Made a mistake in editing, I left out the part where you are working the parking brake. You need to hold the regular brake while you work the parking brake. Thank you all for watching!
@Ricklustt3 жыл бұрын
What do you mean by hold regular brake while working parking brake. Will this somehow let the caliper slide off ? My car is jacked up now and I’m searching videos on "how to" give me some slack in the Emergency Brake Cable
@Blazer02LS6 жыл бұрын
It's a good idea on that P-Brake design to take a pick and walk it around the piston between the boot so the boot doesn't twist and fold with the piston as it is screwed back in. A small bit of silicone grease in there is a good idea as well.
@46fd043 жыл бұрын
FYI I own an '09 Grand Caravan since brand new. If you are replacing the rear brake pads every year, the brakes are dragging. Do not replace the caliper until you check the parking brake. If it's partially applied, the cause is a parking brake cable seizing up. You will most likely need to replace the cable, not the caliper. Took me 7 years to figure that out. Even my local Dodge Dealer missed it
@2carpros3 жыл бұрын
Good tip! Thanks for watching!
@chimeric77744 жыл бұрын
"people on KZbin will make fun of you" lol Excellent quality instructional video. Thank you for the education. Liked and subscribed.
@2carpros4 жыл бұрын
Thanks so much!
@eddiea37824 жыл бұрын
I needed that tool. I couldn't get the piston to move with a pair of pliers. I would have damaged that piston and the boot otherwise. Good video. It was very helpful to me.
@2carpros4 жыл бұрын
Very cool! Thanks for watching Eddie!
@adamhamann39072 жыл бұрын
c clamp works
@DaveDrawing2 жыл бұрын
@@adamhamann3907 not for pressing the piston in, it has to be rotated.
@adamhamann39072 жыл бұрын
Worked perfect for Me a c clamp
@DaveDrawing2 жыл бұрын
@@adamhamann3907 sorry, if you have a vehicle like the one in this video, you can't compress the piston just by pressing on it. It's not physically possible. The brakes you worked on must have been either on the front, or on a vehicle without this type of piston. It must be rotated in.
@peterkumo11534 жыл бұрын
Good video. I learned a few things. Thank you. Could you do a video on replacing the caliper and what you must do with that spring on the brake cable.
@Ricklustt3 жыл бұрын
That would really help. I’m going to try and wiggle it off again. No luck the first time. Did you find a solution?
@jordandreste54802 жыл бұрын
Thank you so much you save the day I could not figure out the rear brakes, and shame on those who made fun of any of your videos they are despicable
@2carpros2 жыл бұрын
Thank you so much for watching Jordan. That's the internet sadly. Keyboards makes everyone a tough guy. Thanks for watching!
@topfloorstudio26842 жыл бұрын
Thanks for this vid. I'm getting ready to do my rear brakes on my 2015 Grand Caravan. Hopefully they're the same. Subbed!
@2carpros2 жыл бұрын
Thanks for the sub! They should be the same or very similar. Thanks for watching!
@benjastanpolanco6528 Жыл бұрын
Thank you I was just turning it in and not punching in😳
@awebuser59142 жыл бұрын
I'm puzzled why there are threads on the middle of the tool? Does the tool "push" in any way, or does it simply turn the piston? Seems that you could simply have a supported shaft with the round drive-plate and wind the piston in. Maybe the middle threads keep the round plate in contact with the piston, but wouldn't you need to have exactly the same pitch of thread in both the tool and caliper (distance moved per turn...)?
@onlyme88702 жыл бұрын
I've used needle nose pliers and press and turn the piston in. The tool is threaded to add pressure as its turned the tool has mated surface that matches in some grooves on the piston which turns the piston head as its being pressed. I have a Fiat 500l and 2010 Grand Caravan both with this type of rear spindle type piston I don't like them but is what it is.
@DaveDrawing2 жыл бұрын
You're right, it does press in while turning. The threads on each part are not the same, so it requires occasional adjusting of the drive bolt. These points are covered in the video, maybe have another look! 😉
@francesgalindez82983 жыл бұрын
Nicely Done on a clean and clear video. Just Subscribed.
@2carpros3 жыл бұрын
Thanks for the sub!
@steveingalls67984 жыл бұрын
Why didn't you show the procedure for cleaning the caliper bracket abutment clip area, lubing under the abutment clips, installing the abutment clips correctly & lubing the piston face. Failing to do so can result in uneven pad wear.
@tjd23263 жыл бұрын
Because hes not exactly a pro
@ralphcoccio37996 жыл бұрын
Nice job. Very helpful.
@2carpros6 жыл бұрын
Thanks for watching!
@oldzymedia4 ай бұрын
Can u use c clamp to push cylinder back instead of the tool u used.
@JulioGarcia-mf2tq3 жыл бұрын
Why not put 2 wheel nuts to hold tje rotor in place while installing the caliper?
@DaveDrawing2 жыл бұрын
That's a good idea, it will also keep bits of crud from getting in between!
@lance-pc1qz4 жыл бұрын
that tool is way faster then a 3/4 thanks
@papabits57212 жыл бұрын
Just put piston pins at 12 and 6 o’clock
@excelisfun6 жыл бұрын
Great video,a s always!!!!
@2carpros6 жыл бұрын
Always nice to hear :)
@MrPatrick51503 жыл бұрын
The rear caliper piston needs to be rotated in but not the front, correct? And is there a way in general, to look at the piston caliper and tell if it needs to be rotated or not as it's compressed?
@2carpros3 жыл бұрын
Correct. The parking brake is just for the rear. Yes. It will have the little divots in the piston. Thanks for watching!
@MTBeach3 жыл бұрын
I don't understand at 7:30 talking about lining up the piece on the brake pad with the notebook the caliper. Since the piston spins out won't that just defeat lining it up?
@alfredbernal86032 жыл бұрын
Exactly what i thought as well...
@adampetersen5112 жыл бұрын
I purchased Duralast Gold ceramic rear brakes from Autozone. They do not come with the "little notch" on the rear side of the brake pad to slide into the piston indent. Do you happen to know why?
@2carpros2 жыл бұрын
It should if it's for this Caravan with the ratchet type emergency brake. Maybe Autozone gave you the wrong pads? Thanks for watching!
@u2ammon2 жыл бұрын
You cut off the part of putting on the caliper bracket... What?
@raymae90513 жыл бұрын
I watched this whole video...and I don't even have a Dodge Caravan.
@2carpros3 жыл бұрын
Well thank you! :D
@jefferymorton970410 ай бұрын
You never Said to Break the Bleeder screw..Messes up the whole thing..other than that your great
@2carpros10 ай бұрын
You don't need to. You just need the special tool. Thanks for watching!
@jefferymorton970410 ай бұрын
ON THE DRIVER SIDE IT NEEDED TO BE DONE ON MY 2016
@lance-pc1qz4 жыл бұрын
a 3/4 works well
@tjd23263 жыл бұрын
But wait your not done just yet!
@ResidenceRescueLLC6 жыл бұрын
Needle nose pliers work just fine tool instead of wrestling with that tool.
@kyleNL4 жыл бұрын
Yep. Figured this out stoned on a friday night with my only vehicle taken apart. Lol
@TheOutwiththeold4 жыл бұрын
not in the salt states....
@kyleNL4 жыл бұрын
@@TheOutwiththeold in toronto, Canada and St. Johns Newfoundland it worked for me. Struggled a bit but it worked.
@njack89863 жыл бұрын
Why does the rotor smaller but for the same vehicle? Auto zone has two different sizes and they say it will work for either size?
@2carpros3 жыл бұрын
Sometimes different breaking systems will use different sized rotors. But your replacement rotor needs to be the same size as the new one. I would measure your old one just so you have that info at the parts store. I have no idea why AutoZone thinks there is 2 different sizes for the rotor. Thanks for watching!
@mehdiabdennadher74072 жыл бұрын
35 NM - 100 NM - 135 NM
@hahakevin4414 жыл бұрын
W
@justinmccallister2803 жыл бұрын
Too easy! I want to see a car from Michigan that has a season or two of road salt, than talk to me about breaker bars and all that!
@2carpros3 жыл бұрын
Well I live in the desert, doesn't snow a ton here lol Thanks for watching!
@donaldshimkus5394 жыл бұрын
Very informative and helpful, thanks. But PLEASE, use your wrenches and pliers in the correct direction ! Oh, and please learn the difference between a notch and a pin. One is an outty and one is an inny. Lol.