How To Replace Crankshaft Position Sensor 2000-2005 Buick LeSabre

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@deivyleon409]

You don’t have to calibrate anything when replacing the cam and crank sensor for anyone that is wondering

[@timcountryman961]

I can't thank you guys enough for these videos. I've save a lot of money and built my confidence because of them.

[@Querencias7]

Beautiful job! Excellent step-by-step professional tutorial. Much obliged sir. ['94 Buick Regal 3.8L / L27 (very similar)]

[@jaredfletcher1587]

Would one of these going bad prevent the car from starting?

[@eileenheitman4351]

Outstanding explanation, demonstration, illumination. First rate. Thanks. Dave, not Eileen

[@brianfraser7822]

I have 2008 buick lacross 3.8 doing this very job know ,,thanks,,video helped completely

[@mikehicks65]

What is the proper relearn procedure ? If infact necessary?

[@markorkarenhanes1354]

If a person had to change the crankshaft position sensor, might as well change the camshaft position sensor too, while everything is apart.

[@josueletelier1745]

Muy bien video le felicitó y gracias !!

[@michaelwilliams7050]

Are you going to do a video on the 2009 through 2011 Buick Lucerne CXL 3.9 engine how to replace crankshaft sensor and camshaft sensor

[@SouthernBlessedHomestead]

Excellent video, thanks for the info.

[@mariadelia7945]

Can you use an outside puller that has hooks on the outside that grabs the perimeter of the harmonic balancer drum?

[@karafox7102]

What size of screws do you use for the puller

[@mlieser1230]

I've heard people mention 2 different sizes. 1/4 SAE or 6mm Metric. I believe they are metric. The puller kit should come with both SAE and Metric bolts.

[@jamespinckard4210]

Why would the crank bolt have to be turned another 76 degrees after reaching torque? Never heard that one before.

[@Whit_Siever]

Crank position sensor was replaced once for a small fortune at shop 4 years ago. Now having no start issues again. Swapped ICM still no fix. Question: Could leaking side cover/timing cover/water pump gaskets cause fluids to drip downward and short out the Crank Sensor?

[@TRQ]

+@Whit_Siever We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@jonthedon1618]

Do you have the part for that puller?

[@trentgrimes9880]

What kind of torque is needed to remove the crankshaft bolt?

[@griseldojamesnunez4154]

whats the breakaway on the impact wrench? Mine has just over 600ftlbs anbd the bolt refuses to move despite lots of penetrating oil.

[@stevewheatley243]

Dont simply disconnecting your battery relearn your sensors?

[@IiiIjj-tx3de]

Bro I have problem in my buick regal may I send you a video

[@supernintendo7579]

IS THIS THE SAME AS THE 2007 BUICK LACROSSE 3.8???

[@chuckddon3536]

Great video, thanks

[@JanielRamirez-rv3kh]

The online Manuel fir 2002 impala ls says 114 degress

[@vincegiltz2888]

You should NOT have lubricated the crank Bolt. When you do this you change your torque value. You think you might be torquing to 111 lbs, but now that you decrease the friction properties with the grease on your bolt you could have just increased your torque by 30%.

[@TRQ]

+Vince Giltz We appreciate the feedback. Sometimes there are multiple ways to accomplish the same repair. 1aau.to/m/Shop-TRQ

[@jerbburleson1]

I think I could probably do this procedure. I do not have a scan tool though. I notice you mentioned a possible re-learn procedure with a scanner. I know its hard to predict but what is the likely hood that the re-learn procedure must be done. Think this will determine whether or not I attempt this or not. And these videos are so helpful. Modern cars are wonderful but I don't think the engineers of them took into consideration that it would be a bunch of amateur backyard Gomer Pyle's trying to fix them .

[@TRQ]

+Jerry Burleson Thanks for watching. Buy the part in this video on 1AAuto.com: 1aau.to/m/Shop-TRQ

[@ashleychee1459]

Mr Jerry have u changed out ur sensor? I don't have a scanner also. I'm having 2nd thoughts about just throwing one on and hoping it works with a relearn procedure.

[@petrusc3384]

What is the reason for replacing the sensor?

[@brianfraser7822]

Changed crank shaft sensor,,,still just turns over,,

[@jerryburleson8604]

Fantastic!!

[@vulgervulcan]

Did everything exactly the Samantha my car won't start now