Awesome video, straight to the point with very detailed steps but not over the to! 👍
@cruisinwithgreg11 күн бұрын
Gotta keep it simple and to the point!
@pastorfred346011 ай бұрын
great video...I'd like add a couple suggestions for people doing this for the first time...always a good idea to remove the cap on your brake fluid reservoir and then sit cap on top so air can get out but no debris can fall in as you retract the caliper because this forces fluid back toward the reservoir. Also, always spray the new rotor with brake cleaner because they come from the factory with a coating of light oil. And, it's a good idea to put grease on those caliper pins, the non-threaded surface. And finally, pump the brakes in the driveway with the car running while in park until you feel resistance before you start driving.
@cruisinwithgreg11 ай бұрын
Thanks for the additional info!
@foxxxyred16625 ай бұрын
Do I need to remove the cap if I'm only replacing the brake pads and not the rotors?
@pastorfred34605 ай бұрын
@@foxxxyred1662 always a good idea because you will need to compress the piston on the caliper to make room for the new pads which forces brake fluid back into the reservoir.
@isiahsmith6737 ай бұрын
auto zone gave me front pads with a wire, i would assume break sensor? are they the right pads> 2013 vw passat tdi se
@cruisinwithgreg7 ай бұрын
Yes the ones I got from there also had the sensor wire. If yours doesn't have a brake wear sensors, it is on to cut that off. It would be the same as if they weren't there at all. But verify yours doesn't have brake sensors first!
@glenfishing8 ай бұрын
Thanks Greg.
@foxxxyred16625 ай бұрын
If I am just replacing the brake pads, do you need to take the cap off of the brake fluid reservoir? If so, will I need to bleed the brakes, only just for replacing pads?
@cruisinwithgreg5 ай бұрын
You will not need to do a brake bleed if just replaying. You only NEED to bleed the brakes if you introduce air into the system like replacing calipers.
@RestInPisKA5 ай бұрын
Now take your 20.... (21\22) mm soket and a bar and remove caliper bracket bolts???? Can you please write a comment what size is it?
@cruisinwithgreg5 ай бұрын
Hey the caliper bracket bolts are 21mm as stated in the video!
@Sheriff_California5 ай бұрын
Super video 🤙🏼🤙🏼
@cruisinwithgreg5 ай бұрын
Right on!
@pocketfulof-dinerobeats6 ай бұрын
Thanks greg. Make sure yall hit yall hit the like button. 😎👍🏾💯
@shjesus2 ай бұрын
whats the torque specs for the caliper and the wheel?
@cruisinwithgreg8 күн бұрын
Guidance is not easy to find, but here are recommendations: Caliper carrier 196Nm Caliper mounting 30Nm Wheel lugs 120Nm
@philjones48029 күн бұрын
The passenger side has a sensor but I see no where to plug it
@cruisinwithgreg9 күн бұрын
Yea the pads sometimes come with them, but if you don't have place to plug it in just cut it off!
@phoenixmckay648211 ай бұрын
Can this video be followed for the rear brakes aswell?
@cruisinwithgreg11 ай бұрын
Hey! It is a little different to do the rears, not exactly the same! If you can do the fronts you can definitely do the rears though!