How To Replace Channel Faders On Rane One DJ Controller !! Rane One Repair (Step By Step)

How To Replace Channel Faders On Rane One DJ Controller !! Rane One Repair (Step By Step)
LINK FOR PARTS (NEW FADER) instrumentalparts.com/channel...

[@dauseone]

Thank you for your great instruction. Couldnt have done it without you!

[@DJWHIZKID876]

bro thank you so much for this video. My left fader just died on me this week.

[@Thomas_Swift]

Great tutorial🎉 But my God that is like going back in the day and disassembling a dj mixer ( Gemini, Numark, Radio Shack, Gli ,etc. ) to loosen up the faders or resolder to get a decent cut-in time ( circa 1982- 1993 )

[@buddhapalmtv6878]

Thanks for sharing the knowledge my brother. Love to see more maintenance vids for the Rane One

[@KPCC74]

hey dj rock, wonderful video bro, been looking for this for some time. ⭐ ⭐ ⭐

[@djfamilysweden]

Wow great video.... this is too much job... anyway thanks 🔥

[@djt-why2316]

Thanks for the video, I just saved myself close to $500 for repair, cause repair shop quoted me a price for a whole board and labor, I rolled up my sleeves and made it happen, thanks for the walk through 👌🏾

[@djphunknasty]

Were you able to get these faders from InstrumentalParts? They tell me there's a current backorder, and I'm looking for ones that would work from elsewhere.

[@djt-why2316]

@@djphunknasty this is part with the CHANNEL FADER NUMARK N4 MIXTRACK II PRO II - III PLATINIUM FX QUAD VRS10304525

[@djt-why2316]

@@djphunknasty instrumental parts sent me a message, faders are in stock and shipped to me

[@AZTECHSOUL213]

@@djphunknasty They try to sell you the whole board. The ones in the link are listed as Numark but rockcee says they will fit since it's the same company.

[@phillipsimmons904]

Like I said before I know who to send my stuff to when I have problems! Lol

[@DJROCKCEEENTERTAINMENT]

Yes sir !! Anytime ! ✅✅✅

[@ranjitbhambhra5165]

I've just researched the rane one uses cheap numark channel fader which are on the mixtrack and N4, hope rane realises this. no wonder pioneer are the leaders in DJ hardware learn a less in music(RANE). Use good parts maybe you have a decent unit.

[@pedrolebron7546]

Thx for the video. It is a lot of work. How can I email you, I need mine replaced

[@BillyDee48]

Hey my brother the like you put up for the Rane one repair deck channel fader. the picture it shows is that one i oder cause i'm going to roll up my shirt sleeve to fix my Rane One channel faders

[@gamingheadztvMediaHeadztv]

Do u do mods like dropping in a innofader pnp for the up faders?

[@jel2106]

For a £1500 vinyl-based controller, having soldered channel faders like this is not a great design decision. I feel Rane could have put separate channel faders into the One quite easily - then the fader replacement would have been as simple as replacing the crossfader. I guess overall pricing was a factor.

[@ranjitbhambhra5165]

Right mate I've got one same problem as they use numark channel faders, I've got numark ns7 MK3 which is miles better.

[@djphunknasty]

This is great, but looks like a small nightmare to perform correctly without breaking anything or losing any screws or parts. The part where you suggest to video yourself is a great tip. May I ask what brand/model your desoldering gun is?

[@AZTECHSOUL213]

Yo, that link for the channel fader says its for NUMARK. When I asked instrumental parts for a part number, they sent me a link for the whole board with channel faders

[@gregorioavalos1256]

I need to do some troubleshooting. I have an intermittent problem with muddy sound. Not sure if it’s the channel faders, POT sensitivity, output signals? How do you know it is the fader?

[@djjo-z8870]

Dang this is a lot... my left upfader just stopped working. I've done fader replacing, but not like this

[@yemisafiu5891]

@DJ Rock are you able to give an advise on an issue I have with my Rane One if you don't mind? The LP/HP Knob remains activated despite the knob positioned back to the 12 o clock position

[@dabadoo7631]

Hey man, we just took a Rane apart to replace the Cue button as its not always working, we replaced it with a plastic button but it did not fix the issue It looks like it could be the electronic switch on the board, do you know if this is a common issue with a common solution to fix the cut button?

[@ryanprice6016]

Hey I have a serious inquiry about getting my my Rane one’s effects switch fixed. It popped offed and I would love to get it taken care of before this gig I have. What’s your shop name?

[@djcheseerg2228]

Saludos me gustaría saber si sabes donde comprar el conector USB de remplazo y el switch de efx te lo agradecería mucho ya que necesito esos dos articulos.. gracias

[@AZTECHSOUL213]

How many hours would you say it takes?

[@djnes2k7]

im good right up until the sodder part. i wonder can i buy that entire board with the faders already attached. My left pitch fader does volume and the ch fader does nothing. my right ch fader gets louder and lower whenever you touch it.

[@romeritorey]

how much is the cost for replace linefaders? as reference

[@vernonhenderson3845]

How long did it take you?

[@gullygutta7972]

How much do you charge to do this

[@johnpaulandrewcunanan1544]

My rane one fx paddle became loose, when i try to put it on the "lock" side it just stays there and you can feel that something came loose or broke off, is there anyway that i can repair this? Thank you

[@kazardancing]

hey the same thing happened to my controller, im wondering to i need to replace the board, the toggle switch, or just the knobs....im really hoping he will do a video on this......please respond if you find a solution.

[@ChristianJaeNYC]

@@kazardancingI have had the same problem you just have to replace the housing that holds the toggle switch in place. I had trub le finding the piece. It’s easy to get to if you take it apart no soldering anything

[@_P_M_]

There is a video on KZbin which deals with this using a hot glue hack.

[@erickonasis31]

props for the vid but no way in hell am i doing this myself

[@kysheemremix]

How do I get in touch with you?

[@joekoolz377]

My right side flex switch won’t lock when I flip it up.. would I have to take the whole thing apart ???

[@OBDPVCR]

Same

[@joekoolz377]

@@OBDPVCR S#!t is bs for how pricey the one is.. lever feels cheap like it’s unhinged and it could be a easy fix but this video.. smh .. to many screws ,.. I’ll probably sneeze and lose em all

[@OBDPVCR]

@@joekoolz377 it's poorly constructed and engineered. All the EQ knobs are not durable at all. 1 year in and I have problems with master gain, BOTH channel gains, the low EQ on the right side. My cue pads get trapped in the metal cutout of the controller and trigger themselves and now my left EQ paddle has somehow got loose and is unusable and more or less unrepairable. These things need to be easily accessible to repair/replace for any "pro level" piece of hardware.

[@michaeldawkins8493]

Same problem

[@nayahope5195]

Hi my right side platter just stop moving every time after 20 mins of playing time. The motor get stiff till I can’t turn it. Where can I get a motor to buy.

[@vernonhenderson3845]

Where can I buy the rane one channel fader?

[@djpharo9589]

Im Searching too !!!!

[@djpharo9589]

Do u Have idea where to find

[@tizzlevisionz550]

How do I get in contact with you?

[@Djantlive74]

Shop information pls

[@emmanvillaverde8073]

That is a lot of work , terrible design faders shouldn't be embedded in the board, my ns7 is designed better than that

[@georgebarrios9603]

I can't believe #1 that Rane put these faulty A$$ faders in this expensive unit, #2 They also put a faulty ASS Paddle Lens that breaks just as fast, #3 that you have to completely disassemble the WHOLE unit to switch out a fader. It's just NOT ACCEPTABLE at all! Shame on you RANE!!!!! 🤦🤦🤦🤦

[@HughDeLury]

Problem with this crap design is people keep buying it. Its the cycle. People buy garbage, manufacturers make garbage. They don't care! You buy it! Welcome to the 21st century! I work in the repair industry and this product is expensive, candy coated, crap but it sure sounds good, it looks good, and its from Rane so it must be good, right? RIGHT!? And about parts, is, don't blame repair techs when they can't find parts then charge you a pile because they had to buy entire boards. Rane, Pioneer, etc, do NOT make it easy to find a part because sometimes they just aren't listed, but we're thankful that some of you do the search for us and find out a Numark part works on Rane. I'm not taking that risk. if im wrong, guess who's paying? You... in case you didn't know. You are. And I'm not blaming you at all for being mad at that... its not my fault! But, I am not wasting my time on crap - which, unfortunately, is 98% of this stuff. So, budget twice what you pay for maintenance and like it. You'll have no choice.

[@DjNYTEE]

The use of drill is cringeworthy

[@HughDeLury]

agreed. never use a drill for these products. molded plastic with plastite screws means you beak a standoff or strip one in .06 seconds if you have the slightest hickup and you just ruined a thing. Get a good phillips set with a #1 and #2.

[@cuttinchops]

INMUSIC, STOP! STOP BEING CHEAP! Seriously STOP designing ALL your products like this!!! THIS DESIGN IS TRASH! At least give us socketed faders!

[@ranjitbhambhra5165]

This is rubbish same as ns7 don't buy these decks

[@prosperomon1424]

Please I have ddj-sz2 the red light is on but the rest light is off I really need ur contact please 🙏

[@DJROCKCEEENTERTAINMENT]

reinstall firmware !