How to Replace Rear Brakes 2006-2011 Chevrolet HHR

Buy Now!
New Brake Drum Set from 1AAuto.com 1aau.to/ia/1ABDS00533
This video shows you how to install new rear drum brakes on your 2006-2011 Chevrolet HHR. Even though they are an older technology, you still find drum brakes on the rear of many modern vehicles. Like disc brakes, the brake drum and shoes will wear down over time, requiring replacement.
This process should be similar on the following vehicles:
2006 Chevrolet HHR
2007 Chevrolet HHR
2008 Chevrolet HHR
2009 Chevrolet HHR
2010 Chevrolet HHR
2011 Chevrolet HHR
Tools you will need:
• Pry Bar 1aau.to/oeh/1AXAA00020
• 13mm Wrench 1aau.to/od9/1AXAA00010
• 15mm Socket 1aau.to/opC/1AXAA00015
• 19mm Socket 1aau.to/ogH/1AXAA00043
• Hose Pinch-Off Pliers
• Locking Pliers 1aau.to/oay/1AXAA00139
• Needle nose pliers 1aau.to/oci/1AXAA00051
• Needle nose pliers 1aau.to/oci/1AXAA00052
• 3/8 Inch Air Impact Gun
• Torque Wrench 1aau.to/ojb/1AXAA00044
• Brake Grease
• Brake Parts Cleaner
• Copper Anti-Seize
• Hammer 1aau.to/oee/1AXAA00091
• Rubber Mallet 1aau.to/oab/1AXAA00413
• Small Hook
Subscribe: / @trq
Check out our playlist:
BMW X3 2004-10 1st Gen E83: • BMW X3 2004-10 1st Ge...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

[@tonystubbs9189]

How about explain that the sensor and bearings don't have to be removed or loosened to change out the brake shoes. People will get confused.

[@ThePeopleVerse]

You unplugged the sensor and never mentioned it again. Where did it come in to? Was it in the new bearing?

[@mkurpis82]

Thank you so much for your very informational video!! Very helpful! Super grateful!

[@leondecoteau9268]

Thanks for the information, great job.

[@curtisroystoniii1738]

Why was the axel replaced🥺

[@superdow1000]

Not sure whey you are bleeding the brakes just to change the shoes.

[@theiceageiscoming.5516]

Thanks! 💪😎🇺🇲

[@abibodlogistics]

Why not first of all clean all the dirty surface before putting in the new shaft.

[@karlharris595]

Not an hhr

[@bustownbc2787]

I dont know how your springs were so easy to put on... i bought replacements from napa and their so stiff they barely move.. you looked like you barely used any effort

[@GAHJIE]

DON'T TRUST ANYTHING FROM TRQ -WORST PARTS I EVER PURCHASED! Especially when it comes to break parts and suspension! Got break parts for front and rear for 1 SEDAN and 1 SUV and BOTH sets were shot after 2 months. The set on the SUV cause major issues causing a lot of money to fix. Also got suspension for the Sedan as well for both front and rear. The front quick strut assembly wasn't quick at all as it wasn't a good fit into the control arm and was at 50% after only a few months. The rears couldn't even be installed because the nut on the strut was cross-threaded from the factory. Yes, everything was the correct part number.

[@jamesmelton2622]

To muçh talking before work

[@Gfysimpletons]

Awful