Thanks a lot for you and all the other youtubers. I managed to watch these videos and fix my TV for just 1/10th of the repair cost.
@GoingShirtless Жыл бұрын
I have seen two of these repairs now and it surprises me that you can just knotch like that into the diffuser with nothing more than a utility knife. I would have been tempted to grind and polish with a dremel-like tool or even cut a whole length of strip from the edge to keep it uniformly wide and give the light the same travel distance. I tend to overthink these things :D
@zauberhaft1 Жыл бұрын
Thank You, Just what I'm looking for, how to remove the back panel, I saw that I have to remove the metal wires, just as you showed in this video! I was realy strugling, but now I know! Very impressive, and the only video that showed this on You Tube! Maybe tomorrow I will have opened the backpanel too!
@Smallwood-pw1mm Жыл бұрын
Thanks for sharing. Never thought a single strip of led providing all the backlighting.
@eddiexx Жыл бұрын
Nice work guys! Just two question. 1-Why did you need to pull those long metal sticks before removing the cover and when putting the cover back they didn't seem to matter? 2- Does the Q70R have those metal sticks? Regards/Ed
@martin_s28 Жыл бұрын
The back cover seems to latch on the wire when you put it back on and for disassembly you need to pull them out or the tabs might break off
@ВладимирГрунин-й4и Жыл бұрын
A huge like for disassembling and restoring the reflector, good luck in our hard work and most importantly health
@EasyLearningWithShahid2 ай бұрын
Hi there! I got only a white flash rest of black screen. How to fix that?
@sirano30 Жыл бұрын
Hello, I have replaced both LED strips. After reassembly I have the same problem in the same place. Can it also be due to something else?
@Viggen662 жыл бұрын
Where did u get those suction cups?
@jmservis23706 ай бұрын
Thank you for sharing your experience, very useful
@epeixel12 жыл бұрын
Olá, Baixou a tensão dos leds para não voltarem a queimar? Se sim, como fez? Obrigado desde já.
@NelsinhoPira Жыл бұрын
Aqui substituo o resistor de limitação de corrente que fica no Dreno do fet de controle de corrente na placa da fonte. É de baixo valor, geralmente de menos de 1 ohm, suba o valor em aproximadamente 50% maior.
@mrkonstantinos2011 Жыл бұрын
Good job 👍
@chancetolbert48522 жыл бұрын
Lol found this AFTER i broke some of the plastic. BIG question. The ribbon cables attached to the first panel you removed with suction cups. I had 1 that came loose from circuit board. How do you reattach. Second. There is a slight damaged piece in the middle of one of those ribbons. Appeared to have been there.... how can i find replacement ribbons for this? I cannot find a part number on it. Most importantly though how do you reattach to the circuit board
@NelsinhoPira Жыл бұрын
Sou do Brasil e gostaria de visitar seu país. Quando for viajar, tentarei ir aí conhecê-lo. Diga se há trabalho aí em seu país para estrangeiros com experiência neste tipo de trabalho, pois faço isso há muito tempo.
@jnobull45 Жыл бұрын
Where can I buy the scream from online that was showing at 3:25 that you had to use the suction clamps on to remove?
@randykaufman876 Жыл бұрын
Great video! Question, I am working to replace the LEDs on a UN85AU8000F (85") and have gotten down to the LED Strips. They are clearly fried and need to be replaced; however, the connectors on the wire harness connecting the 4 strips to the board are not in good shape. I have been all over the internet to find replacements with no success. Do you have any advice on how to replace them? The LED Part number is LM41-01047A/C. Thanks!
@lukep471410 ай бұрын
Any update?
@jongalpuerto57118 ай бұрын
Thanks for tutorial...How and where to purchase the sanction cups and the LED strips?
@CRAZYHEART373 Жыл бұрын
Where you bought the back light strip please
@johnvanduyvenbode10 ай бұрын
A very educational video. Thank You!
@dimitra.d7922 жыл бұрын
hi sir very nice video because in my case i have similar with above model 50 inches and the haif screen is black and the other illuminate almost complete is there a way to test the led strips from the plug of tv board ? the plug has 8 pairs of wire do you know about ?
@NelsinhoPira Жыл бұрын
8 pares de fios pois são divididos em 8 séries de leds.
@canaldopedro8759 Жыл бұрын
Hi, goog job! Which model is the TV of your video?
@ronaldnivar745110 ай бұрын
I replaced the LED strips and the tv still does not work.
@songribjyotikalita33826 күн бұрын
KZbin dekhke kaam karne se aisahi hota hain..
@borcanul28 Жыл бұрын
Mersi, am salvat 2 modele 2020 , de la niste germani care le-au aruncat la gunoi pe motiv ca are umbre pe ecran, adica led uri arse :)) sunt de 55 inch 4k
@sjp68996 ай бұрын
Hi, Great video. I change my LED the same way and it worked. But after few hours of screen time few LED died off. What could be the reason?? I bought my LED from AliExpress. I also noticed that when I changed my LED the previous once were burned and it burned the white panel a little bit too. I am guessing my TV might have something else faulty like on board which controls power to LED. Please let me know if you have some clue???
@EnTeknolojiАй бұрын
Yanan Reflektörü (LGP) yenisiyle değiştirmen gerekiyordu alt kısımda ışık hüzmesi yapacak ve kısa sürere çatlayacaktır.
@DonatasJankauskas-ez3ky5 ай бұрын
what is the price of the led screen and where did you buy it, would it be possible to get a link?
@wilianenriquemartinezramos54469 ай бұрын
Excelente demostración gracias
@rcary Жыл бұрын
Question . My edge light led melted a little bit of the thick diffuser panel which sits close to them. After replacing the strips I noticed a bit of light scatter around the bottom edge. I think it's because the led had made a little melt mark on the edge of the panel. Would it be OK to sand that edge with a fine sandpaper to bring a smooth finish back again? The panel is not the easiest thing to find anywhere used online. Any advice welcomed. 👍
@NelsinhoPira Жыл бұрын
Aqui no Brasil trocamos o painel acrílico difusor de luz quando este apresenta derretimento por calor. Custa caro mas o resultado fica perfeito. Quando não é trocado o difusor de luz, ficam manchas. Here in Brazil, we change the light diffusing acrylic panel when it melts due to heat. It is expensive but the result is perfect. When the light diffuser is not changed, stains remain.
@rcary Жыл бұрын
@@NelsinhoPira sorry, can you translate. 👍
@TheAntirossi5 ай бұрын
Bro you’re awesome ❤❤❤❤👏🏻👏🏻👏🏻👏🏻
@TheGoldi13697 ай бұрын
Hey, thanks for tutorial, I have chaned my LED panels and they start lighting up with different coors two yellow and two white blueish, and from one of them smokes comes up, so unplugued it fast and do not know what might be the reason. any idea could be the power board is faulty
@Kennethcrown37208 ай бұрын
dont you need to discharge the conductors or is it only on UE497105K?
@Waynechuks Жыл бұрын
I need to do this. I am worried i might break something. This is good videa for what i need to do. Samsung UE50NU7020 backlight.
@moulonz Жыл бұрын
This video would of been so much better if you didn’t put this stupid music in the background and just explained what you was doing step by step.
@uniteddeejys12692 жыл бұрын
Guys! Honestly, far more one of the best tutorial .. BUT .. please explain, why do you have to cut out part methods from the video, one second the white plastic rectangle "ring" is out the next second is already on .. it is missing key parts .. and the whole story is become unuseful.. it would be 30sec extra to show those moments.. please explain why you have to remove those
@juanantonio8561 Жыл бұрын
I recommend you put on some latex gloves to handle the plastic sheets that are inside since you leave grease from your hands on them and then stains appear.
@elijahnanaoseiameyaw98192 жыл бұрын
Any videos on how to change backlight for Q90/95 series?
@jaylarida49322 жыл бұрын
what kind specifically is that led strip you replaced?
@Nilmoy2 ай бұрын
I bought the LED strips on Aliexpress, search was quick.
@morrisrossi85702 ай бұрын
Great video tks from Italy !!!
@mrinfelix45749 ай бұрын
6:22 seconds in when you switch it on, mine isn't doing that with the old SMD's I wanted to see which ones were faulty, so all I can do I guess is fit the new ones and put it back together and then hope for the best I guess. (Of course just all the components connected etc.)
@ssbbdtv Жыл бұрын
very nice repair
@nwrlynwralmstfyalmstfyn8980 Жыл бұрын
nice work 👏
@kolamiris2 ай бұрын
Where to buy the replacement panel from? I need to replace it for a 32" Samsung Curved monitor LU32R591CWNXZA FB02
@dawidmarciniak9128 Жыл бұрын
Wymieniłem ledy na nowe tv chodził pół dnia,włączam na drugi dzień znowu czarny ekran?
@AlokElectronicsVinaySinghАй бұрын
How to buy a panel removers vacuum clip please send a link in Amazon and Flipkart
@witherscreations5 ай бұрын
can u flip the burnt plastic diffuser screen 180 degrees
@muthukumaravel9913 Жыл бұрын
Very nice sir Good job thanks sir
@dudebro20013 жыл бұрын
Those 2 little strip boards connected at the bottom of the panel held together by ribbons..... What are those called
@chancetolbert48522 жыл бұрын
Ever figure this out? I need to replace one too
@n55m6a7 Жыл бұрын
👍👍 Cam târziu, dar v-am descoperit.... Multa bafta....
@SuperMana073 жыл бұрын
Pt 43nu7122 backlight issue. Interesat de inlocuire leduri si dispersor lumina (se pare ca nu se gaseste). Ar putea fi reparat?
@rccrazybill Жыл бұрын
I’ve got a 3 year old Samsung 65” tv that the backlighting burnt out . I replaced the light strips but the white plastic that sits against the chassis melted slightly and cracked from when the lights burnt out . The picture is beautiful but you can see light at the very bottom and the cracks appear through the glass . Is there anyway to fix this ? Can I purchase this item ? I don’t even know what it’s called . It’s a shame to get rid of the tv . Any help will be greatly appreciated
@NelsinhoPira Жыл бұрын
Aqui no Brasil há o painel de acrílico difusor de luz para trocar, é bem caro mas você pode procurar por algum aparelho usado que quebrou a tela para comprar e reaproveitar esta peça.
@pomemega10 ай бұрын
Warning-I recently changed my led backlights and now can see display but unfortunately the suction cups left rings on display is it permanently damaged?
@mohdisyrafqayyummohdrazip74128 ай бұрын
Hi, if only one side is burnt, should I replace both LED or only the damaged ?
@MrPetik1477 ай бұрын
If you want do same job in next half year replace only one 😂 oh my god that question
@soran2020 Жыл бұрын
Hello sir where and how i can get Led size 49 for my samsung tv.
@Defcon666 Жыл бұрын
WHAT ?
@matkrzysiek51089 ай бұрын
Super!
@amitagarwal3476 Жыл бұрын
Sir can you please tell me the backlight price
@j0s4y08 Жыл бұрын
What model is this tv
@Shabirshah2010 Жыл бұрын
How to replace polarizer flim on Samsung 4k 55 led tv
@MdBabu-kb7xb Жыл бұрын
Vai amar akta Samsung tv lcd nosto hoye gace lcd change korte kamon khoroc lagbe
@yuvrajkinkar2702 Жыл бұрын
Very nice
@Georgatzis11 ай бұрын
thanks, hept me a lot
@RaviKumar-du5qr Жыл бұрын
So nice work 👌👌👌👌
@PatentIllustrator Жыл бұрын
Where can one purchase the black glass panel screen only?
@NelsinhoPira Жыл бұрын
Isto é o painel lcd. É muito caro e não compensa a troca. Compre um novo televisor.
@jeanturcotte2098 Жыл бұрын
Bien Fait en PROFESSIONNEL A+
@danielababei8033 жыл бұрын
Un samsung ue55ku6400,cu o problema -linie mai luminoasa in partea de jos a ecranului...ar fi putea fi una din barele LED? Cum as putea trimite foto (email)pentru explicatie?Multumesc
@ludiscnet8514Ай бұрын
Thankyou
@albertchiu655 Жыл бұрын
professional !
@AlexeyZhukovin3 ай бұрын
Thanks!
@mohammedkharbouch2862 Жыл бұрын
I removed the black spots from the white (RGB) plastic. Will the LED lights last for a long time? Better to replace the LEDs and the white RGB plastic
@NJlearninggroup115 Жыл бұрын
Cost?
@cooperwheeler525711 ай бұрын
THANK YOU
@davelombs5181 Жыл бұрын
Absolutely weird you need to fix after 4 years this smart tv, this is what happen to me, i will never buy a samsung tv again!
@muitza862 жыл бұрын
Salut! Ma poti ajuta cu o informatie? Am un LG40UH630V caruia ii clipeste ledul rosu de 3 ori cand il aprind dar nu afiseaza nimic pe display, e negru complet, iar pe placa sursei de alimentare in partea de secundar clipeste un led de 5 ori si repede. La bornele de testare tensiune leduri am 17 V in loc de 13,2. Daca ati mai intalnit acest tip de defect! Va multumesc anticipat!
@thanhphamvan9899Ай бұрын
I want to buy an lcd lifting tool
@Bionicbabyy5 ай бұрын
Nice video, but it does not show how to take the clips off.
@AyanMondal-o7g Жыл бұрын
great job
@stffwtf2 жыл бұрын
Bei mir sind die LED's auch verbrannt. Eine Folie angerannt, muss mal schauen ob man die weglassen kann.
@alanquarterthane4825 Жыл бұрын
You are my teacher
@ssc-maths-4 ай бұрын
Super
@emilbenedict73767 ай бұрын
salut cum pot lua legatura cu voi! un nr de telefon va rog!
@pascalaufloringheorghe20799 ай бұрын
Am un qe55q6fnat si Nu mai se apri de ecranu la el ce sa fac
@AK-ig3ko Жыл бұрын
no need words👏👏👏👏👏👏👏👏👏👏
@mariusalinmarginean60663 жыл бұрын
Bravoo!!!!
@VadimGiacint9 ай бұрын
Зачем рвать старую подсветку. Подогрей феном.
@fish126910 ай бұрын
Not what I'd call a tutorial...
@marceloaugustodesallesgomes8 ай бұрын
MAERCET.LO UGU LLES 🖨⌨️🖥🤓🤓 as coisas às ae o ase e a sua casa é uma as axc o meu nome
@sandipbhagat42882 жыл бұрын
Suparb 👌👌👌👋👋👋👋👍👍
@tommajor1013 Жыл бұрын
when the dust enters in the backlight layers there is no way to get it out,all those efforts are in vain-its working but will look ugly
@JK11saleemawan.1432 жыл бұрын
Hi sir where are you from
@electronic.service2 жыл бұрын
Hello, I'm from romania.
@harpreetsingh9213 Жыл бұрын
@@electronic.service Hello very work, is 4k 55" TV's panel available in Romania? We are living in Poland, I am waiting for your answer, Thank you,
@gicugigel3790 Жыл бұрын
@@electronic.service salut. Ce sunt acele cartonase pe care le pui pe sub marginile display-ului?
@DrarslanAbdulsattar Жыл бұрын
thankyou to master of teacher to skil giving giver to crepers
@AdamHR119 ай бұрын
In Western Europe, this kind of repair would cost as much as a new TV, if not more.
@indiancreativemind5042 Жыл бұрын
Only one strip others led tv have full of back light led
@pascalaufloringheorghe20799 ай бұрын
Pornea si se stingea singur am pus banda pe 2 circuite acum Nu mai face asa da Nu am Imagine Am sunet dar Nu imagine ce e de facut
@ratebothman4084 Жыл бұрын
Good job
@phaenius Жыл бұрын
Nu ar trebui pus ceva moale sub ecran cand sta pe masa, sa nu se zgarie?
@gssingh4477 Жыл бұрын
Good
@123pradeepkuma11 ай бұрын
Hi sir
@faheemfaheemfaheemabdullah Жыл бұрын
good
@شهرام-ص1ط Жыл бұрын
Perfect
@thetruth7839 Жыл бұрын
So when you're putting the black screen back on and you have that little metal with all those green Flaps attached to it that is connected to the bottom of the screen I accidentally ripped one of those off from the metal how do I renew it back on
@goodfodder Жыл бұрын
yep problem with my tv, last time I buy Samsung
@thetruth7839 Жыл бұрын
So that dangly part that is attached to the front screen I accidentally pulled one of the tabs off how do I reattach it is it just glued on or is it soldered in😊. I put my TV back together and I have one black line about 5 in wide from top to bottom. I open my TV up and it's loose somehow I pulled it off it's one of the ones in the middle how do I reattach that please tell me
@gatosgataros22188 ай бұрын
3:52 there is no cooling for those poor leds to help them live longer...those poor little leds ... omg ... and they aren't a lot .... 450 nits of luminance ... all that in a tinny ledstrip ...