How to Repair and Clean Snow Foam Lance

if your snow foam lance doesn't produce a thick foam anymore, or it starts to leaking, you might want to watch this..
also remember to rinse the foam lance after each use,
so you won't have soap scum build up that will be blocking the gauze in the future.
Online Shop Ane Gan :
Shopee : bit.ly/2Z4QEWP
Tokopedia : bit.ly/2wxGtxy
Bukalapak : bit.ly/2Mm5PcC
----------------------------------------------------------------------------------------
EBAY. com
Nilfisk C110 : goo.gl/LbQuyA
Autobrite Foam Lance : goo.gl/2WTMiJ
i6/Sam's Foam Lance : goo.gl/pLdFbA
MJJC Foam Lance : goo.gl/Zd3Hb3
----------------------------------------------------------------------------------------
EBAY UK
Nilfisk C110 : goo.gl/Y7cR1a
Autobrite Foam Lance : goo.gl/4hLEUc
i6/Sam's Foam Lance : goo.gl/EGbKO3
----------------------------------------------------------------------------------------
AMAZON U.S
Caustic Soda : amzn.to/2eXh2M5
Vinegar : amzn.to/2eiS7E4
Bench Vise : amzn.to/2f8NdZk
Teflon Tape : amzn.to/2e9CKuu
Rubber Foam Sheet : amzn.to/2e9Gig9
Nilfisk C110 : amzn.to/2cRD1HH
MjjC Foam Lance : amzn.to/2cTnrac
other Foam Lance : amzn.to/2fI2W0v
----------------------------------------------------------------------------------------
AMAZON U.K
Caustic Soda : amzn.to/2eQgmdF
Vinegar : amzn.to/2eXmNZW
Bench Vise : amzn.to/2eQjsyg
Teflon Tape : amzn.to/2eXnHFK
Rubber Foam Sheet : amzn.to/2eQjSoc
Nilfisk C110 : amzn.to/2cthFwc
Autobrite foam lance : amzn.to/2eJNbFf
MjjC Foam Lance : amzn.to/2cmAfue
----------------------------------------------------------------------------------------
TOKO ONLINE SHOP ALFIE DETAILING
---------------------------------------
www.bukalapak....
---------------------------------------
shopee.co.id/a...
---------------------------------------
www.tokopedia....
FOLLOW INSTAGRAM
@teuku_alfie
#alfiedetailing #autodetailing #carcare
Music by Tobu
/ tobuofficial

[@alfierenadhie]

Online Shop Ane Gan : Shopee : bit.ly/2Z4QEWP Tokopedia : bit.ly/2wxGtxy Bukalapak : bit.ly/2Mm5PcC

[@austprodriver]

Mate, this is an outstanding video. I finally cleaned my foaming cannon, by using your methods shown here. 10 out of 10. Thank you very much. Ace!

[@alvinlee5642]

great job bro alfie. i believe this is the only tutorial video on how to clean a foam lance on youtube. if not, this must be the best one!

[@ro63rto]

Far safer and a lot cheaper is to use citric acid powder. The stuff you can buy in Asian stores. I think it's mainly used for pickling but I use it to descale my kettle also. Just boil a kettle full of water and add a packet of the powder into a large mug. Costs 80 UK pennies. 👍

[@Streaty1984]

Sorted mine out nicely, wasn’t foaming at all anymore. Took it apart & everything looked clean including the gauze but leaving it to soak over night sorted it right out 👍🏻

[@theblade66]

Thats a great video, I'll save that. I usually spray fresh water after use. But I don't store it upside down. It goes back on the bottle. Never an issue with it. I think rinsing it is very important after each use 👍

[@aprilr4274]

*I haven't used it yet, however, this pressure washer replacement gun offers greater spray flexibility over the standard sprayer gun that came with my pressure washer originally.*

[@efthimios]

I didnt even buy a MTM yet, and i watched this because its so well done. Great job.

[@eirewill6443]

1:55 in the video for me it’s impossible to get that piece off the snow foam lance

[@samiullahzahid2091]

Thanks a lot you have saved me money and time, yesterday i watched your video and fixed my mjjc classic cannon. 😊

[@rottenblaze6717]

Worked first time, thanks for this video. I will certainly recommend this to fellow detailers.

[@darvaish4552]

Alfie you are a star mate, thanks. you just saved me from buying a new one.

[@MikeLightning]

what the heck this guy in Indonesia has made in the USA parts... I live in the USA and can barely find anything made in the USA xD

[@JohnWilson-qf5tk]

Made in Italy they are.

[@O_Prim3]

You shouldn't use teflon tape if you have an o-ring seal already. You could introduce a leak.

[@O_Prim3]

Alfie Renadhy in this case the O-ring is what's providing the seal so if you tape over it there is a chance the water can flow around it. It's probably fine to leave it as is, but when you already have a gasket or an o ring you don't need tape. It's odd they say to tape it.

[@waytoohip4u]

I would say it's ok to put the Teflon tape on the threaded section only, carefully of course so not to contact any part of the o-ring.

[@fou-dou]

Under normal circumstances, we DO NOT have to place teflon tape on the O-Ring connections. However, it is common to use teflon tape when the O-Ring is aged and worn. The ideal solution would be to change the O-Ring with new ones every time. There are also special lubricants on the market that help O-Rings to remain in good condition.

[@AndyCheah0625]

Is there a way I can tighten the feel of the top foam adjustment knob?

[@mic400uk]

thanks for the helpful video, I don't have a vice and do t know why my pa lance doesn't work. I'm just going to buy a £20 lance of Amazon

[@kvn2266]

You're the man brother, thank you for another great video 👌 I wonder if one day you can do a video comparing this unit to the MTM Hydro 14.5001 PF22 Professional Foam Cannon. Cheers from NYC!

[@fou-dou]

Under normal circumstances, we DO NOT have to place teflon tape on the O-Ring connections. However, it is common to use teflon tape when the O-Ring is aged and worn. The ideal solution would be to change the O-Ring with new ones every time. There are also special lubricants on the market that help O-Rings to remain in good condition. Beyond that, it's a great video, like many other videos on your channel. Well done! Keep going.

[@fou-dou]

@@alfierenadhie In the plumbing (this is my profession), we use a kind of fat. But here, this is not drinking water, so the silicone grease is ok. I also usually use teflon tape for precautionary purposes. After all, it will never hurt the tool. *I wish I had discovered your videos with MJJC foam lance, before i bought the FJ6 karcher😌

[@jokiejokes]

It Just Works

[@johncheng9507]

Very Clear direction, I like it

[@richy320]

15x ive watched ur video id think i know by memory how to do it but not yet cleaned up my cannon for 7+ years now

[@35bigbri]

took mine apart uesd my air compressor to clean and works great again :-)

[@kevinlu3911]

Hi Alfie. Great easy to follow video. What sort of concentration ratio do you use for the caustic soda solution? My tub says to Dissolve 55g (2 tablespoons) of caustic soda in 1 litre of COLD water for use as drain cleaning. Should i use the same dosage?

[@paulwharton1850]

Excellent video - Thank you, I learnt a lot This will help me a lot.

[@CandraSangkono]

mine , pin got rusted and hard to push how to release the pin?

[@tarassu]

Also apply some silicone grease to the o-rings.

[@sunderachari3693]

Thank you brother your method is hundred percent good my problem SOL thank you very much

[@jokerfleckcast3196]

is a 1.1mm orifice better for a nilfisk c110?

[@srinivasl.sutrawe1777]

I question bro if I use it weekly once then how to maintain it I mean after how many weeks do I clean it by opening it or is it ok after shampoo work only spray water from bucket and ok ? Thanks in advance. Reply quickly.😜😎

[@ssingh2525]

Great guide, thanks Alfie. Anyone know where a set of replacement o-rings can be sourced?

[@GinoBo]

Any luck finding the correct o-rings ? There are tree different sizes on the foam cannon. Very difficult too find the wright ones.

[@arapaimagold8088]

Try electric tools shop that's selling air compressor.

[@markbirrell5768]

thanks thought I was going to have to buy another great instructions very clear sorted now

[@YaseerKMDGames]

5:13 كأني أسمع صوت آذان ولا :)

[@gandiutomo4337]

Mas punya saya mjjc foam lance baru beli kenapa tidak bisa berbusa spt yang diharapkan alias masih encer padahal takaran dilution sdh benar.. Apa perlu ganti mesh filter atau nozzle yg lebih kecil lagi?? High pressure washer saya 120 bar Karcher

[@ptrhartono]

Good Tips at the end of the video.. Bravo!

[@rakeanwachyu7455]

Cool, Keren Videonya, sangat bermanfaat buat nubie yang baru mau belajar car care nih....Thanks!

[@arielbustamante9333]

Great how to video. Thanks Alfie

[@paulj5129]

Brilliant video.

[@hamzahishak1032]

Alfie, di mana saya boleh dapatkan Nozzel 1.1mm untuk Autobrite seperti yg anda gunakan itu

[@SK-1689]

Great video!

[@lentilsouper]

I tried this but my Lance just froths out on the floor

[@carlmistry]

Fantastic video

[@nicholasvesakha1644]

Kak Alfie beli high pressure power wsahernya dimana yah ?

[@mimmigranaas3440]

Excellent tutorial!

[@alexwhite2247]

Great video, thank you

[@ridhobaihaqi144]

mas, kalau untuk MJJC juga sama perawatannya??

[@igbsecurity]

Great tutorial thanks

[@dereksteele1866]

very good thanks dee

[@darbats]

Nice.... how many time you will clean the foam cannon for a daily carwash business?

[@robertmcgruder554]

wyn after every use rinse with water. Fill foam cannon with Just water

[@rodrigofreitas7949]

Peças de reposição onde comprar

[@geraldcamarillo2939]

Man you go all out!

[@nileshramchandrapatil1482]

TySm sir best video n helpful 💯🥰

[@PadmaDorjee]

that was super helpful

[@moneymaker3203]

my snowfoam only produce water, where is the problem?

[@petecurran3995]

Nice style, fella! 👍🏻

[@youngandi83]

cairan pertama apa namanya ya?, dan cairan untuk bilasnya.. pake cuka ya gan?

[@alex-66740]

Thank you so much for the video, he help me a lot too !

[@tariks6167]

I ordered the foam cannon from chemical guys, but it sprays horizontaly not verticaly. So can change it somehow?

[@tariks6167]

Alfie Renadhy better I leave it as it is ... but I think its better it sprays verticaly ...

[@irmapapao4684]

ub

[@nevis1344]

Very helpful and well made. Thank you.

[@mopanutube]

Mas beli nozzle tip nya dimana dan ukurannya 1.1 atau1.25 mm. Terimakasih

[@alfierenadhie]

Ga ada jual kalo autobrite gan

[@dimassatrionugroho6651]

tinggal bikin video cara bersihin engine bay

[@ibnurasedi9136]

Very nice video bro...very detail...done subs

[@DaiLoo888]

Gan itu bersihinya harus rutin tiap bbrp kali pemakaian atau kalo pas ada keluhan aja gan? Emang pake shock itu ga ngerusak brass dan mesh filternya gan? Agan sampe sekarang pernah ganti sparepartnya foam lance ga gan?

[@DaiLoo888]

@@alfierenadhie tq gan info nya

[@sun9912]

Good job bro

[@MrLiquerub]

is this foam lance good for nilfisk c-130?

[@alfierenadhie]

The best!

[@stalinclaudio]

Please.. How to maintain snow foam mjjc..

[@alfierenadhie]

See at the end of video

[@stalinclaudio]

Thank’s

[@danielng9138]

bro itu autobrite beli di ebay. pas nyampe di indonya kena urusan cukai lagi nga? Makasih

[@danielng9138]

ok deh.. itu biasa dikirim lewat pos yah gan? saya test coba beli lance juga ^^.

[@cesarcaballero6440]

Muy bueno el canal ...

[@alexavramescu]

In can't wait to arive ! NIce product!

[@ryanbrandt3374]

Thanks for the vid

[@familymemories462]

fantastic

[@Lazyshooter1]

Bawaan autobrite pake orifice 1.25 ato 1.1 bro??

[@UaeDelta]

@@alfierenadhie I dont understand, but yes mjjc sells the orifice, its works on Autobrite foamlance. Usually it comes with 1.25mm but if your pressure washer is weak use 1.1mm more foam.

[@andikarachman5805]

How much your lance ?

[@HappyDaysNI]

Thanks. Just repaired mine too!

[@sharky09000]

Thanks fof the info m8 🖒

[@mangjay7573]

Kereen videonya

[@user-xn1op6fw2o]

Ну и где пена??????? Может он нерабочий и пены не даёт.

[@firoalhadi9010]

3:56 itu pakai sealtape kran air??

[@calonsulitditemukan6917]

Lah emang

[@Eduardoramundo]

👍👍

[@pencilme1n]

So you need a weekend and a degree in engineering to clean a badly designed snow foam. The filter should be easily removable.

[@weaverdetails4747]

I have a 20dollar amazon cannon that I will put up against anyone’s mtm. On that note I will just purchase another one

[@triciasticca8418]

Thanks for the great idea........ jus buy a new one!

[@5150roc]

With what you spend on getting it clean, not to mention your time, one can buy a new one for $15 bucks.

[@uwot9021]

His one can cost up to 60 AUD

Michael L ... Yes, fuck the planet and crush the wallet -.-

[@germanshepherd13]

totally agree. of course the huggers won't like that

[@enggaradinugroho6200]

Nice video. Too many bokeh for me

[@irmapapao4684]

raaafu8

[@CandraSangkono]

My pin do hard to remove any idea?

[@adielaryanto]

Very helpful, thank you very much

[@trevornelmes9331]

Great video. Thanks.

[@speedcanada1]

Excellent video!!!!!