How to Remove Sealed Trailer Lights

Рет қаралды 58,659

Күн бұрын

Пікірлер: 35

@brennanrjohn 4 жыл бұрын

Nice job! Very realistic because we know not everything goes smooth the first time so you worked through it and came up with the solution.

@markkeller8915 Жыл бұрын

good job!! I came here for help and got the info i was looking for. I don't use dilectric grease on metal connectors, it is the insulator to spark plug boots, so spark energy doesn't waste on the porcesling if it is dirty. for electrical connection to be improved,this would do the opposite, yes it will keep corrosion from happening. There are two products for connection improvement, either Ox-gard, or Truk-lite. Ox-gard common at Home depot. It has conductive grit in the grease to improve electrical connection. Thanks again for your help getting my trailer lites out.

@mikeartell4922 3 ай бұрын

Just a thought, as long as the rubber gasket is still somewhat soft and playable, if you can reach under and around to the backside of the light you can just push the old light out from the back.

@barefootbob1269 Ай бұрын

A lot of trailers are a sealed cavity and you cant get to the back of the light.

@TJHSLLC 2 ай бұрын

Thanks! I was having trouble on mine and your video saved the day and saved my seal!! Thanks 😊

@Drew-in-NoDak 4 жыл бұрын

pro tip, clean out the rubber grommet with hot soapy water and the light will go in way better. especially in the extreme cold

@barefootbob1269 Ай бұрын

Yup I spray mine with windex won't freeze as quick in the cold and then evaporates.

@arthurmur5774 10 ай бұрын

Thank you! It kinda made me happy that you had a bit of trouble there at the beginning to pulling it out. Made me feel better about my self and my struggle

@mikeartell4922 3 ай бұрын

Just a thought, as long as the rubber gasket is still somewhat soft and playable, if you can reach under and around to the backside of the light you can just push the old light out from the back.

@barefootbob1269 Ай бұрын

It is so much easier pushing the light in push from an end. Once pushed thru you can remove the rubber gasket and bring the light back thru the now large hole.

@davidmorad4405 5 ай бұрын

Thanks for posting this video. Saved me some $$$!

@ronlitz9055 7 ай бұрын

Exactly what I was looking for, tx 4 posting.

@jimpulcine9925 9 ай бұрын

You're the man. Great video. Now I'll try it on my trailer. Thanks

@pv6751 2 жыл бұрын

Check the new bulb works first. Make sure it’s not another problem. But good video.

@joeturcotte2810 2 жыл бұрын

Very nice but how do you change the light bulb inside?

@danielwilson7572 2 жыл бұрын

These are LED based units. Similar units that use replaceable bulbs should have some screws to access once you get the unit out.

@kimbcrouch1 Жыл бұрын

Thank you very much for this!

@nickbayer7847 2 жыл бұрын

Thanks 🤠🤠

@petew03 7 ай бұрын

Amen thx for posting the video

@normanmoore8670 3 жыл бұрын

Thank you!👍👍👍

@JasonSmith-utube 3 жыл бұрын

This is the WRONG way to remove these lights. Push the light, then lift up the edge of the rubber gasket and the entire thing pushes thru.

@danielwilson7572 2 жыл бұрын

We will have to try that next time. Thanks for the tip.

@WhodatnTx Жыл бұрын

I’ve ran into a couple of cases where there is a solid plate right behind the lights. In those cases the way he demonstrated is the only way.

@ericr5561 7 ай бұрын

Thanks for the video

@Gallomimia Жыл бұрын

It sure isn’t that easy for me. The light is destroyed and I still haven’t got it out. The previous time I removed it, the grommet was destroyed. Sure would like to be able to get them out that easily.