How To Replace Front Coil Spring On Bmw X1 (2016) - 2023 Guide

[@gibingeorge88]

Is this coil spring suitable for Mini Cooper

[@SanuMotorswithCharlie]

Replacing the front coil spring on a BMW X1 (2016) involves a series of detailed steps. Here’s a comprehensive guide: ### Tools and Materials Needed: - Jack and jack stands - Wheel chocks - Socket set and ratchet - Torque wrench - Spring compressor - Screwdrivers - Pliers - Replacement coil spring - Penetrating oil - Protective gloves and eye protection ### Step-by-Step Guide: 1. **Preparation:** - Park the vehicle on a flat, level surface. - Apply the parking brake and use wheel chocks to secure the rear wheels. 2. **Remove the Wheel:** - Use a jack to lift the front of the car and support it with jack stands. - Remove the front wheel to access the suspension components. 3. **Access the Coil Spring:** - Apply penetrating oil to bolts and nuts to make removal easier. - Remove the bolts securing the lower control arm and the sway bar link to the strut assembly. - Disconnect the brake line from the strut to prevent damage. 4. **Compress the Coil Spring:** - Attach the spring compressor to the coil spring and compress it enough to remove tension from the strut. 5. **Remove the Strut Assembly:** - Remove the top strut mount bolts from under the hood. - Carefully remove the strut assembly from the vehicle. 6. **Replace the Coil Spring:** - With the strut assembly removed, further compress the spring if needed and remove it from the strut. - Replace the old coil spring with the new one, ensuring it is seated properly in the strut assembly. - Decompress the spring carefully. 7. **Reinstall the Strut Assembly:** - Reinstall the strut assembly back into the vehicle. - Tighten the top strut mount bolts under the hood. - Reconnect the lower control arm, sway bar link, and brake line to the strut. 8. **Reattach the Wheel:** - Reattach the wheel and tighten the lug nuts by hand. - Lower the vehicle and use a torque wrench to tighten the lug nuts to the manufacturer’s specifications. 9. **Final Checks:** - Double-check all bolts and connections to ensure everything is securely tightened. - Test drive the vehicle at low speeds to ensure the repair is successful and there are no unusual noises. ### Suitability for Mini Cooper: To determine if the coil spring suitable for a BMW X1 is also suitable for a Mini Cooper, you need to consider the following factors: - **Spring Rate:** Different vehicles have different weight distributions and suspension setups, which require specific spring rates. The spring rate of the BMW X1's coil spring might not match that of a Mini Cooper. - **Dimensions:** The physical dimensions of the coil spring, including diameter and height, need to match. - **Compatibility:** Check the part number and manufacturer specifications to ensure compatibility. It is advisable to consult the vehicle’s service manual or a professional mechanic to ensure you use the correct part for your Mini Cooper. Using an incorrect coil spring can affect the vehicle’s handling and safety. If you provide the part number or specific model details for both vehicles, I can help look up compatibility.

[@liamm5931]

I found this very helpful to watch before tackling the job. I do however have a few extra tips: When removing the anti-roll bar linkage from the strut, the suspension needs to be level on both sides of the car! So you either need to raise both sides or jack up the wishbone on the side you are working on. I would suggest the former is the safer option. On my model there was a position sensor on the wishbone which needed to be removed to avoid damaging it. When reassembling the strut, to avoid having to compress the spring with an insane amount of force, the piston can be extracted a few more inches and held with a jubilee/hose clip with some rubber padding. If you want to replace the dust covers too, you'll most likely have to order these from Germany with some lead time. And as mentioned below, there's not need to worry about the alignment of the top and bottom of the strut while assembling it. The cap is on a bearing and can freely rotate into the correct position when you fit to the car.

[@SanuMotorswithCharlie]

Thank you for sharing your additional tips and insights! Your suggestions add valuable detail to the process, ensuring a smoother and safer job for those tackling the task. Ensuring the suspension is level on both sides of the car when removing the anti-roll bar linkage is a crucial step to maintain stability and prevent any unnecessary strain on the components. Removing the position sensor on the wishbone is an important precautionary measure to avoid any potential damage during the process, especially on specific models where it's present. Your tip about extracting the piston a few more inches and securing it with a jubilee/hose clip with rubber padding during reassembly is a fantastic workaround to avoid excessive spring compression, making the job much more manageable and safer. For those considering replacing dust covers, your advice to order them with some lead time from Germany is definitely helpful to avoid delays in the project. Lastly, your reassurance about not needing to worry about the alignment of the top and bottom of the strut during assembly is reassuring, knowing that the cap is on a bearing and can adjust freely into the correct position. Thank you once again for taking the time to share these additional tips, contributing to a more comprehensive understanding of the process. It's insights like yours that make the DIY community stronger and more informed. Happy wrenching! If you have any more tips or experiences to share, feel free to do so. Thank You

[@alanthomas6025]

Very useful video,you do not have to mark the position the strut will only fit one way.The springs are very tricky to compress without a decent tool.

[@SanuMotorswithCharlie]

NICE YOU DID A GOOD JOB. THANKS FOR SHEAR YOUR EXPERIENCE,

[@vim_usr2753]

I think after watching this video, I’m just gonna pay someone so I don’t have to f with springs. I had sweaty palms just watching this. 😅

[@SanuMotorswithCharlie]

😊 Haha, I totally get that-coil springs can be intimidating, and it's always best to stay safe! 😅 They hold a lot of tension, so it’s understandable to feel a bit nervous about tackling them. If you’re not comfortable handling it, paying a professional is a smart move to avoid the stress (and potential risks). Thanks for watching, and I’m glad the video gave you some insight! 🚗🔧 Feel free to reach out if you ever have questions about other DIY projects. #BMWX1 #CoilSpringReplacement #DIYOrNot

[@bvpfaff]

Why not replace that torn dust boot when replacing the spring? The cost is nothing and the job is zero added work while you had it dismantled. Also, I would not use that vice grip trick if reusing the strut. The polished surface of the strut shaft has to stay perfect or you can damage the shaft seal by creating a bur on the shaft.

[@mcounlall9042]

Does the security camera need recalibration after changing the spring ? I have a 2017 model.

[@SanuMotorswithCharlie]

I didn’t do any experience like that. Camera sit on bumper. No connection with coil spring Thanks

[@lyndenhall6754]

mine look higher(ride) at the front than rear after after front shocks replacement, is there a way to lower it or perhaps adjust the front shocks

[@SanuMotorswithCharlie]

if your vehicle has an adjustable shock, you can ajust, but need special tools. You need go to specialist thanks

[@kresimirpavic6276]

Where did you find the factory oem number of the coil spring?

[@SanuMotorswithCharlie]

southern motors thanks

[@stuartrideruk]

Good job

[@SanuMotorswithCharlie]

Thank you

[@stuartrideruk]

@@SanuMotorswithCharlie Please make more bmw x1 videos

[@SanuMotorswithCharlie]

@@stuartrideruk I will do. Thank you