*This battery reconditioning program exceeded my presumptions. It worked on any drill battery, several AA and AAA batteries, **batery.repair** and any camera battery. The steps are simple and the act itself is exciting to do. No matter what type of battery you`ve got, it is sure to function again!*
@wowtrailers5329 Жыл бұрын
Making use of the kzbin.infoUgkxcJ22tnHH9l1vjdIdEIG27iOG55P7LXI8 reconditioning plan, I just saved 2 auto batteries from being completely junked. The guides were very simple to follow. I wish I would have found this years ago! You may use the guide to recondition any battery type
@johncrosley13 жыл бұрын
We used this method in the army in the 1960’s. We had two special moulds for pos and neg, so this was an officially accepted field repair. You are not short circuiting the battery. The resistance of the carbon rod causes it to glow red. If it was a dead short the rod wouldn’t heat up (Basic Ohms Law) and you would damage the battery. A vehicle battery can easily handle the current required to heat the rod to red heat for the time required. We didn’t strike an arc but buried the red hot rod into the molten lead while feeding in bar solder. Obviously the skill was in not melting the entire post. I only used this method twice ( once on my own car to save the cost of a new battery) but it was successful both times. You can see from the gauge of wire used in the video that the current isn’t excessive.
@christopherleubner66333 жыл бұрын
You can harvest one of those carbon rods from dollar tree d size batteries. The AA size will get white hot.
@johncrosley13 жыл бұрын
@@christopherleubner6633 Yes, I used the carbon rod from a D cell.
@christopherleubner66333 жыл бұрын
A soda pop can, scissors to cut to a strip battery terminal size, some sandpaper or wire brush to prep the lug. A small container to melt lead in. A bit of flux if desired, usually not needed. Cast and let solidify. Remove aluminum sand if you want to, and enjoy your new lug.🤓
@thunderfall2eg9244 жыл бұрын
Buen video. Haz un vídeo como reparar una batería que no carga. Metodo desarmarla. Revisar placa por placa, y restaurar la que no sirve. Haciendo las fundiciones necesarias con nuevo poste fundido y hacerla funciona le otra vez.
@SorelOmba11 ай бұрын
Tu es le meilleur❤❤❤
@vadakdatta87943 жыл бұрын
This method is 100% work.
@aksks3713 жыл бұрын
I was using same method but it is very dangerous i got injured while performing this and the battery exploded
@jokekelleey2071 Жыл бұрын
I would think you could try to drill a hole in that terminal and then you know put some threads in it and then you could put a bolt right down the middle of the terminal I think that might work for a while. Then you can crimp some kind of connector on the wire and then both the wire down right in the middle of the terminal
@joeferreira6572 жыл бұрын
Good work, nice one.
@mehrdadyektaparast13683 жыл бұрын
I believe he made a frame/border. Melt the solder and add additional solder without using a soldering iron. Very interesting.
@francisn4423 жыл бұрын
Are there chances of the battery exploding ?
@harshshrivastav84842 жыл бұрын
Imagine melting other terminal instead of the required one
@kheavmady87803 жыл бұрын
congratulations, u just saved its terminal but reduced the battery life (short circuit). Dont take thing from youtube seriously. Do some research.
@heethomas42092 жыл бұрын
He may use another batterie to do the welding 🚶
@supermick839 ай бұрын
Bullshit. Using a carbon rod increases resistance and reduces current so it's not a short circuit. Once he gave the battery a full charge afterwards it would be fine
@hendrasyamsuddin78842 жыл бұрын
Nah... Ini cara ngecor aki yang benar & pasti kuat 👍👍👍
@Kivid_mis_veritsevad Жыл бұрын
Short posts are so annoying when jump starting a car. Now I can fix that.
@allaroundmechanics25304 жыл бұрын
What size of wire you use sir and battery ....im trying that techniques very much appreciated sir
@mehrdadyektaparast13683 жыл бұрын
I believe he used a triple a battery core. Framed the terminal, shorted the battery rather than using a soldering iron to melt the solder. It’s Dangerous however if you are stuck in the middle of nowhere then you would do anything to get back
@luizclaudiopappi98037 ай бұрын
Não tem perigo de explodir a bateria por fechar curto ? 🇧🇷
@MrTechnic7 ай бұрын
No
@danielammann7433 жыл бұрын
Should be mentioned, lead fumes are toxic ... even touching without gloves is not recommended.
@BiteTheCurbNow3 жыл бұрын
I agree, this is only useful in a zombie apocalypse but the guys handy huh?
@williangraterol8313 Жыл бұрын
Ese metodo daña las baterias mejor es derretir el plomo y verterlo en el molde gracias
@chlyon3 жыл бұрын
my large truck battery which is all but new melted a little bit as I didnt have clamp tight and now acid spills from the terminal is this method safe Ie explosive gases and all ??
@GG-eg6kn2 жыл бұрын
The AA battery what is the middle core made from?
@tiiiooooooo2 жыл бұрын
graphite carbon rod
@GG-eg6kn2 жыл бұрын
@@tiiiooooooo thank you
@ajtrevino36632 жыл бұрын
Can you just sand it down? Maybe with a soft wheel grinder?
@FLANZA643 жыл бұрын
Why dont you buy BATTERY SHIMS instead of going through this hassle
@punitsrivastava64563 жыл бұрын
NICE
@ManAnyMusic9 ай бұрын
What do you call that melting thing?
@raufeequemechatronics67534 жыл бұрын
you are doing wrong way.at first you have to open battery cap
@sarmindabikan81584 жыл бұрын
Thank this battery reconditioning plan t.co/uUSuy6Yk5g for the help reconditioning my batteries. I had Three dead batteries scheduled for disposing of. But I was able to recondition them using this technique in just One hour! It really works for all kinds of batteries!
@eugenenuique85982 жыл бұрын
What type of metal strip used in the melting process? Thanks for the reply..
@jinyong37719122 жыл бұрын
we have tools , not need handmade : www.amazon.com/Adapters-Terminal-Converter-Positive-Negative/dp/B0B21X6F42/
@Tiger-md3ym Жыл бұрын
I agree that using your battery as an arc welder is not a good idea but, using Plumbing solder and a smelter with the tin can form and a propane torch.. I think this might actually work out. I would caution anyone about using a torch on a battery terminal because if the battery gets too hot it can explode as well as it gives off gases that are highly flammable. So this is my disclaimer, attempt this at your own risk. You also have to look at the type of battery, the one in the video is not sealed, LSA or AGM
@Tiger-md3ym Жыл бұрын
I've also heard that the Navy used to throw batteries overboard that they considered were dead and the batteries exploded like a depth charge because the saltwater reactivated or something.. dead batteries in salt water blow up. Again, at your own risk
@FrankGrimes97 ай бұрын
A year later I will tell you you didn't get any likes because we are here to fix a battery not listen to some grown man be a scary little girl. Man up. I did this yesterday with no problems
@ZubayrShaikh9 ай бұрын
If it works.. it works 😅
@bad-boy9295 жыл бұрын
Mere bhai battery ka cap khol liya kro warna battery blast ho jayegi
@iphone3gsdivine4 жыл бұрын
Craigslist ad: like new car battery for sale lightly used
@chanakyasinha80465 жыл бұрын
Bahut badhiya
@marjono44502 жыл бұрын
Kira2 klo begitu kuat sampe berapa lama yaa bang
@lalitsokhal32782 жыл бұрын
Sir battery ki plet hard ho jane k bad usko kase thik kar skte h please btay sir🙏
@freddysilva6171 Жыл бұрын
Esto es peligroso puede estallar la batería
@manumamu1005 жыл бұрын
Battery blast hosakti ha?
@AltafKhan-cb3yj4 жыл бұрын
Thanx its work
@MrTechnic4 жыл бұрын
You're welcome!
@WhatAMusic02 Жыл бұрын
A video you can smell
@vihreelinja47433 жыл бұрын
Healthy fumes to keep yo skin fresh
@javapratomo3 жыл бұрын
whats the name of that paper?
@AsianTechnic2 жыл бұрын
Don't try this method the battery can be explode also the battery damage
@FrankGrimes97 ай бұрын
Stop being a vagina man tf up
@techs55645 жыл бұрын
don't do this
@tonymoua10585 жыл бұрын
What's your suggestion on how to fix this without buying a new battery? I'm looking for alternative routes.
@techs55645 жыл бұрын
@@tonymoua1058 try to file upto make It plain. then solder a thimble.
@daveengstrom92502 жыл бұрын
Hydrogen gas. Stupid thing to do.
@nealdutta40692 жыл бұрын
Buying a new one is better....or replacing the exsisting terminals that damaged those post us a better and safer approach.
@vadakdatta87943 жыл бұрын
This work only for professional.
@urwinflorin80653 жыл бұрын
excuse me? can this damage the battery?
@Norgesbeste12 жыл бұрын
No its fine. if it dont blow up by battery gasses coming out and ignite !
@mubasherburki2634 Жыл бұрын
No music
@Pinkielover2 жыл бұрын
just welting lead
@robertospagnuolo6744 жыл бұрын
So you like torture you car battery ?!? Well, "good job"......!!!
@prasadmhashakhetri57084 жыл бұрын
Good
@paulreeder52413 жыл бұрын
Besides, just like every other clickbait, the gif you show at the title of the video is not what the video shows. The gif also shows the sides of the post being solid and smooth. The battery in the video shows none of this. The post shows just as much damage as you started with on the sides? Not impressed at all. Sorry, but someone had to point that out.
@FrankGrimes97 ай бұрын
Someone who didn't fix their battery or even try this method to tell anyone it doesn't work. Just save me $350. This method isn't for scared little donuts
@mustafamohd2344 жыл бұрын
I also tried after watching this video battery exploded I also got minor injuries 😭
@samira88874 жыл бұрын
Not certain about the points made but ,if anyone else wants to discover how to recondition batteries try t.co/YpdloYO92F ? Ive heard some super things about it and my co-worker got excellent success with it.
@RMalsawmtluanga3 жыл бұрын
Instructions unclear help
@FrankGrimes97 ай бұрын
You aren't smart enough to know not to let the battery get too hot. If you don't have common sense you got what you deserved
@planetinfluencedk53602 жыл бұрын
Bro which sheet you take to cover the terminal,
@muhammadtaahir8379 Жыл бұрын
Alluminium can
@planetinfluencedk5360 Жыл бұрын
@@muhammadtaahir8379 thanks
@paulreeder52413 жыл бұрын
You only repaired the top of the post? Nothing connects to the top of the post. The sides of the post are still damaged? This is where the connection happens. I don't get it. Sorry, but in my opinion, you did not fix this post.
@FrankGrimes97 ай бұрын
You're wrong my friend.
@lakhansingh52932 жыл бұрын
Aap kam acha h par ye riski h kyu ki battery 🔋 k sell gar ho jatye h
@balav57psw4 ай бұрын
Most important precaution , please removed all cell's went plug. free gas circulation . not removed dangerous explosive...... very very important . take care......
@thechum96533 жыл бұрын
Theres alot safer ways of doing this. Both for the battery and yourself
@jokuRsmil33 жыл бұрын
Then post one
@rickr20293 жыл бұрын
Yes, I am anxious to see your method as well! Please post!
@thechum96533 жыл бұрын
@@rickr2029 no
@rickr20293 жыл бұрын
@@thechum9653 because you have not 1 (one)!
@thechum96533 жыл бұрын
@@rickr2029 yes i do
@footballCartoon914 жыл бұрын
Amazing
@jokekelleey2071 Жыл бұрын
Seriously I suggest you not short that battery out like that the whole battery could blow up it'd be better to use a torch and meltdown some lead try to put it on there you could just ruin the whole battery by shorting it out like that you can't short a load like that it's too dangerous
@kinanlaham744 Жыл бұрын
The battery is not shorted. The carbon rod has high enough resistance to barely use a few watts.
@FrankGrimes97 ай бұрын
@@kinanlaham744they are parrots with the same comment from all the people who haven't done it
@seller5593 жыл бұрын
Son of a gun.
@darrensmith9407 Жыл бұрын
Ahh...you get the wrong guy trying to do this on a hot day and things are gonna go real bad for him * my 2 cents, buy the cheapest new battery with the longest warranty you can afford
@kinanlaham744 Жыл бұрын
This process doesn't pull much current. Most of the heat is in the carbon rod. A few watts.
@nawazshah34023 жыл бұрын
Bahi battri LA rawmatrial mil ta he
@johnbailey9682 Жыл бұрын
I would just buy a new battery !
@muhammadtaahir8379 Жыл бұрын
Most off us can't replace the battery as the poles get damaged all the time when used in a truck most of us take the battery out everyday that's what causes the damage
@dosmastrify3 ай бұрын
Get a shim!
@ajbrown20133 жыл бұрын
I just watch this entire video and at no time did I ever see a battery terminal being fixed the only thing I saw was a battery post post being fixed
@BDK6795 жыл бұрын
Hey my active terminal is not giving that spark,what is that?
@MrTechnic5 жыл бұрын
Low battery
@BDK6795 жыл бұрын
@@MrTechnic thanks Really appreciated
@kuruvanarasimha78493 жыл бұрын
Terminal loki edi karaga pettindi ,,,arthu kaadu
@MrImamx4 жыл бұрын
Not recomended
@kconcepcionbatterysupply24753 жыл бұрын
dont try this.. it is very dangerous. and no pre-caution..
@FrankGrimes97 ай бұрын
Don't be a puss like this guy. If you have common sense this works