How to Replace Safely Harmonic Balancer Crank Pulley 01-11 Ford Ranger

Shop for New Auto Parts at 1AAuto.com 1aau.to/c/82/c/...
1A Auto shows you how to repair, install, fix, change or replace a screeching, squeaking or worn engine harmonic balancer. This video is applicable to the 01, 02, 03, 04, 05, 06, 07, 08, 09, 10, 11 Ford Ranger or Mazda Pickup.
This process should be similar on the following vehicles:
1998 Ford Ranger
1999 Ford Ranger
2000 Ford Ranger
2001 Ford Ranger
2002 Ford Ranger
2003 Ford Ranger
2004 Ford Ranger
2005 Ford Ranger
2006 Ford Ranger
2007 Ford Ranger
2008 Ford Ranger
2009 Ford Ranger
2010 Ford Ranger
2011 Ford Ranger
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/orI/1AX...
• Phillips Head Screwdriver 1aau.to/orI/1AX...
• Pry Bar 1aau.to/oe6/1AX...
• Complete Metric Wrench Set 1aau.to/oeS/1AX...
• Complete Metric Socket Set 1aau.to/ohV/1AX...
• Harmonic Balancer Puller 1aau.to/oi/1AEH...
• Channel-Lock Pliers 1aau.to/oaM/1AX...
• 1/4 Inch Ratchet 1aau.to/oo2/1AX...
• 3/8 Inch Breaker Bar
• 3/8 Inch Drive Ratchet 1aau.to/orP/1AX...
• Torque Wrench 1aau.to/okR/1AX...
• Floor Jack 1aau.to/ofp/1AX...
• Jack Stands 1aau.to/oe3/1AX...
Subscribe: / @1aauto
Check out our playlist:
Ford Ranger 1998-2012 3rd Gen: • Ford Ranger 1998-2011 ...
Ford Auto Repair Videos: • Ford Auto Repair Videos
For More Info visit us at 1aau.to/h/DH/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@sharpend2173]

Do you have any video's of a cam synchronizer replacement on this same engine? I have been looking for my synchronizer for 4 months now and still can't find it???

[@bryceyoda]

I just did this this job ended up being a bit of a nightmare. The puller bolts were to short and needed 8mmx1.25x100mm long. After installing the dorman harmonic balancer I started getting misfire codes P0300 P0303 p0304. I changed out the crank sensor and spark plugs. I ended up pulling the balancer back off and found that the pickup teeth for the sensor were bent on the new balancer. Make sure to check your new one before install. I just wanted to share this info for others.

[@JohnSmith-fb2np]

I have always liked 1A Auto videos. Usually more professional than many of the DIYers. But you guys need a bit more info on this one. 1. The crank angle sensor removal 2. The store bought crank tools have short 80mm 8x1.25 bolts. And most hardware stores don't sell the 90mm or longer bolts needed for this deep balancer. Where do you get them? Otherwise this was a great video as usual.

[@homersmith9132]

excellent video. not rushed, clear audio.one step I would add is start the engine and check for correct belt tracking as soon as the belt is back in place. Thanks for the production.Worth mentioning is the fact that starter removal is not necessary if vehicle has manual transmission

[@1AAuto]

+Homer Smith Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c

[@traecummings9853]

Need to change oil pan gasket and front Crank seal, this vid helped greatly. Thank you.

[@zackwalker684]

My balancer was so torn that it ruined the holes so I had to use 2 different pullers. Lucky I was at work and had the correct tools

[@pondfrog777]

What size bolts do you use to put into the harmonic balancer puller

[@shanec4441]

Most mechanics put sealant or grease on keyway to keep it from leaking oil on the keyway

[@JeffAMay]

If you have Air and a 1/2" impact you don't need to take the starter off...

[@renerojas6950]

Good job really good information thank you 1 A auto keep it going for a good time

[@1AAuto]

+Rene Rojas Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

[@rafaelmontelongo5394]

Helped me out! Thanks ! One question, did this truck have a sensor.? Only thing I didn’t see put on. 👍

[@budjordan3803]

Palm wratchet works 👍🏽

[@1AAuto]

+@budjordan3803 Thanks for the feedback!

[@jeinerflores4894]

Good job guys! Very Well explained. Thank you!

[@standingtall952]

Nice thanks..

[@TheBruceTR]

My engine is in my truck (not on an engine stand). I don't have an impact wrench. When I go to loosen the crank bolt (using a breaker bar), will I be able to use the belt to keep the engine from rotating counterclockwise? Please advise. Many thanks!

[@williambond5833]

What thread pitch are the two bolts you use eith the puller?

[@andrewrodriguez8492]

How do I find TDC on the Ford Ranger?

[@coltonthomas8466]

What should I do if it’s rusted on

[@brandonwebb1819]

How far does that seal go in for the crankshaft seal

[@civilianwilly]

19mm crank pulley bolt. YW

[@mattdoe531]

Can I keep the starter on? mine is impossible to remove

[@tooterturtle7849]

If you have a manual leave in gear

[@Slidenomad]

what happen if you rotate the balancer.... is that bad

[@gitar1hero1qaz]

what size hardware to thread into balancer to use with puller? I have tried 1/2-20, 1/2-13, 3/8-16, 3/8-24 and all are either too big or too small.

[@jessgvirtual5822]

5/16 - 18 on Ranger 1999, 2.5L, 4cyl.

[@shanec4441]

There is a flywheel locking tool that bolts onto the starter mount location . Remove the starter and install the locking tool in its place.

[@mcfriedchicken1972]

Why does my balancer start to crank when I try removing it

[@gitar1hero1qaz]

you have to jam a screwdriver into your flywheel where you took the starter out to keep it from spinning.

[@Slidenomad]

@@gitar1hero1qaz is it bad if the balancer rotates

[@Robert-bm5fz]

pulling the starter? naa.