How To Replace any Smartphone USB Charging Port Without Heat Gun properly

[@revolruf]

Dude! Clean your soldering iron tip!!!! Get a sponge slightly damp and swipe the tip on it, it's not hard. A clean tip and a bit of fresh solder on it when you are done keeps it like new for a long time.

[@CatPBWater]

At 3:35ish, it looks like the electronics above the port get damaged. This method got the job done but not without consequence.

[@4custaywithme]

I think looking carefully they did not, but that's the best method of blowing destroys phones than this method. the components are very intact. There are no components only the blackish ink which seems the same at the start compared to yours at 1:00 the difference is the same. Blow gun shortens the life of a mb especially when in careless hands.

[@stopthephilosophicalzombie9017]

I think that's just flux sucking up some soot into another area.

[@AntiDoctor-cx2jd]

an actual text description of what's happening would go a long way

[@abidaliyousafzai3123]

Extraordinary,, very helpful

[@YNFERNUS666]

He visto malas ejecuciones de trabajos,hasta yo he hecho desastres...pero éste chaval me supera,un desastre por donde lo mires.

[@christophertadeo6120]

Rule of thumb, The less lead or paste u use to get the job done, the better the result would be... 😳👍

[@RingZero]

Bhai saab! great job. Keep that solder iron clean for a quality work, after all you're demonstrating your work on KZbin.

[@MmanzilsTech]

I will try my best

[@joemarfrias1996]

Your idea is very useful for beginners thank you for sharing your tactical....

[@MmanzilsTech]

Thank You Bro

[@jimcruise9632]

I need this idea👌👌👌

[@thekontuli2828]

"It does not matter whether the cat is black or white; as long as it can catch mice" ~ N. Mandela

[@munindradas621]

Sir,jo cycle ki rechargeable headlight ate hen uski charging port ukhar jaye uha par naya charging port laga sakte hen ?

[@obinnakingsley8875]

❤❤❤❤❤❤,EXCELLENT WORK BOSS

[@မောင်မောင်မမ]

It's working for my phone.Thank U so much.I have no idea for that because I have no hot gun. AWESOME Sir

[@СергейПерттунен]

Для тех, кто "в танке". Это способ заменить разъём на случай, если вышел из строя фен или его нет под рукой, а замена ну просто таки горит. От себя: Гораздо проще будет снять, если иметь в хозяйстве сплав розе. Если разбавить припой на всех дорожках и ножках сплавом розе - то не нужно будет даже заливать припоем весь разъём - достаточно будет немного погреть, измазав флюсом

[@DmitryMaster]

Для тех, кто "вылез из танка": если сломался фен, нет сплава Розе, кончился флюс, отключили свет... Может ну его нафиг, заниматься ремонтом? Я 30 лет паяю, а фен живой, да и что это за горящий случай?

[@yotagoogleplay894]

​@@DmitryMaster ну какой тогда ремотник если нет сплава розе. Если есть паяльник и обязан быть и сплав розе!

[@DmitryMaster]

@@yotagoogleplay894 так-то логично, но ремонтником сейчас называет себя каждый второй, заменивший сгоревший в лампочке светодиод фольгой.

[@global_fusion_infomatics]

I'm already using same method without any loss good result... Better than smd work.. Use high watt soldering iron

[@MmanzilsTech]

Great 👍

[@bigpaul009]

Which is the best solder wick to use, I bought some but it doesn't get out of the holes to put the new one in, TIA.

[@TYPICALGHOSTSNIPER]

Solder wick is all same it's just copper wire.

[@Gujjar-k1y]

​@@TYPICALGHOSTSNIPER No some high quality and some low thick and thin 😊

[@Gujjar-k1y]

​@@TYPICALGHOSTSNIPER No some high quality and some low thick and thin 😊

[@Gujjar-k1y]

Mechanic wick best 😊

[@rodrigogregorio2877]

This idea is useful without hot air, I used the same technique before, but if you have hot air much better..

[@jaredbengco4708]

What's that copper or bronze strip that you used for removing lead? Thanks man.

[@Tompzu592]

desoldering wick

[@mallowricyano937]

or strip a coaxial cable

[@larrymyers5989]

Desoldering wick. I remember from high school!

[@stopthephilosophicalzombie9017]

Any idea how I could do this with a 90˚ vertical mount through-pin USB type B? As it is the solder is clogging the holes and I have no idea how to heat them all up without a heat gun. I guess I'm going to have to invest in one.

[@evansoloruntobi4373]

What's that thing you are using to clear and opens the holes

[@pratikpandey7296]

desolder wire

[@j.caspersoundcatalyst2428]

Soldering wick

[@j.caspersoundcatalyst2428]

And desoldering wire

[@balduinlefterov5927]

Use low melt solderpaste 138 C, or low melting point solder wire. It's easy, fast, cheap and professional.

[@r.k6270]

sir, may i know the flux name for desoldering the " IC " in the boat sound bar 2050

[@lungisamayekiso736]

Nice work especially when you put it back manual

[@TechnicalZafarShaikhOfficial]

Good 👍 work but microphone 99% dead hoga

[@kadirkaraca8711]

bad work , microphone is dead bro

[@danielcano7492]

Do why?

[@danielcano7492]

The flux is not in contact with the microphone

[@workingonthatphone]

Who tell you that the microphone is dead did you try it ?

[@OnePunchHeizou]

depends on what solder he used, if low temp solder then i guess it should be fine otherwise mic isn't the only component getting damaged.

[@Jeetutech6]

Microphone dead by overheat

[@jerryboy5876]

What is that copper strip called that you used after you took the USB port out?

[@abdulrafy2087]

Soldering vick

[@iloveACID]

Wick

[@j.caspersoundcatalyst2428]

Or strip a coax cable it's the same

[@gotindrachenhart]

Ok, its called a soldering iron. Also, olease look up a video about how to properly maintain the tip. Soldering irons must be "tinned" in order to work well. It makes soldering much easier! Id suggest looking up some videos in this because it really does make a big difference. Then, use a small damp sponge or wet hand towel or rag to rub the tip against to clean it between soldering steps, this keeps the gunk from building up and also removes the oxidization layer. Thus all will also extend the life if the tip by years. Be careful of adjacent components. You niked the surface mounts abouve this charge port. Easy to brick the pcb this way.

[@Fishbone4u]

Agreed! Soldering iron tip looks terrible. Sloppy and lazy IMO.

[@gotindrachenhart]

@@Fishbone4u basic stuff, right?

[@fugeeohu9357]

I've been trying to replace chargin ports on LG Aristo 2 I have a heat gun and soldering iron but I don't have any low melt solder I have a flux pen if that helps I haven't tried using the flux One board I got it so messed up I can no longer see the pins I'm lost on that one Another board I did it with the heat gun at a glance it looks at least not a mess but the pins don't really seem to be connected The way I messed up the other one was trying to connect the pins A glob of solder got on there and then I had a struggle trying to remove it then I took the port back off and find that I can no longer find the pins What a mess Replacing charging ports isn't easy I think maybe I should stop trying until I get some low melt solder? I still haven't gotten the technique for this down

[@muazzambhatti1672]

you will destroy 4 or 5 charging ports but you will get the hang of the technique automatically. keep watching video tutorials and try to apply them as well

[@clod_23]

What liquid are you using to clean with the cotton swab?

[@danielgonzalez2582]

isopropyl alcohol (propan-2-ol), it's a good cleaner and evaporates fast and doesn't contain any water, unlike ethanol (ethilic alcohol)

[@j.caspersoundcatalyst2428]

I believe it's flux paste. It cleans everything off very well and helps with the adhering process of the fresh solder.

[@j.caspersoundcatalyst2428]

Ah, I stand corrected and now enlightened, thank you Mr. Gonzales2582, much appreciated.

[@benjaminkoomson7005]

What is that long brown thing you used to clear the led left off the board ?

[@maximumeffort5865]

Solder wig its some coper wire

[@starryeyed132]

Solder wick

[@vgtech4716]

Nice tech💓💝💕❤️

[@d.raxvrai]

hello guys, i have a hp spectre laptop but the problem with it its not charging the usb c port is very lose, so i called the call centre they said they should change the whole motherboard because it is directly connected, so i was searching for a usb module so that i can solder it but i have a doubt that can we use any usb module or there should specific ones? if there is any specific ones please let me know

[@canoris267]

Hello I have a question. Will the charging connector from Samsung S10 ,S10e,S20 on S20 Fe? Or do such models have identical connectors?

[@j.caspersoundcatalyst2428]

Pretty sure they are all the same as with phones. If they are a USB micro then any USB micro will be the same process. As with usbc, etc.

[@CreatorStudio-c4m]

Pls what is the name of that thing you are using to clean the led after removing

[@j.caspersoundcatalyst2428]

That's a soldering wick. If you don't have one you can strip apart an old coax cable (for like old cable tv) and you will find the same exact cable wire within. Make wicks from it.

[@ANUAFOHUN]

Please what is the name of that brush you are using

[@7207691302]

Next level sir👌

[@MmanzilsTech]

Thank you sir

[@-iIIiiiiiIiiiiIIIiiIi-]

I feel like I'm being gaslit.

[@bhoot1702]

No. But you have to be careful with this method and try not to damage neighbouring components. Just use kapton tape to cover components like mic and other ics and components And to be as quick as possible, making sure not to overheat Main thing is using low melting solder while removing the connector

[@delicrux]

... Why are you using solder to remove the port when you can just use flux ... And and remove it without burning the board?? I've seen Louise remove components using flux and from my own experience I'm having trouble understanding this method

[@dangalf84]

How do you open the phone case to access the internals without a heat gun though?

[@rangorangila1306]

a good throw into a concrete wall

[@PRIMA.COSMOS]

Присоска и медиатор

[@j.caspersoundcatalyst2428]

High heat from a hair dryer. Just takes a little longer. Done this many times.

[@ВячеславЛевченко-ь7н]

Если нет фена, так проще отпаять разъём?

[@johnorji556]

what's the name of the brown stuff in cleaning the panel board

[@etechbyfasal629]

👍 good trick 👌

[@preston963]

You are right because there either laptops or mobile phones but a little dose of low melt falls out all good been a tech 40yrs

[@mangeshpadviVideo9292]

🎉🎉🎉🎉🎉🎉very nice

[@youtubshortfun]

By that much soldering wire you used... You can buy hot gun

[@Huzayfah_Osman]

Thanks bro✅💚

[@DaniJackk]

is it led u put on it?

[@sachinazad7271]

bro. trick toh theek hai, but mic 10000% not working

[@meranplus]

To desolder just use low melt solder

[@durgarajumalladi50]

Nice 👍👍👍

[@izonehyderabad320]

Soldering rod witch company did you used

[@MmanzilsTech]

Quick

[@j.caspersoundcatalyst2428]

Rosin core

[@abidaliyousafzai3123]

Very very excellent work sir

[@firdousahmad5648]

How much watt soldering iron you use it?

[@MmanzilsTech]

80watt

[@revolruf]

80 watt is good but not the cheap ones on ebay. I've purchased 3 of them. 2 never got hot enough 1 never got hot at all. I know it's not going to be something most people would want to spend too much money on but if you use it more frequently just get a Weller. They always work.

[@firdousahmad5648]

I purchased lot of 80 watt soldering irons but all not working well after i use 12 v soldering pen and computer SMPS power supply and give 16v to 12v soldering pen now it works fine

[@WEVLTHX]

Title : Replace charging port without heat gun. Video : Process to use heat gun. Mind-blowing...

[@crystalmaltby3202]

😂

[@bdafonefixguy]

i missed that. i didnt see heat gun used (???)

[@den0matic]

???

[@spiritlight4440]

Any recommendations for a microscope?

[@tellnseeartificialjewelry2971]

Bhai Link be dia kro na Ya Ports ya sockets kahan say Buy krne hain

[@eng.tkmelectr6598]

Wait I thought the leads should be pressed on the nickel blade and not one on the nickel blade and the other one on the battery as I can see you doing or my eyes are lying to me 🤔🤔🤔🤔

[@sangtearalte6969]

Type c working well??

[@stevemorrisby6705]

Flood soldering. That's what Motorola recommended on the 80s 2 way radios for removing hybrid circuits. There's nothing new there Your soldering iron should have a larger tip, but hey ho it works.

[@marinenav8]

What Liquit for cleaning?

[@j.caspersoundcatalyst2428]

Isopropyl alcohol

[@defaultuser0856]

1. Very inefficient 2. High probability that other components were damaged 3. Takes a lot of time

[@cre0308]

Please tell me wick name and solder name 🙏

[@j.caspersoundcatalyst2428]

Soldering wick and rosin core solder

[@mervinmorales288]

Hermano cómprate una estación de soldadura

[@Varmadheeraj6]

Super

[@jonybtw]

your face on the reflection😂

[@MmanzilsTech]

Hahaha

[@pclankatechnologies7764]

Super thx... 🇱🇰

[@Krystalmyth]

Sometimes the problem. with a charging port is the small board or ribbon it's attached to and this would be pointless.

[@ots-solutionOdisha]

I try this method but microphone damage this types of work

[@pem7195]

Muy buen video

[@ramadhananakboy2198]

Maaf bang itu tapi ngerusakk komponen yang kecil gak bang, soalnyakan kepanasann

[@daulatthakur1015]

RIP those phone who are dead after doing this

[@koseinwin8418]

Thanks 👍

[@MmanzilsTech]

Welcome 👍

[@SerenoOunce]

A basic reflow station goes for $50 now. If your doing this type of repair you have no excuse not to use one anymore.

[@R.M.L.M.Renewed]

A list of products? Am I missing it

[@bustakipchumba-kp5xv]

You might interfere with the ic nearby broo

[@VeLLaTv497]

Kali ko saf karne ke ly keya lagte hy

[@M.E63]

This wouldn’t work I guess on the Samsung Type C in the thumbnail

[@techyunboxinggaming7183]

Where do u live my redmi note 4 display connector is broken and I want to replace it

[@MmanzilsTech]

UAE Sharjah

[@DmitryMaster]

Если нет фена, то нечего строить из себя ремонтника и уродовать плату. Паяльная станция 20 лет назад стоила 100 долларов, теперь фен отдельно стоит в разы дешевле.

[@albertodiseno1973]

Muy bueno 👍

[@fsimoris]

Wrong ! You have to protect microphone ! 🤨🤨🤨

[@harpritsingh85]

Super duper

[@MmanzilsTech]

Thank you so much 😀

[@danishmuhammed4517]

It's maybe damage the print on the pcb.

[@cellphonerepairing2111]

Good methad

[@brizuelabrizuela7681]

QUE DESASTRE.....

[@matthewkenyon3011]

Where we going?

[@profixfrp]

Nice

[@idrusandrian2965]

Nais

[@mrshorts392]

That is painful to watch

[@remajapekalongan]

Poor solution

[@chai___219]

After this work you need to change a digital mic hhhhhh

[@mohammadhasan-lh7gn]

👎👎👎bad

[@АлександрПотемин-ы3к]

Обычно в этом случае дорожки тоже отваливаются... Отличный метод, если надо отклеить дорожки от платы... ))))

[@bhoot1702]

No it won't fall if you apply heat equally on all joins and contacts

[@medabfilms1]

Waste of too much solder😢

[@duke-ue5dg]

what????heat gun???? thats called soldering pencil not heat gun dzuhhh 👁👄👁

[@ArifBillahOnGoogle]

Easiest way to destroy your PCB

[@Daclaem]

brilliant

[@Munawar.127]

Nice trick

[@smashingmani420]

Paste konsi hai

[@j.caspersoundcatalyst2428]

Flux

[@EpicPCGeek]

Origin of the word "janky".

[@VK6TT]

Like your technique but the music puts me off

[@rfermin5041]

I have problem in mind meter the usb