Nice and easy. Thanks for not making a 30 minute video full of unnecessary chatter.
@cesartapia6102 ай бұрын
Thank you so much for making this video. It helped me get the job done the right way with all necessary details included. Most of the other videos on here skip over the hard parts, but you are kind enough to walk us right through the whole job. Many thanks!
@bramham9996 жыл бұрын
wish all how to videos are like this... clear and concise. thanks
@HowtoAutomotive6 жыл бұрын
Bramham Hardwood and Laminates thank you! Did you get your ride all straightened out?
@lamberttabi47786 жыл бұрын
Hello is this the same procedure to change the camshaft sensor on bmw 328i?
@HowtoAutomotive6 жыл бұрын
Lambert Tabi no that season is inside the valve cover
@lamberttabi47786 жыл бұрын
So how can i replace the camshaft sensor on a bmw 328i? Please i need ur expertise advise
@baims83676 жыл бұрын
2005 bmw x3. Changed the oil seperator and tubes to fix vacuume leak now cranks 5 6 xs untill starts code says cam sensor does unplugging it f these up? I may of over looked it and left unplugged was fine before
@tsmgguy Жыл бұрын
Surprisingly easy DIY job, thanks! Of course, symptoms of a bad cam sensor are difficulty in starting, with poor running and idle. I at first suspected the fuel pump and replaced it. No help. Then I checked the codes and there it was, P0344 which is "camshaft position sensor A intermittent". A new OE cam position sensor was about $60. I did the job in my driveway in about an hour with no problems. The car runs perfectly now.
@scottklein46944 жыл бұрын
Great video! Tying a string to the end of the sensor wire where it plugs in under the air box will make threading the new wire into place easier.
@adpgoodwin3 жыл бұрын
Super clear and concise, thank you! First major(ish) bit of work I've done on my E46 and everything went really smoothly. Note for others: I had to remove my oil filter cap to get better access to the camshaft bolt, which you might have to do unless you have a torque wrench with a flexible head like he does.
@HowtoAutomotive3 жыл бұрын
Glad the video was helpful and everything went smooth. Thank you for watching!
@robertvisser58793 жыл бұрын
Thanks a lot Brian, brilliant instruction!
@bradjohnson49855 жыл бұрын
Bravo, very good instructions.
@HowtoAutomotive5 жыл бұрын
Thank you!
@Dougarony4 жыл бұрын
would a bad crank sensor "A" cause stalling & no restart? Thanks much!
@Jay-wl9tp4 жыл бұрын
Doug Tyree did you figure it out?
@Dougarony4 жыл бұрын
@@Jay-wl9tp Thanks much for the follow up. Well I got her running strong, however now it seems like a Throttle position sensor issue perhaps? Runs Great @ WOT, but seems to have a lot of Pedal travel to get her going?
@Jay-wl9tp4 жыл бұрын
Doug Tyree I just put mines in the shop Friday. I’ll let you know what the results are. I’m having the no crank no start
@Dougarony4 жыл бұрын
@@Jay-wl9tp OK good luck, have u had the codes checked?
@Jay-wl9tp4 жыл бұрын
Doug Tyree It was the starter !
@PAPERBOYS-ek6ke3 жыл бұрын
Good informative video.
@puertoroc1234564 жыл бұрын
@ How to Automotive i have a E46 M3 and my set up looks different. How would I do this on my M3? I'm getting p0010 and p0012 codes
@Liveforeever2 жыл бұрын
Thank you
@HowtoAutomotive2 жыл бұрын
Thank you for watching!
@LilHonda97 Жыл бұрын
My vanos is stripped and it's on extremely tight how do I get it off man... I can't even replace my intake cam shaft sensor that's under it.. helpp mmmeee I also don't have this size. I've tried.
@damianspears246910 ай бұрын
What about on a m56 325i
@dgod67153 жыл бұрын
Is this for a 530i as well?
@LilHonda97 Жыл бұрын
I'm having p1343, p1345, p1351, misfire with low fuel, I replaced the fuel pump, fuel injectors, ignition coils and sparks and even the MAF SENSOR, and replaced yesterday's the exhaust cam sensor. Still nun, it's 5spd manual 2001 e46 m54... so it just keeps stalling I dont even drive it. It's bad. It's on my youtube I need help with this.. anyone help.
@MrJJ25235 жыл бұрын
I've changed it before but it doesn't work because the sensor is not exact same. And no one mentioned that the sensor's head is bigger than the old one. Did you guys find the same problem like me? Thanks
@blitzcourt50214 жыл бұрын
Jack Jitphulphon make sure you ordered bank 1 or A and not B or 2 because that one has a bigger head
@MrJJ25234 жыл бұрын
Blitz Court thanks for your kind message👍
@aikeemgraves96103 жыл бұрын
Was your code p1525
@redflagNeagle4 жыл бұрын
What's the part number for that plz
@HowtoAutomotive4 жыл бұрын
Elite Edi I believe there’s a link for in the description the video.