint compound then alcohol it.
@jonas4jonas4 Жыл бұрын
Fishing line works well to get the emblem off
@chrism74113 жыл бұрын
The sanding isn’t necessary at all. But looks good
@Redneck_Ed3 жыл бұрын
Yeah, I thought the same thing. That old adhesive was stuck to the tailgate way better than to the emblem. So if sanding increases adhesion to the tailgate, your weak point is still on the emblem side. I pulled mu emblem off with no heat either. Just pulled right off.
@chrism74113 жыл бұрын
@@Redneck_Ed yessir mine didn’t need heat either
@johnmac47694 жыл бұрын
Good job, looks great. Need to do the same to my F250
@ruthglass31032 жыл бұрын
How do you put the tin emblem back in to the casing. But just fell out
@gw53093 жыл бұрын
Great video. Denatured Alcohol is my go to goo and glue cleaner.
@froglobster3 жыл бұрын
What is denatured? So you get it from parts store or hardware?
@EddieMaxwell-hb6cp Жыл бұрын
Where to get emblems
@Michael-gs5ex2 жыл бұрын
Is it the same way for a front emblem?
@anonymousnoname18893 жыл бұрын
Fantastic job/ video... end result is fabulous
@angelfigueroa14674 жыл бұрын
Thank you for the lesson, great job!
@lori47823 жыл бұрын
So can I do this also to the side Emblems? Yours is the first video where you did not take nothing apart, like some videos took the tailgate apart to take emblem off.
@regsparkes65075 жыл бұрын
It's good to see how to remove and replace these emblems,..Thanks!
@lewcore3 жыл бұрын
great job friend!
@Adam-gi1yl Жыл бұрын
Nice video 📹 👍
@Kyle-mf5kd4 жыл бұрын
If you don’t mind telling, where can I find those fender flares?
@weeyins27412 жыл бұрын
FYI: Link to emblem on amazon doesn't work
@christinedaulizio59943 жыл бұрын
this vidoe was very helpfull. Tks.
@stevensimons.soss13 жыл бұрын
Brilliant vidio, many thanks ive just changed mine 😁
@adriansolis27872 жыл бұрын
NICE JOB....FORD TOUGH!!
@blackscotydog3 жыл бұрын
Thanks for this I have the same truck!! even same color.
@djchromick5464 Жыл бұрын
👍 thank for the video
@elcuby2 жыл бұрын
The link is not working 😩
@28daballa3 жыл бұрын
Are the new badges plastic or aluminum?
@philippittman66642 жыл бұрын
Emblems link not available, anyone know of sure replacement part?
@MoisesAlducinLinthwaite3 жыл бұрын
There was no need sanding area!
@TrentonWilliams342506034 жыл бұрын
Gonna try it today
@aptopowerup4 жыл бұрын
what kind of shell do you have on your ranger?
@criticalnewstvcriticalanal24954 жыл бұрын
Well done, thanks, i will try it tomorrow
@fawnbutler91583 жыл бұрын
EXCELLENT THANK YOU GOD BLESS YOU 🙌 🙏
@BryceCzirr-jz7ju8 ай бұрын
Just use fishing wire and floss it up and down until it comes off, and rubbing alcohol to clean. You are making this way harder than it needs to be.
@daddone923 жыл бұрын
Secondo te su la Kuga è ugualmente attaccato ..?!
@thatalaskaguy3 жыл бұрын
I refuse to replace mine. I like my Ford truck but they should provide replacement emblems for free.
@krisanderson43524 жыл бұрын
Do u think since it's so cold out that it may have been a good idea to heat the surface and the emblem ???
@autobotavengerfireballxl53393 жыл бұрын
minus the sanding step and your good bud
@JustMike27913 жыл бұрын
Just asking, why cover the license plate? No one besides a cop has access to the ANY of the information on a license plate. I have an '06 F150 that I'm looking for the gen of F150 that uses the 9" oval that is three pieces so I can take it apart and paint it. I'm murdering the truck except for some accent pieces
@chriholt5 жыл бұрын
Looks good!
@bologna30484 жыл бұрын
Wouldn't Goo-gone be safer instead of lacquer thinner? That stuff is great when you need it.
@motoforlyfe4 жыл бұрын
This was some tough stuff, not sure if goo-gone would have cut it!
@rpfleger25602 жыл бұрын
I used goo-gone, but still had to scrape a lot. Overall, the glue removal took about 10 minutes. The key to the removal of the emblem was most definitely the heat gun. I first tried without it, and then watched this video. The heat gun was like $25 and worked like magic!
@qwertshadow3 жыл бұрын
but it still says Ford..
@SiemReap20124 жыл бұрын
I went on to your website. Couldn't find this part.... help?
@motoforlyfe4 жыл бұрын
Thanks for the heads up! Here's a new link: amzn.to/3lehPtF
@hydraulics3 жыл бұрын
@@motoforlyfe that link dead too now. Got a part #? Thanks for the video
@marcsongaudin84294 жыл бұрын
What about I don't have a heat gun?
@AJannace114 жыл бұрын
Fishing line works well too
@froglobster4 жыл бұрын
I did with hair dryer
@ancientheart25324 жыл бұрын
Scotchbrite pad would be better I think.
@DriveShaftDrew5 жыл бұрын
thumbs up shared looking good great job
@motoforlyfe5 жыл бұрын
Thanks Drew!
@yogirlbreea59893 жыл бұрын
The emblem came off but the rest of it didn’t. 😭😭
@jameskramer99644 жыл бұрын
Hey bud you said you were going to put the email address for the Ford symbols I don't see it any chance you can send it to me or put it on here.
@motoforlyfe4 жыл бұрын
Here you go! amzn.to/2LFHkEm
@connorsimons28010 ай бұрын
Job well done brother, I was just gonna try to rip her off lmfao.
@quentinh43164 жыл бұрын
Awesome
@thisguy89674 жыл бұрын
👏🏽👏🏽👏🏽👍🏽
@ancientheart25323 жыл бұрын
Tape it off!
@seanlamonte1402Ай бұрын
Why is emblem so cheap and fake?
@alienpick14 жыл бұрын
Jesus Christ is Lord ✝️ Maranatha
@kevinwalsh2513 Жыл бұрын
$15 for 2 Amazon, you bought fake rubbish that won’t last. Ford uk sell for £29 each. You’ll be changing again soon. 😂
@mrkillemall994 жыл бұрын
Do you know if it is the same process for the emblem with the back up cam on it?