how to repair 2mm led module in 2 minutes

tutorial video about P2.6 mm LED module repair.
www.danielsrepair.com [e-mail]
cell# [phone]
Taken by Daniel's Repair based on the practice and experience from 4400 pieces of LED modules repair
It is also applicable to P0.9mm, 1.2mm,1.5mm,1.9mm,2.5mm,3.9mm LED module repair.

[@hamim2.s3hy]

what is the temperature of Air Heat gun?

[@richardenriqueaguilarbasti3243]

What kind of paste do you use to keep the LED glued to the plate and not move with the hot air from the heat gun?

[@nizarm.alhazmi8911]

I like your way of explanation to how to fix the problem..!! So I have a problem in my led display screen module..!! I have around 6 meters long display screen and consists of two lines of led blocks... The problem is that the (upper line) which consists of around 15 led blocks is the whole blocks are always lit up, while the (lower line) is working and displaying normal which shows up the lower half of the words and numbers only...!? So please if understand my explanation, tell me how to fix this problem..?? Thank you so much...❤

[@patrickhavlicek2128]

What temperature do you use on heat gun

[@sampledfuture]

The real question is, why were those pixels on wrong in the first place? That didn't look like they were damaged by any impact they looked like someone tried and failed to repair them. Im not that lucky because most of the pixels I have been repairing over the last 8 years have had the traces pulled off, so I need to run wire or put on new circuit paper. Good video though keep it up.

[@danielsledrepairservicellc9347]

Thank u mike, they were damaged and I started the recording after I putting circuit paper. lol

[@jorgenava3746]

Hello, good day, I have been looking for where I can get the circuit paper for 2121 smd diodes, which are from an absen P2.5 lite panel, could you orient me where I can get it? Thank you

[@elizernarcavillegasjr2859]

What is the reasons for faulty LEDs I encountered this issue I test RGB color when it comes red was okay but blue color there are some dots no color and the same the green color but if white display the no color of dots comes a yellow color

[@djjavierpr]

Hello, i have a few cabinets that have like 10-15 led stock on the same color, when i heat it up like on the video they work just fine, but when it start to cool down the led go back to the color it was stuck before, any ideas on how may i fix this problem? Thanks!

[@vickyganbakoled8348]

Dip some tin soldering paste it and try again 😊

[@note2tee]

A cracked solder joint which expand on heat and make contact and break contact when cool or the led is bad the bond wire inside the led could have been floating

[@axpx79]

hello friend what do you wear to protect your eyes? of the light of the leds on

[@edwardcarcallas3708]

Wow galing nyo sir

[@noworktodo7118]

I have moisture damaged panels how to remove moisture from them???

[@saixu7815]

It’s really helpful.👍👍

[@tanerkorkmaz6950]

faydalı bir video teşekkürler

[@vishan02]

What's the temperature to use? I'm trying to fix 2.9 leds.

[@mrrandom681]

I have a p4 led module mobile truck and I have a lot of rectangular spots throughout my whole truck. If I apply heat will they go away ?

[@danielsledrepairservicellc9347]

Hi , You can send me some photos and then I will know how to repair it. my email address is: [e-mail]

[@mrrandom681]

@@danielsledrepairservicellc9347 thank you! I emailed you!

[@alajmee]

dear... no need to take off the light led and no change ?

[@MochaMan]

will this work on flexible addressable led matrix...only one light in matrix keeps off if any blue color, red and green and yellow works, white shows yellow

[@rainbowaudiovisual]

Hi I have 3.91 LED. Pink patches are coming in LED. Any solution for this.

[@pavanvideovision]

hi daniel i have a p4.8 pitch screen some module lost a soldering pads what we do

[@lildel2669]

nice thank you awesome video 👍🏼😊

[@dadsonsfoodblog5039]

What heat gun model do you use?

[@alajmee]

dear.. o have in door 3.9 gloshine.. really no need change led light?

[@arieawp]

What is the temperature you use sir? Thanks for the answer 😀

[@danielsledrepairservicellc9347]

the temperature I used in the demo video is 350 degrees Celsius.

[@showvirtualrd8377]

@@danielsledrepairservicellc9347 WHAT KIND OF LED CAN YOU WORK WITH AT THAT TEMPERATURE?

[@samsonfpv8902]

Temperature of heat gun please

[@賢者之屎]

可以教我怎麼修嗎?或者是有中文字幕版本

[@mdaslamknl]

Excellent Where can i buy led Thanks

[@vipulsharma5353]

What will be the reason for these faulty LED's ?

[@ledmalith2421]

good job ''LED Malith''

[@gregdacumos7432]

Hello sir can you help me out i wanna learn to repair our led modules, im operating a ledwall in Philippines and i wanna learn also too repair so i could replace any damages on our ledwa, btw our ledwall is P3.9

[@TONIWIDI]

hello daniel, where you buy the LED, for replace it? Can you answer my question by website link where you buy it?

[@danielsledrepairservicellc9347]

Usually I ask the factory to give to me or extract from damaged modules.

[@abecoulter18]

Why have you left the power on

[@danielsledrepairservicellc9347]

Because we can see directly if the new pixels are well attached to PCB or not.

[@rudyhartono8336]

Dear Sir,.. any idea how to fix a strip ( green, blue or red color ) on led wall. I have try to change the ic driver and checking on LED Chip as well but the problem still same.. sometimes the problem come up randomly. thanks

[@danielsledrepairservicellc9347]

Hi,Rudy, Thanks for your inquiry. May I know which country are you from?

[@rudyhartono8336]

@@danielsledrepairservicellc9347 indonesia..

[@maritzasaucedo8572]

Hey Daniel do you offer a course For LED repair in Southern California

[@vorsondigital4783]

are you in paksitan

[@kashinathbaluragi7925]

Hey. ..hi .. I'm also from led repairing team.. can u tell me how u repair p1.56 ..Bcoz. I had done repairing minimum pixel pitch p2

[@danielsledrepairservicellc9347]

thanks for your attention! I will upload more videos about P1.5 and P1.2, P0.9 repair tutorial as soon as possible.

[@danielsledrepairservicellc9347]

kzbin.info/www/bejne/oYnFm4Cpacx-fq8 this is the link of repairing 1.2mm

[@ramkrishan922]

Please told me how to remove the moisture 6MM

[@danielsledrepairservicellc9347]

keep the LED screen working with 100% brightness in a high temperature environment

[@smirza508]

@@danielsledrepairservicellc9347 how many in white balance

[@gur316]

Where to buy the LEDs link please

[@danielsledrepairservicellc9347]

which brand and size of LEDs? I can sell to you .

[@gcamarena120]

by any chance do you know where I can find sw2.5-1515 circuit paper?

[@alnoorsmdadvertisingscreen7908]

Hello You are from china?

[@danielsledrepairservicellc9347]

Yes,I am.

[@biyerbarii]

Can I get your WeChat

[@danielsledrepairservicellc9347]

leddaniel

[@nikolaradakovic5432]

Liar

[@aNewJesus]

I wouldn't want to send you my LED tiles tbh. This is a bodge not a repair

[@danielsledrepairservicellc9347]

Thanks for your watching and message!

[@aNewJesus]

Yeah! Maybe something for on show site but I wouldn't want to charge a client to do this

[@danielsledrepairservicellc9347]

@@aNewJesus check this video kzbin.info/www/bejne/oKSadYyGqseLeJY

[@KIVAKILOKUDO]

Daniel good day, do you sell that tool? what is the name to the tooll and what is the price, greetings

[@johnerickvidarte7715]

Hola cómo estás cuál es tu WhatsApp

[@ak4575]

Hi sir.. Hinde