I swear this is the only KZbin video that really show the location and how to remove it...great vid.my brother 💯
@2carpros2 жыл бұрын
I appreciate that! Thanks for watching!
@martynaskaunas71564 жыл бұрын
Finally I can fix my abs sensors
@Humanflesh19882 жыл бұрын
This help immensely my abs light is driving me crazy
@2carpros2 жыл бұрын
Awesome! Thanks for watching!
@pibitos0033 жыл бұрын
Thanks much kid nice nice video , greetings from Maryland
@2carpros3 жыл бұрын
Thanks for watching!
@AhmedAli-jj4cq2 жыл бұрын
I have abs light and brake light always on. My car is matrix 2004. I checked the oil but no problem with it. Will it fix the problem, and is the wheel speed sensor in same area.
@the-bu3lb7 ай бұрын
My Saturn vue 2008 doesn’t have the screw in the back. The whole rotor “e break has to be removed just to unscrew the bolt.
@RichardLlarenas4 жыл бұрын
Thank you for this video, I am having issue on the sensors of my Chevrolet Malibu 2014 2.5L, do you have any factory service manual for it?
@2carpros4 жыл бұрын
That is a complicated question, if you go to our website www.2carpros.com and ask a question for free, an expert will be along shortly to help! Thanks for watching!
@skyentist273 жыл бұрын
Hey love your vids. I have a abs cable that needs to be replaced. I’ve seen a lot of videos where they change the sensor but not the cable. How hard would that be?
@hermilandovalencia46562 жыл бұрын
P
@fantasticphil38632 жыл бұрын
If a part of the cable is cut or chipped, splicing/resoldering might work, although the conditions in the wheel well can be pretty rough so seal the splice up as well as possible. Heat shrink is a must.
@kingofdubb2133 Жыл бұрын
In the Volvo 940 you have to take off the the front wheel bearing, much trickier than the one in the video
@josephbohme79173 жыл бұрын
Based on the elec cable 2 or 3 Plus wire I would have spliced it at the wheel well Screw an extra 2 hours.
@2carpros3 жыл бұрын
I can't show cool tricks like that because it isn't the proper way and everyone on the internet would yell at me. Thanks for watching!
@musicauthority78283 жыл бұрын
@@2carpros That is true, there's a reason why they put the connector in a less damaging environment. and splicing it together closer to the wheel is asking for trouble. bad wiring connections are one of the most common problems, there is on modern computerized vehicles. technicians are always tought to check the connections, as the first step in any procedure. but taking so much the vehicle apart isn't the answer, just put the connector in a decent location. I agree with you I will probably catch hell for this reply, because people don't realize how bad of an environment the undercarriage of a vehicle is especially in the winter. if the reason is to keep DIYers from doing the repair? these videos are proof that they are going to learn how to do it anyway.
@osvaldoneedfordiecasttrujillo3 жыл бұрын
My problem became a DIY after watching this video
@karanmakhija2 жыл бұрын
2018 Mercedes Sprinter a code for the right rear speed sensor... I might tackle to do this...
@bwilliams22162 жыл бұрын
Thanks bro 😎
@2carpros2 жыл бұрын
Thanks for watching!
@John.Skelton2 жыл бұрын
The title said "EASY" and your pulling out the back seat and stuff. Lol! Still a great video tho! Well done!
@2carpros2 жыл бұрын
It is easy just time consuming. I feel like those are very different. Thanks for watching John!
@chanogeezy602210 ай бұрын
😂😂😂😂😂
@edwardrogers-wright160410 ай бұрын
Excellent video! Could it have been easier splicing the harness near somewhere near the wheel?
@2carpros10 ай бұрын
Yep! But then I get all the internet "experts" telling me how dumb I am because I could have changed the impedance of the line. Thanks for watching!
@osvaldoneedfordiecasttrujillo3 жыл бұрын
This helps so much
@2carpros3 жыл бұрын
Thanks for watching!
@juancasanova24492 жыл бұрын
Thanks very informative and detailed 👍
@2carpros2 жыл бұрын
Glad it was helpful!
@marksmith39912 жыл бұрын
@@2carpros
@brohdaw6 ай бұрын
I seen the wires but tonight I came upon sensors that look like just the sensors only and no wires. Also no indication of rear left or rear right so now I’m a little nervous of what’s the right part and I can’t take the vehicle apart first and wait to have the part shipped after removing and seeing the part
@brohdaw6 ай бұрын
For some reason I can’t share photo 😡 but this is the one without the wire NTK ABS Wheel Speed Sensor Part # AB2048
@hybridramper-futurearmy11603 жыл бұрын
Finally i can fix my abs 6 pack abs lol
@2carpros3 жыл бұрын
Yes! Thanks for watching!
@daveyb981266 ай бұрын
For front wheel drive, I'm assuming the sensors are on front wheels?
@2carpros6 ай бұрын
They are on all wheels that have ABS. So most cars have 4. Thanks for watching!
@darrickcruse20863 жыл бұрын
I had a code of c003a for a rear right wheel sensor on a 2013 Ford Escape I’m gonna check the tone ring first to see if it’s cracked or broken but once I change the sensor or tone ring depending on which it is will my abs and traction light go away? Thank you in advance if I get a reply and if not still thank you
@gregbenwell61734 жыл бұрын
I have a 1999 F-150 and I was told you almost have to disassemble the whole hub just to get the front wheel speed sensor out! I know that it is already a pain to remove on my truck, just because you DO have to remove the front brake rotor to even get to the Allen head cap screw holding mine in place with means taking apart the front brakes just to get to it!!
@2carpros4 жыл бұрын
That's the price you pay for the sweet pleasure of truck ownership. Thanks for watching! I have a video on doing a brake job on your exact truck if you are interested.
@kaylagillberg56762 жыл бұрын
What about a 2018 Kia soul base model? Rear sensor is bad. How much work to replace it and location????
@justinrebarchek36203 жыл бұрын
Damn that auto designer should have to fix a hundred of these🤣
@2carpros3 жыл бұрын
That would make things easier! Thanks for watching!
@jrloopy19844 ай бұрын
What size is the wheel speed sensor bolt?
@parkstraat9 Жыл бұрын
if you have small hands and bend the cover (inside and outside) a bit can can replace the cable without removeing al the covers. tape a rope to the connector and pull the cable from the inside to the outside. then use the rope to pull the new cable from the outside inwards. unfortunately swapping the sensors did not fix the bumpy braking for me (the two on the front were dead, two in the rear where ok) if I have bumpy braking (especially slow riding towards a traffic light) what else can it be? the abs module itself? If I disconnect the abs module it brakes much beter, not perfect, but much better. I ride a kia sportage 2006
@chrisgarwood91402 жыл бұрын
Assuming you have continuity, what would be the cons of just splicing in a new plug at the wheel well?
@2carpros2 жыл бұрын
There could be a resistance change with the splicing but I think it would work just fine. I'm sure there will be an electrical engineer along shortly to tell me off and why it's the worst idea in the world. Thanks for watching!
@mennowzer41643 жыл бұрын
Good video...thanks
@2carpros3 жыл бұрын
Thanks for watching!
@fayjason Жыл бұрын
Ive got a 00 Buick LeSabere. I don’t have any ABS or check engine lights on but when I hook up my code reader, I get code C1298( Class 2 serial Data link malfunction) and C1245 (Acceleration output). I’ve been told to check my wheel speed sensor. Is this a good place to start?
@willzwilly40763 жыл бұрын
Thank you for the video. How do you know which sensor is bad? I have 2003 Avalon.
@2carpros3 жыл бұрын
Your canner will tell you. Thanks for watching!
@willzwilly40763 жыл бұрын
@@2carpros thank you Actually the code was P0500 , the mechanic told me it's for one of the ABS sensors and he doesn't know which one. So I googled the code and found out it's the speed sensor. Saved alot of money
@voorvideos3 жыл бұрын
here in norway they want 18000 nkr to switch both sensors back, becouse both bolts that hold sensor are brocken inside so they must drill it out, its a double wheeler back, if i can get the wheels off myself u think its the same as in your video or diffrent becouse off double wheels? ty
@joshuaarango99733 жыл бұрын
Thank you I appreciate this post
@2carpros3 жыл бұрын
Thank you for watching Joshua!
@mikecohen76462 жыл бұрын
I enjoyed the replacement of the ABS sensor but you never mentioned the make and model of the vehicle
@mikecohen7646 Жыл бұрын
It was a 2016 Hyundai sonata
@Eddie89 Жыл бұрын
Video description says Kia Sportage
@chien-shengtsai86262 жыл бұрын
Good video, thanks. But I do not have a lift, so it'll be harder.
@melodyjones60632 жыл бұрын
We changed the abs speed sensors on both sides front on a 2004 buick raineer and the brake system service bell keeps going and says brake service system on screen what can we do to get it to stop
@LRBennettInc3 жыл бұрын
2003 prius with a c1241 EC it's saying a ABS issue? Sensor? Thanks
@kevfla4 жыл бұрын
My Hyundai Tucson is showing code for the right rear ABS wheel speed sensor but the dealer says I have to replace the whole hub assembly. Does this sound correct for a 2016?
@2carpros3 жыл бұрын
No it doesn't. If the sensor has gone bad why can't you just replace the sensor? Because they want more money. Thanks for watching!
@luislozano79473 жыл бұрын
Agree. They just want more $ from you. Now, if warranty is still active and this is covered by warranty, then by all means have them do more work and get you all that new stuff in there. If you don’t have warranty, I suggest buying the ABS wheel speed sensor on rockauto.com The loco Kia dealer (yea, in Spanish this means “crazy” but sounds like I’m saying “local” lol) wants $147 + tax for the ABS wheel speed sensor for my 2013 optima. Bought it online: $39 for sensor $4.50 tax $25 next day shipping $68.50 total...and installed myself. Easy just like the video shows! BTW, rockauto sells the brand “Mando” which is a tier 1 manufacturer for Hyundai/Kia OEM parts. Hope this helps you and everyone else getting suckered into dealer pricing. 👍🏼
@ccastro306 Жыл бұрын
is there an easy way to tell which one is bad? I have a 1996 Thunderbird
@2carpros Жыл бұрын
The scanner usually will tell you which one is bad. Thanks for watching!
@edwardrogers-wright160410 ай бұрын
Can an old 2010 scanner tell which one is bad?
@M0xh3 жыл бұрын
So if I have a code that say front wheel right side sensor I change and the check light will go
@aldofoflores107911 ай бұрын
How to remove a wheel speed sensor rear of a sonata Hyundai hybrid
@charlenedodson54112 жыл бұрын
How would you know if that's what you need to replace? Like if it's one side.
@2carpros2 жыл бұрын
When you plug in a scanner it will tell you which sensor isn't working properly. Thanks for watching!
@BESFLIX2 жыл бұрын
Nice
@joseherrera22072 жыл бұрын
Question I replaced the front wheel bearing on 2011 Nissan Sentra an now I have the abs light on an dvc light on how I make them turn off
@2carpros2 жыл бұрын
Clear the codes using an ABS scanning tool and see if they come back. Thanks for watching!
@miloo3182 жыл бұрын
What vehicle is in your video?
@2carpros2 жыл бұрын
A 2005 Kia Sportage. Thanks for watching!
@leo420033 жыл бұрын
Should you put grease on the sensor?...
@2carpros3 жыл бұрын
No. It needs to be clean. Thanks for watching!
@TiktokBrandoniMacaroni3 жыл бұрын
Can u tell me the dealer says that I need a abs speed sensor and that they are going to replace the whole hub does this seem right and why is 400 for the part for 2019 Nissan Titan that only has 11000 miles on it ?? Can I just buy a tool and keep clearing the code ??
@2carpros3 жыл бұрын
You should just be able to replace the sensor unless it is a really silly design. That is very low miles, you really shouldn't have any problems at this time. I would warranty it. If you just keep clearing the code the ABS might not work. Thanks for watching!
@musicauthority78283 жыл бұрын
If I were you I would get a second opinion, a Nissan Titan is a pickup truck and more than likely all wheel drive which could be a factor. but normally ABS sensors are remove able by themselves, and don't require a whole other component to be removed to change them. I would definitely seek a second opinion no doubt.
@douglascoffman2741 Жыл бұрын
2008 toyota hylander
@joshuaarceneaux38412 жыл бұрын
Where can I find a Left Rear Wheel Speed Sensor For A 95 Cadillac Deville 4.9L Code I’m Seeing is T037
@2carpros2 жыл бұрын
Try RockAuto Thanks for watching!
@DHard-mc2uw3 жыл бұрын
What make and model was the vehicle you were working on???
@2carpros3 жыл бұрын
This was a 2005 Kia Sportage. But all cars work basically the same. Thanks for watching!
@musicauthority78283 жыл бұрын
@@2carpros I wondered that myself but didn't ask. no wonder why you had to remove so much of the interior panels. a Sportage is an SUV, on a regular passenger car it's possible that procedure, might be done from in the trunk compartment of the vehicle. requiring considerably less interior panels to be removed. something that I noticed that a lot of people in the comment section complained about including myself. which might be less of an issue on average passenger cars. that is a very good question that this particular veiwer brought up (thanks veiwer). and probably a question that I should have thought of much earlier in this comment section, instead of whining and complaining so much.
@philharden1644 жыл бұрын
Why does the new cable look used..like the one you took out??
@2carpros4 жыл бұрын
New used part. Thanks for watching!
@jiwcoronado2 жыл бұрын
i changed all my 4 abs sensor but in still having abs signals on my cluster on 1998 528 bmw whats my next step im getting confused please help
@2carpros2 жыл бұрын
You need to scan the ABS module and see what the actual problem is. Thanks for watching!
@MermaidBigDrip3 жыл бұрын
Hi. Where can I buy a good new sensor?
@2carpros3 жыл бұрын
Try Rockauto.com or summitracing.com Thanks for watching!
@MikeJones_BACKTHEN2 жыл бұрын
Amazon
@Slithey74332 жыл бұрын
Should’ve demonstrated a 2005 GMC Sierra front wheel, on which it’s necessary to remove the brake rotor in order to get to the sensor.
@kingofdubb2133 Жыл бұрын
Volvo 940 you have to take off the wheel bearing as well!
@CarlOblander9 ай бұрын
Maybe h didn't happen to have have a spare GMC Sierra sitting around, idiot!!!!
@jaylawrence65562 жыл бұрын
Can the sensor cause the car to lag shifting
@chaselyons20332 жыл бұрын
No
@danielschaeffer398625 күн бұрын
On my Tundra, the ABS, traction control and 4HI lit up. Every time the 4HI is lit, it retards.
@MrAgummer3 жыл бұрын
Is there a trick to know which one is bad? So you only have to do one without disassembly and reassembly until you find the bad guy?
@ChapoGuzman8963 жыл бұрын
Yeah buy a abs sensor
@2carpros3 жыл бұрын
Yeah you need an ABS scanner and it will tell you which one it is. Thanks for watching Adam!
@Benny46drift3 жыл бұрын
Jaguar was the easiest ever, I am back as I now have to do a 2014 MK4 Clio which looks like it disappears up like this
@Benny46drift3 жыл бұрын
side note... Get the Bosch GDR, amazing little bit of kit and you already have the batteries for it
@anon8638 Жыл бұрын
What Jaguar did you have? I have a 07 S type I need to change an abs sensor on
@kiwi73413 жыл бұрын
Only just slightly snug up the bolt, otherwise the next guy will snap it off removing it...😳
@timsterkhim6532 жыл бұрын
Kiwi your absolutely right mine sensor was broken when I tried to pried it out it was bond to the wheel hub. I'm thinking about cut and connecting instead of spending hours removing half the rear interior
@graphicscardtech31673 жыл бұрын
How did test to see is bad?
@2carpros3 жыл бұрын
The ABS code will tell you that. Thanks for watching!
@MikeJones_BACKTHEN2 жыл бұрын
Why. You disconnect the battery
@2carpros2 жыл бұрын
So the computer doesn't freak out. Thanks for watching!
@superfuntime31074 жыл бұрын
Waiting for the big block chevrolet start up.
@2carpros4 жыл бұрын
Oh its coming! Thanks for watching!
@superfuntime31074 жыл бұрын
@@2carpros word
@josephbohme79173 жыл бұрын
at 22 maybe, how many cars have you wrestled to have done em all to be the hardest
@2carpros3 жыл бұрын
This one is up there, but the toughest cars to work on typically are the expensive ones. Thanks for watching!
@alexanderlenoir75673 жыл бұрын
Traction control light and abs light on on a 2013 dodge journey, is the vehicle drivable.
@CarObsession3 жыл бұрын
Technically, yes, but you're likely to have no ABS, so I wouldn't risk it. HTH.
@2carpros3 жыл бұрын
Yes it is drivable, but your ABS might not work. It is dangerous. Thanks for watching!
@musicauthority78283 жыл бұрын
When the ABS light comes on it's normally due do to a bad wheel sensor. in which case the computer basically turns off the ABS, allowing the brake system to be the same as a vehicle with not equipped ABS. which means the brakes can have a full lock up condition. but a check ABS light can also mean there are other issues with the ABS, that could lead to complete brake failure. the only way a person will know if it's a sensor is if the vehicle is connected to a scanner. so like with any check system lights, it's really wise to have the vehicle checked out and repaired.
@acehomecosc2 жыл бұрын
I have my brake light, ABS light and Traction Control light going off for a rear speed sensor on my 2014 Toyota 4Runner. I have been driving mine for about a month with these on but definitely would not recommend it.
@abrios-mb7ej2 жыл бұрын
@@acehomecosc my traction light is on and I don't know what to do it turn of but them after a while it will turn on again
@axtra924 жыл бұрын
So where is the second bro?
@2carpros4 жыл бұрын
On our website 2CarPros.com Thanks for watching!
@crazypete37593 жыл бұрын
so easy, unless you own an infiniti qx30 that makes you remove the wheel well cover to get access to the connector. turns a 10 minute job into an hour job....
@nomasksnovaxxes76202 жыл бұрын
Easy enough if you're speed sensor isn't basically stuck in there.
@tyrelltalbert4853 жыл бұрын
And you talking about EASY! lol
@2carpros3 жыл бұрын
Yeah it's just one bolt............ technically. Thanks for watching!
@jacobcallahan48133 жыл бұрын
Mine never came out that easy
@2carpros3 жыл бұрын
Sometimes they can get stuck with road grime. Thanks for watching!
@blank-dr2kx3 жыл бұрын
Local garage wants £200 to replace 1 offside sensor... Kia sportage 2015
@2carpros3 жыл бұрын
Dang that's expensive! Must be under a ton of body panels. Thanks for watching!
@ethanlinton11593 жыл бұрын
buy one in amazon or ebay. they areso cheap as those do not need a heat for fail as other sensors
@jasongaudreau20752 жыл бұрын
It’s all easy til you got a broken bolt in the rear axle of a Nissan truck!
@musicauthority78283 жыл бұрын
This is a perfect example of engineers that can't hit their ass with both hands. designing components for automobiles, that makes a simple procedure, such as R&Ring a simple component as a ABS sensor, turn into such a headache. that is beyond ridiculous to have to take so much of the car apart just to R&R an ABS sensor. perhaps maybe they should have to do the work, on their own handy work. (designs) then maybe we would see less of this stupidity. it doesn't make sense, I can see putting the connector in a better environment. but having to take so much of the vehicle apart to do the repair, is just plain stupid.
@2carpros3 жыл бұрын
That's modern automotive repair to be honest. These engineers are paid to make it cheap as possible to assemble not to work on sadly. Thanks for watching!
@EstelleSarah802 жыл бұрын
Easy? Not so much. What kind of car is that?
@2carpros2 жыл бұрын
It is usually easier. This is about as tough as it gets. This was a Kia Sportage from 2005 I believe. Thanks for watching!
@Tonypre19893 жыл бұрын
easy? i wonder whats not to easy
@garftup20423 жыл бұрын
Wow I'm not impressed at all this gentleman said that this was a very difficult rear speed sensor to change I guess he's never dealt with the other half lives in Durham fKing rear drum! Thanks a lot for show me how to do something my grandchild could've showed me!
@2carpros3 жыл бұрын
Very difficult for a speed sensor due to needing to take about the entire rear interior. Usually is a plug a short distance away. It's called context. There will always be things that humans do that are way harder. So we compare things to similar things to gauge difficulty. Sorry if that was lost on you. Thanks for watching!
@tonydeniro2842 жыл бұрын
That does not look easy....u took apart half the car for one sensor...
@2carpros2 жыл бұрын
As I said in the video, this is about as hard as it gets. I'd rather show a hard one and you get an easy one than the other way around. Thanks for watching!
@ethanlinton11593 жыл бұрын
The stupid mechanic mobile forgot to put the screws of the sensor when he was doing a work on the right side. I drove and it broke.
@2carpros3 жыл бұрын
Mobile mechanic are usually not up to the same quality as a shop. Sorry that happened to you. Thanks for watching Ethan!
@claudiobedoya15423 жыл бұрын
Hope he fixed it for free
3 ай бұрын
what vehcile
@slow1le_2393 жыл бұрын
I have a stabilitrack light on is having a bad abs making this light come on? Or it doesn’t have nothing to be w that
@clumonster61523 жыл бұрын
Same
@slow1le_2393 жыл бұрын
@@clumonster6152 I changed my abs sensors and it wasn’t that till this day I still have that stabilitrack light every time I turn on the car