How to Replace Door Hinge Pin & Bushing Kit 1995-1998 Chevy Tahoe SUV

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@fredchalupa]

So, here's a little trick I learned in putting the new bushings in place. If you try tapping them in, you'll just break off the flanges, and fill up your swear jar. Instead, use a 5/16" bolt about 2.5" long, two washers, and a socket that is large enough for the splined end of the bushing to fit inside. Put a washer on the bolt, run it through the flanged end of the bushing, through the hole in the hinge frame, though the open end of the socket, another washer, and then a nut. Line it all up and slowly tighten the nut/bolt. It will press the bushing in place as slick as can be. No damage, no swearing.

[@hellhellya1]

Karl Stevens Or you can just grease them up and slowly work them in with pliers

[@dansloan4242]

Excellent!!!

[@Budster48309]

I just did the new hinge pins and bushings on my 2003 GMC Sonoma SLS. It was EASY! The only part of the job that was concerning me was the spring. I went to Harbor Freight, and for about $5 I bought a GM door spring removal tool (I've also seen them at auto parts stores for about $7) It made the whole job very easy. I opened the tool and pushed it into the spring. Then tapped it with a hammer until it stopped. Then just torqued down the screw and the spring came right out. It stayed there while I replaced the pins and bushings. When I was ready, I put the spring back in place and loosened the bolt on the tool and the spring went right back into place very easily the FIRST time I tried it. The tool made the job MUCH easier.

[@1AAuto]

Thank you for watching! 1aauto.com 888-844-3393

[@christophersawtelle2558]

Thank you for the good videos and especially ones using the 95-98 Tahoe. Perfect for my 97's. In the video you mention the bushings go to the vehicle side of the hinge but this is only on the top one. On the lower hinge the bushings go to the door side.

[@lightning0367]

I've got a 97 tahoe aswell. Been looking for videos on how to take off a door. And this helped me alot.

[@1AAuto]

@SRHDave13 If the pins are worn bad enough the could have a shoulder on them thta is holding them. Either use the jack to support the door in different positions or have someone work the door up and down while you are pushing them out. My best suggestion.

[@1AAuto]

It really helps to have someone help you with this job as the door can be heavy and a little awkward to work with sometimes.

[@ChrisPrkKy]

Thank You so much for this video!!!! My exboyfriend replaced my door pin on my truck 5 times and it still would not work right. From watching your video, he put the bushings in the wrong way and the top bushig kept falling down, so my door would not shut. Now I watched your video and feel comfident that I put the door pin in the right way and not have anymore problems with my door. Thank you for putting information out here on the web so people can do things for theirselves if they want to.

[@1AAuto]

@sylveskyl You may want to inspect the hinge itself or the holes in the hinge where the pins go through to see if they are elongated.

[@1AAuto]

@OTRdriver379 HI thank you for viewing our GMC door hings pin repair video. If we happen to do this repair in the future, we'll keep this request in mind.

[@FixingCrappyCars]

I usually have a pretty strict policy of not buying parts over the internet as in the past they have shown themselves to be of poorer quality. However, because i've used these videos that you make so much I think I will give 1a-auto a try. Keep it up.

[@mhkeiper]

Thanks! I feel like I can do this, where do I find the spring video?

[@dperez0706]

no joke if it wasnt for your channel i wouldn't have been able to fix my car with several things thanks 1a auto parts

[@1AAuto]

Thank you for watching. Glad we could help you out. Please let us know how the repair comes out! 1aauto.com 888-844-3393

[@dperez0706]

i fixed the rotor and distributor cap perfectly because of a different video! thanks a lot :)

[@ninjakittyboom]

I know absolutely nothing about cars, and your video helped me change out my pins and bushings without many problems. Apparently the right tools help, which I don't have, but it all worked out in the end. Thanks for the great Vid.

[@1AAuto]

We currently do not have an auto repair video that shows this particular repair.

[@1AAuto]

When replacing the motor mounts on the suburban, you have to have a way to support the engine as well as lift up the engine to remove the old mounts and install the new ones. If you feel this is something you are not capable of doing on your own, it would be in your best interest in having a mechanic.

[@1AAuto]

We currently do not have one for that particular application. We'll keep this in mind in the event that this repair needs to be done in the future.

[@1AAuto]

If the door is now tight when you pick up on the bottom of it, check the hinges to see if thery are bolted into place and allow for adjustments.

[@keithramsey3795]

i would like the video om how to install spring.

[@blackie361855]

Special tool

[@1AAuto]

@iamchevyman5 Thank you for visiting our channel. If you ever have an issue with a part you have bought from us, we're here to help you out. Have a great day.

[@1AAuto]

What series is your GMC Sierra.

[@doodah2475]

Thanks for leaving out how to do the spring part of it.

[@duaneadams7068]

Thanks! The video was very helpful. The use of zip-ties to keep the spring compressed while reinstalling was especially helpful. I initially tried to use cheap Walmart zip-ties but they wouldn't hold. I found heavy duty ones at Lowes rated at 75lb. tinsel strength that did the trick. I also found it helpful to loop the ties completely around the spring (end to end). It gave more compression and made it easier to get the spring in place.

[@1AAuto]

@quillfam The should fit with little force. There are different sizes for different holes.

[@1AAuto]

@stormer1092 You could try to use some white lithium grease on them.

[@jamescone6359]

Nice view of your shoulder and head

[@1AAuto]

@i13w13d The general idea is the same but there may be some differences. I have added a sunfire/cavalier to the request list.

[@1AAuto]

It all ranges because different dealers have different labor rates. I would try finding out what the hour rating is on this and then find the dealer with the best labor charge.

[@1AAuto]

@bluetickrunner You can do that but you need to disconnect the harnesses.

[@1AAuto]

The issue might be related to the hinge not working anymore. There could be an issue with the pins not holding anymore or could be bent.

[@1AAuto]

You may need to either replace the hinges or weld a little material back around the hold opening to make it smaller.

[@1AAuto]

You may be able to apply some of the basics shown in this video to your application.

[@NashvilleEar]

Thanks guys! I have to replace a door on my daughters car. I found a used door on ebay, so I will do what you guys did and put on the new door with a new set of pins. Can I buy new pins and bushings on the internet? You have made my day guys! Thanks again!

[@1AAuto]

We currently do not have an auto repair video of that particular repair. We'll keep this request in mind in the event that we need to make this repair in the future.

[@cameron6783]

I have a 2003 chevy s10 4x4. How do i replace the rollers on the other pin aswell? Very helpful video btw.

[@1AAuto]

We currently do not have an auto repair video that shows this design.

[@1AAuto]

@Snookieannhuggels Yes this part is the same on an 00 escalade as it is on a 1992-99 Tahoe or Yukon

[@1AAuto]

@doulos4JC Yes I believe you can do just one at a time, but usually if one is worn they both are.

[@AP9311]

I found this vid very informative! as I used this to replace my bushings and pins. saved me alot of time and money! and my door shut perfectly and did what its supposed to! love it!

[@Weaddor]

Thank you kindly for the video. Replaced both hinge pins today within 1 hour, couldn't of went any better! Great video.

[@1AAuto]

+Scott S Congratulations on the successful repair. We're glad the video helped you out. 1aauto.com 866-403-3393

[@goejeni]

hey mike, i watch your videos all the time. on these doors what hapens when the hinge holes have become elongated? and do the doors on these trucks leak water from the seal when the hnge becomes bad? thanks for your time

[@1AAuto]

Have a great day. Thanks for watching.

[@1AAuto]

You may need to replace or repair the hinge if that's the case.

[@gholt71]

Have you ever replaced the hinges that are not bolt on? I'm looking for a way to repair my worn out hinges. The pin bushings do not last very long with elongated holes. What do you think about welding the worn side of the hole and then grinding it round again?

[@reptigod]

Any advice on my door hinge pins being seized in there? Or are they not coming out because I'm not relieving the pressure on the door by jacking it up?

[@willie201000]

these videos are great mike. I was wondering though, wouldn't replacing each pin one at a time eliminate the need for a helper?

[@lukiss01]

Lol good idea. Seems most logic

[@davemblover69]

about to do mine, but i think that may not work because have to seperate the hinge to get bushings in

[@bigvosh]

Great insight - 2001 Jimmy is a bit different, but the basics are the same. This video helped me a ton!

[@E1VM]

Can you do the replace the upper rod then take out the old lower one and replace that one so you don't have to worry about the door support so much?

[@64shovelhead1]

Hello everyone. any advice on what to do if the holes that the bushings are supposed to go into are egged or worn out. when I try to put the bushings in, it forces the bushing towards the oval side and cracks bushing. Hinges are welded in....no bolts... cut and replace???? or is there any other soloution? thanks

[@drwombat]

Hi please link the Video Reply that shows how to install the spring, I did not see it linked in the section below video info where you mentioned it would be in the video.

[@Luke05050]

The link in the description says 1992-1994 Chevy Blazer Door Hinge Pin and Bushing Pair (front doors). Will this fit a GMC Sierra? I can't search for anything before 1999 on the 1aauto web site.

[@stormer1092]

I replaced my pins on my drivers side about a year and a half ago. Well they are already shot. Any grease or special lube you could use to keep them from wearing so fast?

[@jjtransman6353]

Hi Mike, Great video! Thanks. But I was wondering about something that goes hand in hand with the hinge repair and that's' the door latch. I have to repair the hinge on my 99' Suburban but the striker and latch are damaged as well. The striker is easy enough but can't find the the equivalent GM 16631627 part in aftermarket anywhere. Does 1AAuto carry this part??? Hope you can help!

[@joshuamedina8920]

do yall have this video for 2008- 2014 tahoe ??? my door has horriable noise and door hard to close

[@1AAuto]

Its the same concept but this video is for the older models.

[@lobsterboltns9831]

Great video - but both of my lower door hinge bushings on my 97 GMC K1500 were on the door itself. Just a heads up.

[@XFHgog]

That's the way it goes. The bushings go on the door side on the bottom.

[@paulsears775]

Same story with my 99 K1500 Suburban.

[@53tominator]

I have the same vehicle. Should I put the bushings on the door hinge itself or do what mike said in the video, by putting on the hinge closest to the vehicle?

[@mattraumikaitis8405]

Do you have a video that shows that same breakdown for a 2000 to 2006 GMC Sierra? The door pin/hinge configuration is different and access is difficult because of the configuration.

[@teslanik]

thank you for an informative video! I do have one question though. My door sags so bad you can barely close it. Also, the spring itself came out and the pin the spring rests against is bent. If I just change the pins and leave the spring out, will this solve my door closing issues?

[@danielzubarev6905]

If want to replace the whole door is there the easier way to remove it, or I should do the same thing?

[@harlyman2011]

are the pins for the front and rear doors the same? all the part stores i call only have listings for cargo and front doors

[@bsbru88]

@1aauto Do you have a video of this procedure for a 1999 chevy silverado with the new body style? Also, for the third door pins? Thanks.

[@brandonbsw18]

What about when the holes on the car end of the hinge are all wore out and are oval shaped? When I tried installing the new bushings, the holes were so worn out that the bushings were too small. Would I have to get new hinges? If so the hinges on my '96 GMC Jimmy are welded to the car, how would I go about getting those replaced?

[@doubleblackD]

Thanks for the video. Only problem I ran into was the springs. Did you end up making another video in regards to putting the springs back in? I tried many different tools (pliers, vice grips, etc.) but to no avail. Thanks again.

[@graffist1]

I need a detent pin for my 2001 gmc jimmy. But not having luck finding it. Would a chevy pin same year work. Any help would be appreciated...thanks

[@OlAbeLincoln]

you said the bushings go on the car side of hinge, but on the bottom pin you put it in the door side and the top you put on the car side?

[@keepthelikesat710]

How do you replace the other pins, the ones that are more inside of the truck or what part that's called. Mines are startin to bend

[@salonchick03]

Im having a problem finding how to replace a split hinge pin for a 2000 GMC Sierra, other videos and this one only show one piece hinges which is not what I have. Any ideas how to do this?

[@ashure36]

@1aauto yup, I found it right after I posted this comment. I almost did this very same trick with some wire but couldn't get it tight enough, the zip ties looks much better. Thanks for the awesome vids.

[@duanejames5617]

Do you guys have any videos on replacing the whole door hinges? The oem type hinges. Thx

[@1AAuto]

+Duane James We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1AAuto.com

[@Barry11997]

Thanks man for taking the time to make these videos you’ve helped me out on many projects.

[@1AAuto]

+barry cowan Thanks for checking us out. 1aauto.com

[@Barry11997]

Good lord yall never said it was that difficult and its gonna have to come back out im gonna have to get the oversized bushing. That guys a bad ass he did all that himself im impreased

[@rosbrughjb]

I bought the parts from you all through your website and will install this weekend!

[@auxmike]

Do you have a video like this for ford mustangs?

[@lutz7001]

do you have a video of the other upper pin with the roller? or do you sell those I have a 2000 escalade and 1 of them pins broke. any help will be appreciated. great videos by the way always helps when I'm stuck with a project.

[@1AAuto]

+John Lutz We currently do not have an auto repair video on that particular repair. Thank you for asking. 1aauto.com

[@ashure36]

how do you get the spring back in?? Great video's.

[@apcaputo]

Will this same video work for an 2005 Silverado?

[@tonyhughes5406]

Dow you have a video on the door hinges replacement 1989 chevy truck

[@1AAuto]

+Tony Hughes We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-1AAuto-c

[@bigboyinthe5016]

My springs are gone but I'm glad...I think they contribute to the bushings and pins wearing out

[@1AAuto]

+Kamikaze_ Mike Thanks for the feedback!

[@bigboyinthe5016]

@@1AAuto you bet... You guys made some decent content on these rigs....have to re align the 3rd door soon....pins are solid but it's not right....doors been changed so I figure the hinges are bent....any vids on that??? Have not found much on the 3rd door

[@1AAuto]

We currently do not.

[@israelgeddes604]

Definitely. So much easier with a helper!!!! It's extremely difficult doing this on your own!!!

[@MsBdotSmoove]

Do u have a video showing us how 2 replace a whole door? Great vids by the way!

[@billybillo9998]

How do I find a video on the back door rollers. I have a 98 burban.

[@1AAuto]

+billy billo Great question! Check out our library for more videos here: 1aau.to/m/video-library-c

[@dansloan4242]

I noticed in the link that's attached to this video, that there are no keeper rings for the PIN??? How can this be, when you're going to destroy the factory ring that's on there, when removing it! Thanks

[@BrandyAmberAndrew]

Thanks!!, how about the roller pins?

[@1AAuto]

They could if the doors do not line up properly.

[@Snookieannhuggels]

do you have one for a cadillac escalade 2000 ?

[@yohon1550]

I am left wondering it it would not be beater to do one hinge at a time, So you dont need to put a jack under the door and maybe not need a helper. I have never done this so I do not know. if you have done this tell me this is not a better way.

[@markmunnsr2558]

You should have shown how to place that spring back in! The spring is very critical plus difficult.

[@anthonyherrera4303]

Want to see the video installing the spring

[@rossmunn9770]

I like your video good detail and instruction. I've got to removed my passenger door on my '96 CK1500, cause I ran into a small post in a parking lot. Boy, that's a downer. Thanks for the info. I'll be having this with me when doing the job!!!

[@victorandrade818]

Do you have the link for the springs? That the video talked about

[@1AAuto]

+Victor Andrade What is the year, make and model of your vehicle. I'll see if we have them for you. Thank you for asking

[@redferngrows3917]

hes talking about the link on how to install the spring back in the door

[@1AAuto]

No unfortunately it sounds as if you have more issues with the actual hinges and will need to replace those too and not just the pins.

[@07032563]

Good trick when doing this is to roll the window down. Not only will you not hit it with anything but you have more options to hold or grab from.

[@MRYOUNG702]

@1aauto is it possible to do 1 hinge at atime if I don;t have a helper

[@HitemWithTheFlex]

Just did these on my 95 C1500, the bushings go in differently than this video. The top bushings go into the door frame, and the bottom pin bushings go into the door. But everything else was the same.

[@1AAuto]

You may be able to apply some of the basics to your vehicle (depending on how the door pins are made). It helps to have someone hold the door steady, and to use a floor jack to keep the door propped up so that you can service the hinges. 1aauto.com 888-844-3393

[@irish56e8]

Can I have the video clip that shows how the spring in reinstalled? thanks

[@1AAuto]

@ashure36 Search My videos for "install hinge spring" and you will find it. I actually have too many videos and cannot attach it to this one.

[@1AAuto]

Here's a link to the video that shows you how to replace the door spring in your Chevy Tahoe kzbin.info/www/bejne/hn6pq4Oubtlrm8k

[@ronaldcrawford2258]

Link don't work

[@Redsox3600]

Do you know how much the typical dealer would do this job for?

[@wardlawsg1]

Hi i have a 2003 Chevy blazer and this morning my spring popped out this morning and now the door is off track and the guy was like they need to re-weld the door hinges instead of just replacing the pins and bushings. I just want to know is this something that needs to be done or i can i just replace the pins and bushings myself and re-install the spring.

[@1AAuto]

If a qualified auto body shop or mechanic gave you that advice, you may need to have it welded back in place. It's a common part to fail on those vehicles.

[@mfe1896]

1A Auto Parts great video like always but do you have a video on replacing door hinges on a 1999 nissan maxima gle..dont think i can just replace the bushing and pins think i got to replace both top an lower hinges on driver side..thanks

[@1AAuto]

mfe1896 We currently do not have an auto repair video that shows this particular repair. We'll keep this request in mind in the event that we need to make this repair in the future.

[@daniektrevi3885]

You can make a video of a 1998 Chevrolet Silverado 2500 two doors, it is almost the same as the one you have in this video. The a / c does not blow much air through the vents, the blower is very loud below, but very little air comes out. I think the filter is clogged. Can you show me how to repair it?

[@1AAuto]

+Daniek Trevi We're always cycling through common cars. We'll add this repair to our list! 1aau.to/m/Shop-1AAuto-c