How to Replace Electric Fuel Pump Sending Unit 05-10 Chrysler 300

Buy Now!
New Fuel Pump Module Assembly from 1AAuto.com 1aau.to/ia/1AFP...
1A Auto shows you how to repair, install, fix, change or replace a broken, damaged, worn out, faulty or shorted out fuel pump sending unit. This video is applicable to the 05, 06, 07, 08, 09, 10 Chrysler 300 with 18 gallon tank.
This process should be similar on the following vehicles:
2005 Chrysler 300
2006 Chrysler 300
2007 Chrysler 300
2008 Chrysler 300
2009 Chrysler 300
2010 Chrysler 300
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oi2/1AX...
• 10mm Socket 1aau.to/ohx/1AX...
• Ratchet 1aau.to/ojL/1AX...
• Hammer 1aau.to/oce/1AX...
Subscribe: / @1aauto
Check out our playlist:
Chrysler 300 2005-10 1st Gen: • Chrysler 300 2005-10 1...
For More Info visit us at 1aau.to/h/up/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@TroyStevensStelzerPaintingInc]

What about the auxiliary fuel pump module on the passenger side? How do you know when that needs replacing? How can you be certain it's the primary fuel level sending unit and not the auxiliary module? Why aren't there any videos of it?

[@MariaRodriguez-qp5ir]

Thank you so much for your excellent video! I lost my husband to covid in 2020 and I now have to do all the up keep on my car myself. I have a 2006 Chrysler 300. Money is so tight to say the least, but it feels good to learn to do as much as I can myself. Your channel here as given this 58 year old woman an I can attitude. Thank you!👍

[@alemartinez3149]

Thank you so much! This video is really useful!! There aren't many videos about Chrysler 300 05-10 it helps a lot!!

[@1AAuto]

+Ale Martinez Thanks for the great feedback!

[@aftabnuraney504]

This video was right on point. The step by step was easy to follow for my 2005 Chrysler 300 Touring 3.5L. My only contention overall was attempting to release the metal ring. It took me almost half an hour but they conveniently cut this to only 10 seconds. I usually pay someone to work on my car but this video was eye opening and gave me the confidence to DIY. Whole job was no more than 60 minutes. Thanks 1A Auto! Keep up the good work.

[@tonel383]

Was your gas gauge not working?

[@thrashingmetal]

There is tool on amazon for 17 bucks yo open the ring

[@beebo5150]

Hello, I didn't think I could do this on my own, I almost gave up trying to take off that plate lol! But I got it off and your video made it so easy for me, much appreciated 🙏🏻

[@SupaNOVAent561]

Only thing I wished he’d mention in the video is that a fuel pump lock ring removal tool exist. I spent an hour trying to chisel that ring off the pump with 0 success. There’s a $4.99 tool at Oreileys Auto Part that mix it WAY easier. And chiseling metal next to all that fuel risking a spark doesn’t seem to be the best move lol great video tho 👍🏽

[@marcsmith5793]

Got the part # by any chance ? Mine just went out on pump 4 at the gas station right now

[@SrtLv4x]

Thank you so much for this! Mine just went out in the parking lot of a Walmart and i thought something was wrong with my engine😭

[@juanvillegas1435]

awesome video . saved me hundreds of dollars. just make sure you're gas tank is almost empty before opening it. yes , im a beginner lol

[@justinkillings5689]

Thanks for everything once again 1A Auto. I had the fuel pump swapped out in about 45 minutes after watching your video.

[@1AAuto]

+Justin Killings Thank you!

[@thrashingmetal]

How many miles your pump got ?

[@raleighrealrite6623]

Your video is the best put my pump in today by myself witch i know nothing about cars thanks my man on god

[@1AAuto]

+mari miller Thank you for your positive feedback!

[@marcsmith5793]

Mine just went out after getting a full tank of gas right now in my 06 300c, this is a life saver.

[@leewerner4831]

thank you for the video. the 300 is back in action

[@ibrahimgaming4066]

Thank you for showing how to install the fuel pump. Great work. I love your parts

[@candacebenford1734]

Excellent video as always! Thank you

[@CLINT_theNotorious_TTG]

Thanks A1Auto for the helpful videos! I probably saved a $1000 total doing repairs myself after watching A1 vids. 😃👍👍

[@1AAuto]

+Clint -n- Thank you so much! We are happy we are able to assist you.

[@damianrodriguez2140]

Yes thanks you 1A Auto I have. 05 300 touring you have officially help me with my fuel pump and to forward with my project car

[@divinemotorsports]

Followed step by step for my 2006 dodge charger rt. Worked perfectly. Thanks!!!

[@mxharescrambler6612]

Same for the SE? probably?

[@stelios777]

Informative and to the point. Thank you.

[@eltrillo3889]

Do you guys have a video on replacing the secondary pump, placed on the right side?

[@jbanderson5123]

Thanks for this video it really helped a lot

[@winningside1]

Give this man a promotion 👍

[@1AAuto]

+Oscar Lopez Thanks for checking us out. 1aauto.com

[@AlazeLuxxx]

Got it done! Thank You!

[@fbbc6495]

Allright thanks my car is starting to surge and I thing it's the pump, good video

[@typicaltilly2535]

How do we know which side is the problem though? Left side or right?

[@harriscruickshank1857]

Thank you so much guys.

[@LDBoone]

thank you for a great video. very informing. walked me right through the process. A1 job

[@1AAuto]

+Larry Smith Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c

[@Petrolhead350cui]

What is the reason to replace the pump? Stalling? No start? What happens when the pump has to be replaced? Love your videos guys.

[@raleighrealrite6623]

Car wont start shuts off where ever your at.

[@samsen201]

Usually when everything looks like fine but your car suddenly stops in middle of road or sometimes rough start (At beginning) are indications of bad pump (Not a totally dead pump). A lot of mechanics may suggest various things and you ending up many bills before the real remedy as in general, this does not turn in an error in OBD but your old car probably has something in store that drives the novice or crock mechanic in a different direction, initially. If in doubt, do a pressure check or even better, change the pump and go from there. More likely than not, your problem is solve. Other problems such as bad electrical connection, dirty fuel pump, regulator's vacuum valve diaphragm leak or fuel injector leak are fare less common.

[@SerenoOunce]

Car may not run if you pull the fuse/relay first. Disconnect them while the car is running so more fuel will drain from the lines as the engine sputters out.

[@henrygmz141]

This guys are amazing...👍👍👍👍

[@DPH1301]

Incredibly easy, hardest part to do for me was not get a drop of gas outside the tank, I spilled about 5 tablespoons full, entire work time was about 20 minutes from start to finish...

[@1AAuto]

+DPH1301 Thanks for checking us out! 1AAuto.com

[@YoungPrincinho]

I replaced both of my fuel pumps and I still got the check engine light saying that it’s my fuel sensors level. I don’t know but the light doesn’t want to go away. Also, my gas gauge move up and down so I really don’t know when I have gas in the car. Do you know why ?

[@Jujuandpaw]

Was told that I needed my 2005 Chrysler 300 fuel pump module assembly replaced and it was about 3 hours labor and $700! Is this the same thing?

[@ntroxell83]

Its amazing how easy u make ut look I guess ur lock ting us clean n not rusty ir dirty so urs comes out easy u need tell peopke also if u hav kids vacuum up ne degree under seat n dirt around the fuel pump so u dbt drop nething n that hole when u remove

[@hackysmacky]

well done, great video! thanks

[@1AAuto]

+Dream Tube Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/electric-fuel-pump-and-sending-unit-module/i/1afpu01344?KZbin&CTA+Comment&AScUmMs4h4

[@hackysmacky]

1A Auto Parts thanks for that link, my car uses the 19 gallon its 5.7 v8. Would that pump work?

[@68camarorsss33]

Dream Tube No I'm 99% sure you need the pump for a 19 gallon

[@scottmurrell8769]

Would this be the same process for a 2003 chrysler concorde. I didn't see an access port in the trunk but haven't looked under the rear seats. Or will I have to drop the fuel tank.

[@ishish9283]

Where is the fuel filter on this particular vehicle

[@JohnElHanafi]

The only comment I have is the use of paper towel to clean out the fuel on the sides; I felt like the technician was pushing the contaminants back into the fuel tank. Maybe it's just me but overall an awesome video!

[@1AAuto]

Thank you for the feedback! +John El Hanafi

[@JohnElHanafi]

Thank you for all the awesome videos! They sure are very helpful!! @@1AAuto

[@LinoelFelinoOficial]

Hi, awesome video very helpful, but how can i know if my tank is 18 or 19 gallons?

[@1AAuto]

+Lino el Felino If you are unsure I recommend getting in touch with your local dealership with your VIN number. They should be able to tell you the fuel capacity of your vehicle! www.1aauto.com

[@LinoelFelinoOficial]

Thank you guys!! 🙏

[@michaelreynolds6414]

Super simple

[@mariposanegra3048]

Thanks

[@dalemccord2129]

2:00 Main disassembly starts

[@89purpz]

I’ve noticed that there are two fuel pumps for the dodge magnum, What is the name for the part behind the passenger side?

[@pkranz937]

Driver side is Primary, Passenger side is Secondary

[@johneffrig9824]

Crossover is what you call it

[@jguerrero1972]

exelent video thanks

[@luisrodrigue4560]

mejor esplicacion que eh visto. gracias

[@1AAuto]

Con mucho Gusto!

[@shannanschisler8485]

On the Avasva you can count on professional help with problems and technical support.

[@felixlol793]

Does the fuel pump come with fuel pressure regulator inside or would that be separate ?

[@juniorgambini]

Hi I have a 2005 Chrysler 300c the fuel tank size is 19 gallons and the fuel pump says 18 gallons is that ok to purchase

[@jayyayy3203]

Is this the fuel pump or fuel pump sending unit? Mine code saying fuel pump sending unit side b but when I look it up I thinks it’s the passenger side

[@bear4815]

So I changed the fuel pump perfectly fine, but my gas gauge is not fully reading the amount of gas and I have in the tank correctly couldn't be a huge that is out for me to be replaced?

[@xaviergarcia6451]

Is it the same to replace a 300c 2005 Chrysler ?

[@14dogday]

I have a question...what side controls the fuel guage...I changed one side, the driver side. Fuel guage still reads wrong...why does the other side have a float

[@juan10sara]

Is it 100 percent necessary to take the fuse out. If so why?

[@liddoraskal7274]

Would this be the same process for a 06 300c SRT8?

[@tragetbase]

Where is the fuel filter located ??

[@johnmaxx4818]

I use a brass punch,no sparks

[@quetzalcoatlazteca8774]

I have a question where the fuel filter is located in a 2005 chrysler 300c thank you.

[@ericbryant796]

There is a tool available to remove that ring made for a Chrysler that you can get on Amazon...a bit easier than using a chisel and hammer....safer too.

[@firearm.obsessed8142]

If you unplug your battery dont close your trunk unless you have a key that works on it cuz I had to RIP my seat out to get into trunk today at Walmart lol

[@kyledakilla8724]

My new fuel pump just keeps running. Will it eventually stop?

[@bentacular9545]

Do you have to have a empty gas tank to do ?

[@neilnguyen2512]

Please quote the cost to replace the fuel pump ! Can you do it in INGLEWOOD WA 6052 !

[@Seb726Laviolette]

How do i know wich side fuel pump is bad? There is 2 of them under the rear seat?

[@isaactandoh1889]

This works for dodge Magnum too right?

[@donnelljefferson4161]

Aftermarket replacements are terrible! I have replaced over 3 pumps and filters. I just go to the junkyard and get a $40 replacement from a Chrysler 300, Dodge Magnum, Challenger and Charger. Most of the aftermarkets only have a one year warranty. Life time warranty is the only one's i consider. Having gas levels below a 1/4 tank wears out the motors.

[@Jujuandpaw]

Hi I was wondering if changing the fuel pump will fix this problem. My fuel gauge just started being stuck below empty then occasionally going to the correct fuel level and then back to empty when I start the car again. Could that be the problem?

[@1AAuto]

+Gregory We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@lilyh4028]

So after replacing the fuel pump, my gas guage isn't reading properly.

[@SerenoOunce]

Common issue with the budget aftermarket pumps. These are essential parts so shell out for a name brand

[@Moorenorfolk]

Hey how long should it take to prime?

[@hotrodr8rn8njoshuagerdon19]

Hey can't find a video of you guys changing a starter in an 05 Chrysler 300 touring. Need to know if that's why my car started up 2 times and died then hasn't turned over since. The battery and fuses and everything is fine so I think it's the starter

[@1AAuto]

+Tison Raider We currently do not have an auto repair video for this particular year, make and model vehicle. We will keep this request in mind in the event that we need to make this repair in the future. 1aauto.com

[@freakzalez5073]

Replaced fuel pump on 2007 chrysler 300 3.5 touring, still won't start Got code P0007 fuel shut off valve which should be on fuel rail which is not. Where do I go from here

[@8585cpimentel]

VERY HELPFUL.. TNX. NEED INFO/HELP FOR THERMOSTAT REMOVAL ON THE SAME CAR.

[@1AAuto]

+Christian Pimentel We currently do not have an auto repair video that covers this particular repair. We will keep this request in mind in the event that we need to make this repair in the future. 1aauto.com

[@8585cpimentel]

1A Auto Parts Thank you

[@gregsarro5839]

Can you do a video on the auxiliary pump fuel level sensor check engine light code comes on and off and gas reading fluctuates so im replacing both pumps thanks

[@1AAuto]

+Greg sarro We're always cycling through cars filming hundreds of common repairs for common vehicles every month. We'll add this to our list of repairs to film. Check back again and hopefully we'll have it soon.

[@gregsarro5839]

@@1AAuto should it be the same way as the main pump

[@moparrdudee87]

I don’t see a pump for a 2010 Chrysler 300 S with the 5.7

[@GabrielGarcia-jz8pq]

man i watch this video 2 x back to back & went out & for my 1st time it went exactly like it showed just the plate a little harder to get on then take off jajajajja but (,

[@timdinges9850]

How does that quick conmect come off? Terrible camera angle, and it's the hardest part to disassemble.

[@samsen201]

I wish my GM Yukon had an access service door like this Chrysler. I have to drop the gas tank that is currently full (30 Gallon) and burning the fuel as you suggest, is not an option. Only if I could figure our how to empty it peacefully! And many say, only drop one side to reach to top of tank and detach the connections to remove old pump but I doubt this will work with me... Any suggestions (Beside giving the car to cheater mechanic or dealer who want more than a grand to do the job!

[@1AAuto]

+Sam Sen We currently do not have an auto repair video that covers this particular repair. We will keep this request in mind in the event that we need to make this repair in the future. 1aauto.com

[@calicolombia102584]

why my 2009 chrysler 300 still shakes after I install all new spark plugs

[@krazmex09]

Hello im having trouble with my charger turning off once tank goes half way. I took it to a shop and they told me its sending unit. Does it sound right? Jw and maybe a dumb question but is it only one sending unit in car? Im asking because it has two pumps

[@1AAuto]

+ANGEL AVINA We currently do not have an auto repair video that covers this particular repair. We will keep this request in mind in the event that we need to make this repair in the future. 1aauto.com

[@pkranz937]

Both pumps have a sender, and the ECM compares the two and determined the fuel level. If you start with a full tank and it craps out at half full, your primary (driver side) pump is dead, and should be replaced.

[@jamesholloway4755]

I did exactly what the video did and car is runing but gas gage keeps going up and down anyone know why?

[@igotitonmyownb9553]

James Holloway your float or sending unit may not be working correctly

[@jaylovinpoo7582]

Hey having the hardest time getting the lock off any advice or where icould buy the tool to get it off easy

[@1AAuto]

+Jay LovinPoo Thanks for watching! As you can tell by the video the lock ring is not the easiest thing to get off. It can be pretty finicky. I recommend trying to apply a small amount of penetrating oil (WD-40 etc) to try and loosen up the ring. There is no special tool for the removal of this part, just be persistent and don't hammer it too hard!

[@bobbytee8599]

@@1AAuto There is actually a special too to remove this. Part number is OTC6599. www.amazon.com/OTC-6599-Universal-Fuel-Sender/dp/B000F5LJ7S

[@timhanna870]

If only the lock ring was that easy.... am I missing somthing

[@steveg9302]

Does the fuel pump have the fuel filter in it?

[@MarcyMckeefer]

Did you ever find out the answer to this?

[@cristiannieto8791]

Changed my fuel pump and my car won’t turn on now. It was running great before, it just had a bad gauge to where when it reached half, my car wouldn’t start. Now my gauge reads half of gas in my tank but it won’t start. I followed the steps and I let it prime and still nothing. Please help. Thanks .

[@1AAuto]

+Cristian Nieto We wouldn't be able to diagnose an issue like that, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1AAuto.com

[@johnydub7346]

Maybe ur fuel pump defected

[@guillermomarquez547]

Do you guys sell that electric connector

[@1AAuto]

+Guillermo Marquez Thank you for your question. We typically sell the pump or the fuel pump assembly with the electronic connector.

[@firearm.obsessed8142]

I took my relay out and tried to start car for like 15 mins and it's still spews a bunch of gas out

[@starwarsempirestrikesbacks182]

What does he mean by turn the key to the run position

[@1AAuto]

+Star wars Empire strikes backs Turn the key to the on position, but not so far to start the motor. This will allow the fuel pump to prime.

[@starwarsempirestrikesbacks182]

@@1AAuto thx

[@abstraddic0442]

Is it a fire hazard to put electrical wires into an automobile gas tank that's filled with gas and then reconnect your battery with gasoline gloves on? Cross your fingers and turn the key to the on position? I'm feeling lucky

[@thrashingmetal]

In thermodynamic the mix fuel air spark needs to be at specific level to lit a fire.. it's too rich to fire no spark inside the tank. .. engineers know these stuff

[@lololucero1]

Thats not the sending unit is there a video on replacement of the sending unit behind the passenger seat?

[@1AAuto]

+Lolo Lucero We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1AAuto.com

[@cremeuseoldrs981]

This is the code p2067?

[@ntroxell83]

Mylar is 06 n it foes not have that piece ur tapping on its got some lil metal things that ate bent over n its not coming off that way

[@brianmoody996]

Is this the same as a 2008 Chrysler 300c

[@1AAuto]

+Brian Moody We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application. Hope this helps you out

[@pkranz937]

2006 - 2010, same for 300/Charger/Magnum/Challenger 2011 - 2014, same for those years 2015 - 2020 Same for those. Each engine has it's own specific pumps, so you have to get the right year and the right engine.

[@olympialong6119]

I have a 300 Chrysler do we have 2 fuel pumps

[@fabianespinoza5610]

Olympia Long yes one on left and right side

[@mustafalafta4315]

How much dose that cost in Labor?

[@1AAuto]

+Mustafa Lafta Thanks for checking us out! The rate of labor varies from shop to shop so we wouldn't be able to give an estimate on that. If you have the tools and time, this video should be able to walk you through the install. You can also give a call to a local shop and get an estimate from them.

[@ashmax6120]

40 min in, still can’t get that metal ring off

[@realistmw]

It has two pumps tho

[@cashinginonusedcars3911]

Can't see how to get the fuel line disconnected your hand was in the way. Very critical not to break it. If you dont know where to pry or press on the disconnect you can break it. Video is worthless without the most critical part to get the pump disconnected !!!!! Hello !!!!

[@colbyshyne803]

2:37

[@ricosuave2934]

I purchased fuel pumps for my 2006 Chrysler 300. You guys sold me a defective fuel pump. The harness on the fuel pump was not the right fit. Had to use old harness. The gage doesn’t work properly. Don’t know if I am low in gas. I provided the vin number to make sure the correct fuel pump was installed . Email your company. They requested for me to send them pictures. Didn’t seem like your company wanted to take ownership of a default item you sold me. But made money selling me a defective fuel pump. Will never purchase anything from your company.

[@johnhut8088]

My fuel gauge is reading empty after install and I have a full tank of gas

[@1AAuto]

+john hut We do not have a way of being able to diagnose the issue that you are experiencing with your vehicle but suggest taking it to a local mechanic for a proper diagnosis.

[@linomendoza7405]

Yea I have the same problem with my car

[@shawneeeiy]

It looks too easy