worked perfect on my 2014 camry. thanks for making the video and offering the part for sale at a reasonable price!
@herrenmann5 жыл бұрын
thank you for the compliments!
@shilohkamari18123 жыл бұрын
InstaBlaster
@juanmazazueta4382 жыл бұрын
@@herrenmann me too.tanks so much. From tijuana mexico
@TomBombadil336 ай бұрын
Some notes from my experience: - Make sure when installing the digitizer, that the pins on the ribbon are facing DOWN towards the circuit board. The digitizer I received had a ribbon with bends in it similar to the existing one, but the bends were oriented in the opposite direction, causing me to install the digitizer backwards initially. - Be careful not to get fingerprints on the inside of the digitzer screen, or to wipe them off before installing! Installation went smoothly other than the above issues. Thank you for the great video!
@petewolfe95226 ай бұрын
I almost did the same for the exact same reasons! Also make sure you keep the little rubber piece that acts like a spacer from the touch pad to the screen.
@mateol9167 ай бұрын
I just used your video to fix my stereo. Worked perfect!! Thank you for the upload and sharing. Saved me some money brotha.
@xjanosikx7 ай бұрын
thanks just saved $300!
@otownavi3 жыл бұрын
Few notes from my successful repair using this video. 1. 10MM socket for the bolts 2. Need to push the metal tabs in to separate screen from main box. Then push them out again once you have completed the replacement and are ready to reassemble. 3. Not all the ribbon locks/braces open the same way. Some swing up and some slide out. If pulling up isn't working then slide. 4. Always good idea to take photos of how it looked before disassembly. Overall it is a quick and easy fix. Worked like a charm. Thank you for the video and parts. Cheers
@fleem5 Жыл бұрын
Ordered the $18 replacement screen from Amazon. It came in and I tried this. Yes! Success! Took me about 30 minutes to get it done. Thank you very much for uploading this vid.
@soxpatsbruinscelts78003 жыл бұрын
Performed the swap today on my 2015 Corolla S. You need a 10mm socket wrench to remove the bolts. Most difficult part was loosening the tabs all around the unit to remove the face. The four small screws around the display circuit board are very tight and I stripped them somewhat getting them out and back in. Otherwise this was very simple and took less than 45 minutes. I was surprised by how easy the dashboard snapped back on... I contemplated this fix for over a year and now I wish I did it sooner. Thank you so much for making this available!
@JonLane-l7n28 күн бұрын
Great video. I replaced the digitizer today. The key things are: 10mm for the 4 bolts, you don't need to take the side brackets off, but it is easier, careful with the clips that hold the cables to the circuit board, the little doors swing open, then the ribbon comes out. Reverse slide the ribbon in, and then the little door closes snug and holds the ribbon in. Make sure you have a micro screw driver set, the screws damage easily. Take your time and take pictures of how it's set up, etc. So you can put it back together. BTW, Toyota quoted me $1000 to repair or $3000 to replace the unit. The trickiest part for me was the little ribbon doors. They break easily. I had to repair one, wasn't easy.
@michaelcarrera9236 Жыл бұрын
I did the screen swap today. Took me 1 hr just because I didn't have the right screwdriver size and when reinstalling everything, I didn't tighten the 4x screws for the screen tight enough so I had to remove from call and redo. Very happy now that the touch screen is functioning
@stevemoser96364 жыл бұрын
Excellent video. I just replaced the digitizer on my 2014 Camry using your video as a guide. I had the same dead zone on the screen bottom. It started out on the left and finally nothing on the bottom row worked. Fixed good as new. Thanks again.
@johnnysriin3853 Жыл бұрын
worked perfect on my 2015 Corolla LE. thanks for making the video and offering the part for sale at a reasonable price! 10
@eckergus3 жыл бұрын
I just fixed mine on my 2015 Corolla and it now works flawlessly! Thanks to YOU! Thank you SO much for taking the time to share this information!
@averimorley6877 Жыл бұрын
Did this today, got the part off of Amazon $25. When I first put it back in it didn’t turn on at all. Took it back apart, stripped one of the screws, but I didn’t put one ribbon back in correctly. Put it back in and worked perfectly! No more dead bottom half!
@EricBRowell6 ай бұрын
Your breakdown was more than enough for me to do it myself. $20 on Amazon for the part and 30 minutes to do it. Size 0 and 00 screwdrivers helped avoid stripped screws.
@garywinkel18313 жыл бұрын
EXCELLENT VIDEO! I found the replacement screen on Amazon for $18. Just replaced this on my daughter's Corolla tonight and it's once again working like new! Thank you!
@gavin9056 Жыл бұрын
I just got a new phone and needed to hit the “add” button to Bluetooth, bottom left side and couldn’t(hasn’t worked since like year 2). I called Toyota and they said it would be $4,000 to fix. I LOLED. I am so glad I found this video last night. Ordering the part today. Really hope this works or else I’m getting a new car lol
@zflood992 жыл бұрын
This worked on my 2016 Corolla S and only took about 45 minutes! I and my bank account thank you sir!
@dlbtrung2 жыл бұрын
Did your volume button work when you had an issue with touch screen? I am driving 2016 Corolla S and having the similar issue. The up/down buttons on steering wheel are also not working. Just wonder if I replace the touch screen and all issues are gone.
@zflood992 жыл бұрын
@@dlbtrung my volume buttons we’re working the whole time. I only had the issue with the touch
@Costa200713132 жыл бұрын
This works, I can’t believe it. It save me a lot of money.
@darrenthomas9810 Жыл бұрын
Great video solved all my problems with a $25 screen from amazon. One tip is your gonna need the smaller screwdriver set to get the screws when you get to the actual radio itself. starting with the 3 in the bottom. the screen clips can be annoying but they will come off. THANKS FOR THIS VIDEO SAVED ME SOO MUCH $$$$ I DONT HAVE.
@petewolfe95226 ай бұрын
Here in 2024. Product link no longer works, but I bought the part a few months back. 100% Successful install! Thank you and make sure you read the other comments for some pro tips
@robertocervantesramos2584Ай бұрын
Please, where bougth the part. Name part.
@akuma4uАй бұрын
Pls share the new link for part
@cecyorozco3398 Жыл бұрын
THANK YOU SO SO MUCH … followed your video and you saved me a couple 100’s
@stevezhao18273 жыл бұрын
Thank you. one of our local Toyota service gave me an quote of 1200$. They planing to replace the whole radio system..... Now I just need spend 20$ on Amazon and few hours of my spared time.
@jamesturnure97355 жыл бұрын
OK, so the digitizer arrived yesterday and I decided to install it last night. Your video allowed me to complete the job in about 40 minutes, thank you! So, one piece of advice to anyone attempting this repair....two of the ribbon cables have notches on either edge that must fit up and over the pin pad before the latching bail is closed. My head unit didn't work the first time I plugged it in and found the cause to be one ribbon cable not seated. Apart from that, extremely easy. If I had to do one again, it would take 15 minutes. BTW, the screen that I received off your link was excellent.
@herrenmann5 жыл бұрын
im glad it worked for you! thank you for the comment and business!
@KenNYC2123 жыл бұрын
This is a great video, thank you very much - helped me repair my touchscreen! However, you skipped over a couple of the most difficult/confusing parts - putting it back together! Some things to watch out for when re-installing the screen: The screen I ordered had glue on one side, and the black piece that goes around the edges doesn't exactly align. Also, after removing it from the original screen (which did not seem to have glue, for some reason) the black foam piece separated right away before I could note the exact way it was attached, and it was hard to remember which way the black piece went back on, as the 12-pin cable is not exactly in the center and for some reason the black thing has protrusions that overlap the edge of the screen. So I wasn't exactly sure how to line it up or which side of the screen was supposed to face front (the first time, I installed it backwards based on the way the cable was naturally bent, which for some reason was bent in the opposite direction of the original screen). Luckily I realized before re-assembling the whole thing, based on the fact that the 12-pin ribbon cable is just slightly off center (a little to the left) so by putting the wrong side forward, the ribbon cable was slightly askew to the place where it plugged in on the circuit board. I then had to pop out the screen from the plastic frame and reverse it, then the cable lined up better, so I assumed that was the side that should face "out". But I did spend an extra 20 minutes or removing/reversing it based on the pin layouts and cable placements, carefully studying the screen and cable up close, trying to determine which was the right way to insert it into the plastic frame. I also ended up getting the black foam a little crooked, and once it was affixed it couldn't be removed to be straightened (I would have had to buy another screen), but it worked anyway and didn't appear to be visible once installed. I don't know what that black foam piece does, but I assume it's important.... Would be helpful to see the right way to exactly line it up and affix it to the screen...and know what all the little cutouts are supposed to line up with. Lastly, watch out as the screen scratches very easily - just holding up the old screen to compare, somehow I managed to put a small scratch in it with the corner of the other screen. Seems very sensitive to scratches so be extra careful!
@ArsonistArborist Жыл бұрын
Thanks for all the tips! Can’t wait til mine comes in
@ArsonistArborist Жыл бұрын
@Ken Shvetz thank you for your advice! I installed the screen, started putting it back together and the ribbon that actually hooks up the touch screen didn't want to go in all the way.. then I noticed it wasn't perfectly lined up and I thought I had read something about that in the comments. Came back, read your comment, pulled the screen, flipped it, and reinstalled it. Probably wasted like 10 minutes, instead of 40 lol. Thank you!
@KenNYC212 Жыл бұрын
@@ArsonistArborist NP, glad I could help! 🤓
@ArsonistArborist Жыл бұрын
@@KenNYC212 you da man 👊🏾
@mtrout6153 жыл бұрын
I have been searching for a fix for this for nearly 2 years and everything I saw said replace the entire screen. I'm ordering the digitizer now and will update if this fix works!!
@herrenmann3 жыл бұрын
Best of luck! The ribbon connectors are flimsy. Just be careful when disconnecting and reconnecting them.
@mtrout6153 жыл бұрын
@@herrenmann I will be VERY careful with the ribbons! Currently waiting for my new digitizer to arrive!
@EnjoyTravelUSA4 жыл бұрын
Man that's great tutorial. Do more video, you explaining really cool
@RoseConeMari2 жыл бұрын
Thank you so much for doing this step by step. I will be doing this tomorrow!!!
@rayortega12432 жыл бұрын
What an awesome video. I will be buying a new touch screen to fix mine. Thank you for the detailed description!!
@svierregger3 жыл бұрын
@JervisTan - Thanks for posting this video. I just fixed the touch screen in my daughter's 2015 Corolla S following your instructions. The only thing I might add is to double check all the ribbon connections while you are reassembling the radio, just to make sure the ribbons are seated securely. Check everything twice, install once. Or something like that. Anyway, you have done the Toyota community a great service by posting this detailed video. Cheers
@greenzrx10 ай бұрын
Thanks for the how-to. Worked perfectly for my daughters Corolla. 👍👍👍
@ProfessorFate2 жыл бұрын
Great video. On my 2014 Corolla LE equipped with gps navigation and XM radio, things were a bit different. On it, there is a module (xm/gps module?) mounted to the bottom of the radio that has three short jumper cables from itself to the main radio body. If you remove it, you will discover the access cover for the front panel connection does not exist. So, don’t bother removing it and read on. You can leave the jumper cables in place as well. This radio’s marked with Toyota PN 86100-02100. To remove the front panel assembly, find 4 small phillips screws in a row along the panel bottom. Remove them. At that point, the front panel assembly is held on by just the black plastic latches. Starting at one end, lift them up while pushing the panel forward until you release the panel. As you free the panel you will find a short flat cable that connects from the panel assembly to a connector in the main radio chassis. Flip up the latch on the main radio connector to free the cable. Now, the front panel repair is same as in the video. My panel off eBay seller tom_autoparts is working perfectly.
@ldrivadrivah8049 Жыл бұрын
Don’t like doing work on small electronics but it saves me hundreds. Will be doing it maybe this weekend
@tailpipe05Күн бұрын
Good info ! This explains the process clearly. Thank you !
@MrBigboy3504 жыл бұрын
Thanks for the video bud. Just did my wife’s 2015 Corolla. Went perfectly.
@ashleyscott96803 жыл бұрын
My thoughts about this before this video was "it can't be any harder than a ds screen" and this basically confirms that!
@troublemaker32 жыл бұрын
I followed the video, except my radio has the satellite radio module mounted under it. It turns out that I don’t have a small access port on the bottom of my radio. So I popped the front off and just manipulated the radio with the main cable still attached. $17 for the digitizer and now my radio works like when it was new. Thanks.
@Kaleb55034 жыл бұрын
thank you so much. works great on my camry 2014. in other instructions for some reason they glue a new glass🤷♂️ thank you from Ukraine)))
@jcco3na3005 жыл бұрын
Thank you very much. Your video helps me a lot, even it wasn't the same radio model I can be able to successfully change the screen. It works perfectly now.
@herrenmann5 жыл бұрын
Julio Cotrina thank you!
@4s-ter4 жыл бұрын
I just completed the repair with your part and instructions and it worked like a charm. Thanks so much!
@sarahfreehauf35443 жыл бұрын
Awesome tutorial, super easy fix. Saved me hundreds. Be careful releasing ribbons, they don't pull out, you need to release them.
@ezazpatel11232 жыл бұрын
Extremely useful and super clear instructions. Thank you!
@willneville2 жыл бұрын
Nice video! I’m going to try this on a used car I just bought. Glad there is an easy fix
@JorgeRodriguez-zo7em2 жыл бұрын
This was very helpfull, i just change the digitizer on my toyota corolla 2015 and this video help me a lot
@jenjarrya50863 жыл бұрын
The bottom left screen just went on my 2014 Corolla... and I watched your video..... you make it look easy... but I too scared to ruin it. Where can I get the part, and do you think most garages (NON Toyota) could replace it?
@ricksclips3 жыл бұрын
you just saved me $100-$200 thank you sooooo much!!!
@dietmoxie552 жыл бұрын
worked perfectly on my 2015 corolla s
@strauss7773 жыл бұрын
Great video man, saved my mother quite a few bucks
@traciswanson46352 жыл бұрын
Thank you having the same problem with my 2014 Camry
@shuyalu605 жыл бұрын
Hey, thanks for the screen! I fixed my screen and saved 1k from the dealership. Thanks for the reminder about the ribbons. I’m not very handy but managed to fix it within 2 hours :)
@herrenmann5 жыл бұрын
thank you very much!
@brycefujimoto80234 жыл бұрын
What about tape around the edges of the touch screen to hold it in place? I wasn’t looking forward to spending a lot of money on a new head unit
@nidanaqvi25644 жыл бұрын
Heyy I was wondering where you bought the part from? The actual Radiohead?
@brycefujimoto80234 жыл бұрын
Nida Naqvi I bought my screen part for the head unit off of eBay for $22.00. Type Touch Screen Glass Digitizer Corolla Camry RAV4 on eBay search. The model of the head unit is a Fujitsu Ten.
@shuyalu604 жыл бұрын
@@brycefujimoto8023 I just followed every step he mentioned in the video. I did not remember I need to tape anything.
@larrystudnitzer3592 жыл бұрын
Thanks worked perfectly on my 2014 toyota corolla
@rahuldesai11223 жыл бұрын
Awesome Jervis! Fixed my screen issue for 20 bucks.
@laurenniedringhaus84103 жыл бұрын
Great Video ! worked on our 2015 Corolla perfectly !
@jessearthur61804 жыл бұрын
Amazing! Worked on my 2015 Corolla le. Matched screen with car on eBay.
@ghostdog20415 жыл бұрын
God bless you for jump cutting past the bolt removal. Liked!
@yhn86102 жыл бұрын
This video is awesome. I have same problem. Thanks for your video. I am going to try
@KasFarhat6 ай бұрын
Great video Does anyone has a link to purchase a touch screen
@Zanbor592 жыл бұрын
thanks for making the video
@mitchelb.77793 жыл бұрын
Big shout out to this guy 👏 thanks for the help!!!
@kevinsantoyo3233 жыл бұрын
Awesome video 💪🏽👍 Fixed my screen for 20$. Thanks man !
@brianlynch92373 ай бұрын
Super helpful. Thank you. Thank you. Thank you.
@wilbervalente253 жыл бұрын
Thanks man for your video,it was very helpful it helped me on my corolla 2015..
@Mojo-cg3xo4 жыл бұрын
good step by step instructions.... however, if my 2014 Corolla touchscreen is constantly rebooting would a screen replacement fix it? If not what is the fix for the constant rebooting of my touchscreen radio?
@herrenmann4 жыл бұрын
i have not come across this constant rebooting problem before so i really cant say if replacing the touchscreen would help. a constant rebooting could mean a hardware failure or a corrupted software that is hindering the radio to startup. i would suggest to start the troubleshooting with software and then move to hardware.
@Mojo-cg3xo4 жыл бұрын
Jervis Tan ..... I took apart the touchscreen radio today this morning looking for any evidence of a burnt transistor, IC chip or capacitor. Measured the each capacity with my ESR meter and everything checked out ok. I believe you maybe correct in the “corrupt software” issue creating the reboot issue. There is a slot for a Micro Sd card, which is the map card that also maybe causing the reboot issue. Some people with the reboot issue have ordered a newly updated Micro Sd map card from EBay or Amazon and they claim this fixed the reboot issue.
@BBALFONSECAPONE2 жыл бұрын
Bless! Saving everyone money from this crappy radio screen!
@alannguyen91324 жыл бұрын
I just change a new screen work great. Thanks
@imyibra26362 жыл бұрын
Fantastic job and video Can you please post a video on how to solve the Bluetooth problem. I cant hair the incoming calls nor can they hear me. That would be fantastic 😀. Thanks for the clear instructions
@herrenmann2 жыл бұрын
Thank you for the comment. Unfortunately I’m not familiar with the Bluetooth problem. If I come across any video related to it. I’ll share it here.
@imyibra26362 жыл бұрын
Thank you for time
@jenjarrya50863 жыл бұрын
Ordered my screen today! HOpefully I can repair it myself!! (Scared)
@herrenmann3 жыл бұрын
dont worry. its not hard to fix.
@ricksclips3 жыл бұрын
it was easy just be easy with the ribbons
@sniperjc223 жыл бұрын
Great video. Saved me tons of money.
@williamkrause56243 жыл бұрын
Well its more than a year later, is the screen you replaced working ok still? I would love to replace mine but i dont want to spend money only to have the new screen go bad. Thank you for the video as it will be very helpful to those of us needing to fix the problem.
@herrenmann3 жыл бұрын
Mine is still good so far. :)
@jeneebell8494 жыл бұрын
worked perfect saved me so much money!!! thanks a bunch!
@douglas9752ify5 жыл бұрын
This has been very helpful, thank you so much for the tutorial!
@sergarace10 ай бұрын
Very helpful video, what's the part number for 2016 Toyota Corolla?
@YoseeChannel582 жыл бұрын
Hello Sir, Thanks for this solution i want to ask , i have corolla 2013 - 2014 and sometimes when i drive the radio do restart by itself , is that problem related to the broken touch screen that i have ?
@Ludwig-fg7zg2 жыл бұрын
Hey man, thanks. good video and explanation. question roughly how much did you pay for the new one?
@herrenmann2 жыл бұрын
It’s on the eBay link in video description. Thanks!
@barrigany3 жыл бұрын
Genius.... Ok. Something that should be noted about the ribbons. The don't all have the same type of release. I wish I would've known or figure that out before trying to flip up ones that aren't supposed to be flipped up.
@JohnBowden-kk9jq Жыл бұрын
Great video.
@scottsimmons8338 Жыл бұрын
Very helpful video. Where did you find and purchase the replacement touch screen? Thank you
@dlbtrung2 жыл бұрын
My Corolla 2016 runs into the similar problem today, but not only the touch is not working but also the volume button as well. Is it also related to the touch screen panel or do I need to replace other part?
@coe3534 Жыл бұрын
I have a blue tooth module not connected after I changed the digitizer how to I clear that in a Corolla 2015 ? PLEASE HELP
@Balvarez022 жыл бұрын
My replacement touch screen had the ribbon cable oriented differently from the original. For anyone doing this job check that the connection on your ribbon cable is facing down. The top will be solid. Hope this helps someone
@christinavansant26253 жыл бұрын
I think it would be helpful to show how to release the ribbon around 7:30. It goes off camera and it was the only one i had trouble with.
@edgarnoriegaklug35204 жыл бұрын
Thank you for the tutorial 👌🏼
@jamesturnure97355 жыл бұрын
Outstanding video! I am about to tackle mine and curious to know where you purchased your replacement touch screen (digitizer)? I see some on eBay for $100 and others for $25...yet they all appear to be the same. Anyone have experiences that they can share?
@herrenmann5 жыл бұрын
thank you for the comment.
@LOLMasterDido4 жыл бұрын
Jervis Tan what’s your WhatsApp?
@LOLMasterDido4 жыл бұрын
Jervis Tan my car is with same problem
@DuneEcho Жыл бұрын
Worked for me! Thanks!
@syde00043 жыл бұрын
When I was removing the ribbons that attach to the circuit board I had two of the black things that look like they secure the ribbons pop off. I tried to still connect the ribbons to the board by placing them in the slots, but now the stereo won’t power on at all when I plug it into my car. Any suggestions?
@Backslasherton3 жыл бұрын
Hey, I just wanted to know if you ever figured this out. I've got the same issue where nothing powers on, but the backup camera is still working for me.
@neelimaramamuni47613 жыл бұрын
@@Backslasherton I too have the same problem.. if you have any solution please advise
@syde00043 жыл бұрын
@@Backslasherton I didn’t ever figure it out. I wound up buying an entirely new stereo/touchscreen to install. I asked around on Reddit and apparently if parts on the circuit board that hold some of those ribbons in place are damaged it’s hard to repair yourself. Rather than going through the effort to find somebody to repair the spots I had damaged I just got a new one.
@Backslasherton3 жыл бұрын
@@syde0004 Appreciate the response. Sounds like I'm gonna have to get a whole new unit.
@TheMadyuk4 жыл бұрын
Very helpful thank you
@10chaca10 Жыл бұрын
Thanks bro
@Zanbor593 жыл бұрын
GOOD JOB................THANK YOU
@obodude714 жыл бұрын
Very helpful, thanks!
@ronmoiseoff31114 жыл бұрын
Thank you great video
@kingjer1254 жыл бұрын
edit: I have a problem with my radio, The screen does not turn on and there is no audio but my backup camera works, do you know what this could be? Hey man Thank you for the video it was great! but I need help, The thinner Ribbon cable to the left of the big ribbon cable the blue plastic part fell off on the end that connects to the screen, Do I need this? and if so how do I make it stick.
@herrenmann4 жыл бұрын
the blue plastic is for convenience of pulling the ribbon out from the connector. should be fine without it as long as the actual ribbon is not damanged.
@davidhendersono11904 жыл бұрын
I have the same problem what did you end up doing
@kingjer1254 жыл бұрын
David Henderson O ended up buying a new one off ebay for $120 i bought the newer model I think its model number 153 do your research because theres 2/3 different models they all work but I opted to get a newer one since im replacing it.
@davidhendersono11904 жыл бұрын
KING VURORA okay thank u I may end up replacing the the whole thing with a whole newer radio
@JohnStax984 жыл бұрын
Thank you very much 😊 🙏
@giampierobo Жыл бұрын
Good explain.
@penatechris4 жыл бұрын
Thank you!
@jamesmyers18173 жыл бұрын
It worked!! Thank you :)
@dezbriel99813 жыл бұрын
Good job 👍
@strausst3 жыл бұрын
I noticed that the part says it will not work for navigation. Do you have a touch screen for the 86100-02101 radio with the screen plate No. 100150 ?
@herrenmann3 жыл бұрын
Hi. It is for Toyota radio with nameplate 100150
@Jony04874 жыл бұрын
Thank you.
@surensath9864 жыл бұрын
Hey, great video. My head unit keeps rebooting. Do you know what would be causing that or how to fix it?
@herrenmann4 жыл бұрын
hi. similar to a pc, it could be a software or hardware problem. i would suggest to try a hard reset first. and if it doesn't work, try to take the radio unit out (unplug all the cables connecting to the radio) and plug it in back in after 1-2mins. see how it goes.
@luisfortes21664 жыл бұрын
Did you remove the plastic film from the new touchscreen before installing it?
@herrenmann4 жыл бұрын
Yes sir. Please remove the plastic film from the screen. Both front and back. Thanks.
@luisfortes21664 жыл бұрын
@@herrenmann Thank you so much for your helpful video, and recent customer service! This process took about an hour and works perfectly.