How to Replace Idler Arm & Mounting Bracket 2000-06 Chevy Tahoe

Buy Now!
New Idler Arm from 1AAuto.com 1aau.to/ic/1ASI...
New Idler Arm Bracket Assembly from 1AAuto.com 1aau.to/ic/1ASI...
If you have to replace the idler arm in your vehicle, odds are, you’ll need to replace the bracket too. Best to get them both done at the same time! This video shows you how to install a new idler arm bracket in your 2000-2006 Chevy Tahoe.
• Check here for more videos on the 2000-06 Chevy Tahoe • Chevy Tahoe 2000-06 2n...
This process should be similar on the following vehicles:
2000 Chevrolet Tahoe
2001 Chevrolet Tahoe
2002 Chevrolet Tahoe
2003 Chevrolet Tahoe
2004 Chevrolet Tahoe
2005 Chevrolet Tahoe
2006 Chevrolet Tahoe
Tools you will need:
• 21mm wrench
• 15mm Socket 1aau.to/oa/1AXA...
• 21mm Socket 1aau.to/oa/1AXA...
• 22mm Socket 1aau.to/oa/1AXA...
• 24mm Socket
• Ball Joint Press
• Pickle Fork
• Side Cutters
• 1/2 Inch Air Impact Gun 1aau.to/oa/1AXA...
• Torque Wrench 1aau.to/oa/1AXA...
• Drill
• Cotter Pin
• Hammer 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Chevy Tahoe 2000-06 2nd Generation: • Chevy Tahoe 2000-06 2n...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

[@altruistic232]

Is there a torque spec. on the nut joining the idler mount to the arm ?

[@agelesspuma]

Do you need to take vehicle for an alignment after changing the parts?

[@taylorstevens48]

That thing was on there, just did mine on a 274k original parts, hit it with just the are hammer and popes right off

[@TheBrickhoused]

What is that puller that you tried to use called? I am trying to find one of those and am not having luck

[@angelbenavides5784]

Any torque spec on the nut that goes from the idler arm to the bracket???? I'm assuming the same torque as the castle nut ???

[@ftorres8797]

Took me weeks to find the tool everyone is asking, J-43631 kent moore, cheaper version is the OTC 6655

[@thechosen5805]

Great work

[@ftorres8797]

What is the name of the tool you used first that didn't work?

[@Cartduckmann]

my bolt from my idler arm mount just spins and doesn’t allow me to tighten it down all the way, any idea what’s going on both brand new parts from trq

[@kirara9182]

What about grease fittings?

[@FinsleysCustomCarAudio]

Do you have to change braket?

[@mrnobody292]

How did you slide the bracket in so easy

[@looseparashoot]

2wd

[@JohnDoe-mh8tm]

Why did you skip the torque on the idler arm to bracket torque?!

[@Eparker09]

Thanks

[@red7fifty]

GREASE it, otherwise you'll be doing this again sooner rather than later.

[@TRQ]

+red7fifty Thanks for the feedback! 1aau.to/m/Shop-TRQ

[@altruistic232]

Is there a torque spec. on the nut joining the idler mount to the arm ?

[@SkinnySkinch]

good'n'tight