How to Replace Front Wheel Hub 11-14 Chrysler 200

Buy Now!
New Wheel Bearing & Hub Assembly from 1AAuto.com trq.video/ia-1...
New Wheel Bearing & Hub Assembly Set from 1AAuto.com trq.video/ia-1...
This video shows you how to install a new, quality, TRQ wheel hub on your 11-14 Chrysler 200. Head over to TRQAutoparts.com for more info!
• Check here for more videos on the 2011-14 Chrysler 200: • Chrysler 200 2011-2014...
This repair was done on a 2013 Chrysler 200 Touring 2.4L Sedan 4-Door FWD and the process should be similar on the following vehicles:
2011 Chrysler 200
2012 Chrysler 200
2013 Chrysler 200
2014 Chrysler 200
Tools you will need:
• Flat Blade Screwdriver trq.video/oMY-...
• Pry Bar trq.video/okW-...
• 14mm Socket trq.video/oMk-...
• 15mm Socket trq.video/oMk-...
• 18mm Socket
• 19mm Socket
• Brake Caliper Compressor Tool. Single Piston. Lever Style. www.1aauto.com...
• Brake Caliper Hanger trq.video/ob9-...
• 1/2 Inch Impact Gun trq.video/odI-...
• 1-1/4 Inch Socket
• 1/2 Inch Breaker Bar trq.video/oem-...
• Ratchet trq.video/oRc-...
• Torque Wrench trq.video/oyv-...
• Anti-Seize Grease
• Copper Anti-Seize
• Rust Penetrant
• Hammer
• Wire Brush trq.video/oeq-...
Subscribe: / @trq
Check out our playlist:
Chrysler 200 2011-2014 1st Gen: • Chrysler 200 2011-2014...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@rondellschuyler7074]

Good video. Clear explaining. This will help me greatly with my 2012 200s. 196k and doing well

[@ronzigato]

Thanks for calling out the torque specs, super helpful.

[@malikamirshabazz7032]

Thank you for your video this has helped so much🎉!

[@GASSmallEngine]

Good video, small suggestion.. suggest checking master cylinder fluid level before compressing caliper cylinder in. Also you're not moving air, if you had air in the line we'd have a different video. Finally compressing the caliper cylinder all that way when installing same rotor and pads is not necessary, and can damage some abs systems or master cylinders.

[@coastalorphan]

For the caliper pins, I was taught the pin with the rubber bushing is always the trailing pin. Putting it at the top would make it the leading pin as the wheel moves forward. Are you sure it should go at the top?

[@AFPanduhh83]

Was it a bad idea to anti on the bolts for the hub then torque to 35ft-lbs? I'm in Wisconsin and they didn't want to come out very wheel all rusty cleaned off with wire wheel but figured for the next time the next person gonna be thankful.

[@kingmyersgaming5582]

I tried this but I just need to get the stud onto the hub n that’s it but the bolts are giving me hell I’m guessing that u have to remove the hub nut then try taking them off?

[@brettashley5349]

Thanks for the video, saved me a good amount of time!

[@deserteagle2209]

Very clear video to see what’s going on, thanks for sharing, subbed 👍👍

[@defailboys]

What do you call the little washer that sits between the hub and axle i cannot find a replacement and mine were pretty rusty new assembly didn't come with any

[@isky3157]

Can I use an impact gun?

[@heatherpillar5163]

Great video thanks

[@TRQ]

+Heather Pillar Thanks for watching our video! 1aau.to/m/Shop-TRQ

[@davidrobins4025]

What do you recommend as a brake lubricant to prevent the breaks from squealing?

[@davidsias5351]

I never understood why other techs always take the caliper and then the bracket off when you can just take the bracket off and save yourself a step and second why would you compress the caliper after you loosened it

[@perrypayne7100]

Maybe they put new brake pads on but forget to tell us.

[@Not_danny_devito]

I cheated, supported the caliper and bracket instead of taking it off the bracket lol much less time consuming

[@pillpoppa007]

What happens if you don’t torque your bolts ?

[@jasonmcintosh3867]

Two ugga duggas will be ok on this. Three on the axle nut.

[@JjHarrishonda]

I never torque mine lol I just do it. I even have a tq wrenchlol

[@jontewatson6434]

Just tighten as tight as you can with a good wrench you'll be fine I never torgue done either